DTS SLICE Free Motion Headform User manual

© Diversified Technical Systems, Inc. - All Rights Reserved
SLICE Free Motion Headform (FMH)
User’s Manual
January 2018

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 2(Rev. 0)
Table of Contents
DTS Support.................................................................................................... 3
Introducing the SLICE FMH Headform System ................................................ 4
Overview of SLICE FMH Headform System ...................................................... 4
Customer Provided: FMH Headform Skin & Skull.............................................4
24000-00341: FMH Upper Neck Integration Kit ..............................................5
24000-00355: FMH Headform DAS Kit...........................................................5
13000-40760: Free Motion Headform (FMH) USB Interface Kit .........................6
Communications..............................................................................................6
Power/Charging Requirements ..........................................................................7
Status LED .....................................................................................................8
Basic Care and Handling ................................................................................. 9
Shock Rating ..................................................................................................9
Mounting Considerations...............................................................................9
Thermal Considerations....................................................................................9
SLICEWare Software ..................................................................................... 10
Software Installation......................................................................................10
Communicating with the SLICE FMH Headform System ......................................10
Level Trigger Setup .......................................................................................11
How to Auto-Arm the SLICE FMH Headform System...........................................11
Troubleshooting.........................................................................................13
Downloading Data .........................................................................................13
Viewing Data ................................................................................................13
Exporting Data..............................................................................................16
Real-Time Mode ............................................................................................17
Appendix A: SLICE Hardware Specifications................................................. 18
Appendix B: Pin Assignments....................................................................... 19
13000-30131 Termination Specifications ..........................................................19
12-pin Interface Connector .............................................................................19
5-socket FMH Head Interface Connector...........................................................20
12-socket FMH Head Interface Connector* .......................................................20
Appendix C: SLICE FMH Headform DAS Kit Contents .................................... 21
Appendix D: SLICE FMH Headform Assembly Procedure .............................. 22
Appendix E: Minimizing System Self-Heating ............................................... 28

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 3(Rev. 0)
DTS Support
SLICE data acquisition systems are designed to be reliable and simple to operate. Should
you need assistance, DTS has support engineers worldwide with extensive product
knowledge and test experience ready to help via telephone, e-mail or on-site visits.
The best way to contact a DTS support engineer is to submit a request through the DTS
Help Center web portal (support.dtsweb.com). You must be registered
(support.dtsweb.com/registration) to submit a request
(https://support.dtsweb.com/hc/en-us/requests/new). Registration also enables access
to additional self-help resources and non-public support information.
This manual supports the following products:
13000-40760: Free Motion Headform (FMH) USB Interface Kit
24000-00341: FMH Upper Neck Integration Kit
24000-00355: FMH DAS Interface Kit
13000-20100: SLICE NANO Base+ (10-10 cm)

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 4(Rev. 0)
Introducing the
SLICE FMH Headform System
The SLICE FMH Headform system is a miniature data acquisition system (DAS) designed
for integration into a FMH headform. It includes a battery sufficient to run the system
for up to 20 minutes and supports autonomous operation after arming. After the test,
reconnecting the system to a PC and the provided power supply allows data download,
viewing and post-processing, and recharges the battery for the next use.
Overview of SLICE FMH Headform System
A typical 3-channel system is discussed below. Your system may vary if you have
additional channels or custom features.
Detailed information about the SLICE DAS Kit can be found in Appendix C: SLICE FMH
Headform DAS Kit Contents.
Detailed assembly procedures can be found in Appendix D: SLICE FMH Headform
Assembly Procedure.
The FMH Headform is integrated with DTS’s SLICE NANO Base+, SLICE NANO Bridge,
and SLICE NANO FMH Headform Battery. Detailed specifications for the SLICE Base+
and Bridge can be found on page 18 (Appendix A: SLICE Hardware Specifications) or at
support.dtsweb.com. Details on charging the SLICE NANO FMH Headform Battery can
be found on page 7 (Power/Charging Requirements). For information on operation of
the SLICE system, please see the SLICE User’s Manual.
Customer Provided: FMH Headform Skin & Skull
This component is standard on all FMH Headforms.
Figure 1: FMH Headform Skin & Skull (Customer Provided)

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 5(Rev. 0)
24000-00341: FMH Upper Neck Integration Kit
This kit is required for every SLICE FMH. This kit is used to integrate the SLICE Data
Acquisition and sensors into the FMH Headform. The replaces the standard FMH / H3
upper neck load cell structural replacement.
Figure 2: FMH Upper Neck Integration Kit (24000-00341)
24000-00355: FMH Headform DAS Kit
This kit is required for every SLICE FMH. Details of this kit can be found in Appendix C:
SLICE FMH Headform DAS Kit Contents.
Figure 3: FMH Headform DAS Kit (24000-00355)

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 6(Rev. 0)
13000-40760: Free Motion Headform (FMH) USB Interface Kit
This Free Motion Headform (FMH) USB Interface Kit connects the USB port on your PC
and a power supply provided with your system to the FMH Headform via the upper neck
structural replacement connector. The SLICE USB Interface connects the FMH Headform
SLICE system to a PC via USB. It also powers the SLICE system and charges the on-
board battery. A 12 V, 2.5 A power supply is provided with your system. It will
simultaneously charge the battery and power the SLICE FMH Headform system until it
is disconnected prior to the test. Battery capacity and charging requirements can be
found on page 7 (Power/Charging Requirements).
Figure 4: Cable and Headform Interface
Figure 5: Power Supply and SLICE USB Interface
Communications
A USB-to-PC communication and power cable is provided with your system. All
communication signals and power/battery charging are supported via the LEMO
interface. Information on installing the software, initializing the system, downloading
and viewing the data begins on page 10 (Power/Charging Requirements).

