Dual iplug MXDMA65 Operating instructions

INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA/iPod™ Ready Receiver with Detach Face
MXDMA65

2
MXDMA65 INSTALLATION
Preparation
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
• Mount the iplug™ adapter to any
smooth clean surface using the
supplied double-sided tape or
#2 x 3/8” Phillips head screws.

3
MXDMA65 INSTALLATION
Wiring Diagram
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The MXDMA65 uses one
10 amp ATM fuse located
beside the wiring connector.

4
MXDMA65 OPERATION
Control Locations
Release
Band/Play/Pause
Volume
Mode/Search
Preset 4/Menu
Preset 1/Repeat
Preset 5/Folder Down
Preset 2/Random
Preset 3/Intro
Eject
Preset 6/Folder Up
1
2
3
4
5
6
7
8
9
10
11
EQ/9
Loudness
Display/0
Tuner Scan/8
Mute
Return/7
Auto Store/Preset Scan/Enter
Power
Tune/Track Down
Tune/Track Up
12
13
14
15
16
17
18
19
20
21
1921 18 17 16 15 14 13 12
1 2 35 6 789 10 11
The MXDMA65 allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
4
20

5
MXDMA65 OPERATION
General Operation
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Press POWER or any other button (except eject) to turn the
unit on. Inserting a disc will turn the unit on automatically.
Press POWER to turn the unit off.
Press MODE to select between tuner, CD player, auxiliary
input and iPod mode. Modes of operation are indicated in the
display.
Press LOUD to activate and deactivate the loudness contour
curve. Activating this feature will enhance the bass and
treble frequencies when listening to music at low volumes.
Adjust volume using rotary encoder (00-46).
Press and hold POWER for 3 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time,
or MP3/WMA/iPod song information.
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE
nn
to adjust the
hours and TUNE
ll
to adjust the minutes. Press DISP
momentarily to save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Faceplate Removal
Semi-permanent
Faceplate Installation
Power On/Off
Mode
Loudness
Volume
Programmable
Turn-On Volume
Preset EQ Curves
Display
Set the Clock
12/24-hour Clock

6
MXDMA65 OPERATION
General Operation - Setup Menu
Menu Function Options Action
Tuner Frequency
Spacing
FREQ USA Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
FREQ EUR Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Clock Display CLK OFF Programs the unit to not display the clock when the
power is off.
CLK ON Programs the unit to display the clock when the
power is off.
Auxiliary Mode AUX ON Enables access to auxiliary mode.
AUX OFF Disables access to auxiliary mode.
Beep
Confirmation
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
Local/Distance
Tuning
LOC OFF Activates Distance tuning.
LOC ON Activates Local tuning for strong station reception
only.
Power on
Message
MSG OFF Disables power on message.
MSG ON Enables power on message to be displayed.
Made for iPod
Message
DEMO ON Enables Made for iPod message to be displayed
every 60 seconds in Tuner and Aux modes.
DEMO OFF Disables Made for iPod message.
Reset
Mute
Setup Menu
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
Press and hold the rotary encoder for more than 3 seconds
to access the setup menu. Press the rotary encoder
momentarily to select between the menu functions and
rotate the rotary encoder left/right to adjust or activate the
desired function.

Press rotary encoder to select between Volume (default),
Bass, Treble, Balance & Fader.
Press rotary encoder until BAS appears
Rotate encoder left/right to adjust
( -6 minimum / +6 maximum)
Press rotary encoder until TRE appears
Rotate encoder left/right to adjust
( -6 minimum / +6 maximum)
Press rotary encoder until BAL appears
Rotate encoder left/right to adjust
(BAL L 12-BAL 00-BAL R 12)
BAL 00 represents equal balance
Press rotary encoder until FAD appears
Rotate encoder left/right to adjust
(FAD F 12-FAD 00-FAD R 12)
FAD 00 represents equal fader
Individual Bass and Treble settings are retained in memory
for AM, FM, CD, AUX and iPod modes. This allows you to
save the Bass and Treble settings separately for each mode.
Example:
FM tuner mode can have Bass +3 and Treble -1 while CD
mode can have Bass +2 and Treble +2.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
7
MXDMA65 OPERATION
BASSVOLUME TREBLE BALANCE FADER
General Operation
Audio
Bass
Treble
Balance
Fader
Source Audio Memory

Press TUNE
nn
or TUNE
ll
momentarily to seek the
next strong station.
Press TUNE
nn
or TUNE
ll
until "MANUAL"
momentarily appears in the display, then release. Press
TUNE
nn
or TUNE
ll
momentarily to move radio
frequency up or down one step at a time. Press and hold to
advance quickly. If tuning is not adjusted for 5 seconds, the
unit will return to seek tuning mode (default). "AUTO" will
momentarily appear in the display.
Press SCN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCN again to cancel.
Press BAND to select between FM1, FM2, FM3, AM1 and AM2
bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Note:
Function buttons 7, 8, 9 and 0 apply to MP3 and WMA
playback only.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Distance tuning is activated during the initial band scan.
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
8
MXDMA65 OPERATION
Tuner Operation
Seek Tuning
Manual Tuning
Scan Tuning
Band
Storing and Recalling
Station Presets
Automatically Store
Stations
Preset Scan

Insert CD
Eject CD
Track Select
Fast Forward and Reverse
Pause
Intro
Repeat
Random
CD-R/CD-RW Compatibility
With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
Press EJECT to eject the CD. The unit will change to previous
mode of operation (Tuner, Aux, or iPod mode). If the disc is
not removed within 10 seconds, the unit will reload the disc.
The unit does not have to be turned on to eject CD.
Press TRACK
ll
to skip to the beginning of the next track.
Press TRACK
nn
to return to the beginning of the current
track. Pressing TRACK
nn
again skips to the beginning of
the previous track.
Press and hold TRACK
ll
or TRACK
nn
to fast forward
or reverse a track.
Press
l
/ II to temporarily stop CD playback.
Press
l
/ II again to resume playback.
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between tuner, CD player, auxiliary input and iPod
modes and when the unit is turned on/off.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight for
extended periods of time, CDs recorded in which a recording
session failed or a re-recording was attempted and, or
encrypted or copy-protected CDs which do not conform to
the audio CD-DA red book recording standard.
9
MXDMA65 OPERATION
CD Player Operation

10
MXDMA65 OPERATION
CD Player Operation - MP3/WMA Files
Playing an MP3/WMA Disc
MP3 Icon
WMA Icon
Folder Icon
Displaying Information
Character Support
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
The icon will illuminate anytime a valid MP3 encoded
disc is inserted and flash in MP3 search/navigate modes.
The icon will illuminate anytime a valid WMA encoded
disc is inserted and flash in WMA search/navigate modes.
The icon will illuminate anytime a folder is selected in
the file/folder search modes.
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, Artist Name and Album name will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name