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 7(Rev. 0)
Power/Charging Requirements
The SLICE NANO FMH Headform Battery contains an integrated, 8.4 V, 80 mAh,
rechargeable lithium battery sufficient to operate the system for cable-free testing.
When the 12 V, 2.5 A power supply is connected to your system, it will simultaneously
charge the battery and power the SLICE FMH Headform system until it is disconnected
prior to the test.
Battery life (fully charged)
Up to 20 minutes (full sensor load)
Charge time
~1 hour from complete discharge to full charge;
always charges when connected to power supply
Charging the system using a maximum of 12 V and without the USB connected
minimizes system self-heating. Additional details can be found in Appendix E:
Minimizing System Self-Heating.

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 8(Rev. 0)
Status LED
This LED is green and provides information on arming and recording status. It is on, off
or blinking.
Blinking
After unit is turned on, LED will blink during sensor warm-up and system arming.
ON
If armed in Circular Buffer mode, the LED will begin recording after sensor warm-
up and the LED will go solid green. The LED will also go solid green in Recorder
mode if the system received a START signal.
OFF
If armed in Recorder Mode, the system will stop blinking and go OFF, waiting for
a START signal to begin recording.
Circular Buffer Mode
Recorder Mode
(rate increases) Arming; sensor warm-up (~30 sec)
(LED is ON)
System is recording
(LED is OFF)
Waiting for START signal
(rate steady) If the LED continues to blink after 45 sec,
the system did not initialize properly.
See page 13 (Troubleshooting).
To arm the system, press and hold the push button switch for >3 sec. After 7 sec, the
LED will begin to blink, indicating the system is performing the auto-arm initialization
sequence. After 32 seconds, the LED will be either on (Circular Buffer mode) or off
(Recorder mode). Note: The SLICE FMH Headform system’s auto-arm feature must be
software-enabled prior to pushbutton initialization. Only Circular Buffer mode is

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 9(Rev. 0)
recommended for use with the FMH Headform. Details on software installation and use
begin on page 10 (SLICEWare Software).
Basic Care and Handling
The SLICE FMH Headform is a high precision measurement system designed to operate
reliably in dynamic testing environments. Though resistant to many environmental
conditions, care should be taken not to subject the unit to harsh chemicals, submerge it
in water, or use it in a manner inconsistent with its intended purpose.
The SLICE NANO Base, Bridge and FMH Headform Battery are supplied with calibration
data from the factory. DTS recommends annual recalibration to ensure that the system
is performing within factory specifications. SLICE hardware is not user-serviceable and
should be returned to DTS for service or repair.
Shock Rating
The SLICE FMH Headform system is rated for 500 g, 4 ms duration, in all axes. All
mounting considerations should be thoroughly addressed to ensure the system is
adequately integrated to survive the expected shock loads.
Mounting Considerations
To provide the best shock protection, the system should be securely bolted inside the
FMH Headform skull using the proper hardware and recommended torque specifications.
Care must be taken to restrain the cables to permit adequate strain relief and minimal
movement upon impact.
Thermal Considerations
SLICE NANO DAS is an extremely low power system with negligible self-heating. Should
any self-heating be a concern, this can be addressed by charging the system properly
and minimizing the time it takes to arm the system and perform the test (see Appendix
E: Minimizing System Self-Heating). Should you have any questions about using SLICE
in your environment, please contact DTS.

SLICE Free Motion Headform User’s Manual January 2018
support.dtsweb.com 10 (Rev. 0)
SLICEWare Software
Software Installation
1. Locate the set-up.exe file on the CD or USB drive provided. Double-click the file
to begin the installation and follow the prompts on your screen.
2. When installation is complete, copy the XML file found in the folder “copy contents
to SLICEWare directory after software install” to the SLICEWare directory.(The
XML file contains the sensor information.) If you were not provided an XML file,
you will have to enter this information later.
3. Start SLICEWare by double-clicking the desktop icon or go to Programs/
SLICEWare.
If you have any questions about software installation, please contact DTS Support. For
a detailed software manual, please see support.dtsweb.com.
Communicating with the SLICE FMH Headform System
4. Connect cable to the LEMO receptacle on the backplate (Figure 4). Next, connect
the cable to the power supply provided (Figure 5) and your PC. (The SLICE FMH
Headform system can be connected to the PC before or after starting the
software.)
5. If you provided your own sensors or had to replace a sensor, you can manually
enter the sensor information into the SLICEWare software before using your SLICE
FMH Headform system. (Check that the sensors that are installed in the FMH
Headform are visible on the tab. If any sensor is missing, you need to
manually install it.) You will need the calibration data provided with your sensors
to do this. Each sensor must also be assigned to the correct axis and optional
ISO code.