Dual XDM6400 Operating instructions

INSTALLATION/OWNER'S MANUAL
AM/FM/CD/MP3/WMA/USB/3.5mm/Bluetooth® Ready Receiver with Detachable Face
XDM6400

2
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit,
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
XDM6400 INSTALLATION
Preparation

3
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDM6400 uses one
10 amp ATM fuse located
beside the wiring connector.
XDM6400 INSTALLATION
Wiring Diagram
BLACK 8-pin Female Mini-DIN
BTM60 Connection (sold separately)
Antenna Connector

4
The XDM6400 allows playback of your favorite MP3 and WMA files recorded on CD-R and
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track
search - even while a song is currently playing!
Function keys 7, 8, 9 and 0 apply to Bluetooth and MP3/WMA operation only.
XDM6400 OPERATION
Control Locations - Receiver
Release
Eject
Mode/Search
Volume/Audio/Setup
Tune/Track Up
Talk/Redial
EQ/Key 9
Key 0
USB Port (Covered)
Auxiliary Input
Tuner Scan/Key 8
Key 7
1
2
3
4
5
6
7
8
9
10
11
Preset 6/Folder Up
Preset 5/Folder Down
Preset 4
Preset 3/Intro
Preset 2/Random
Preset 1/Repeat
Auto Store/Preset Scan/Enter/Key #
Band/Play/Pause/Key *
Display
Mute/End Call
Tune/Track Down
Power
12
13
14
15
16
17
18
19
20
21
2022 19 18 17 16 15 14 13
1235 6 7 8
12
4
21 11 10
9
22
2324
23
24

Faceplate Removal
Semi-Permanent
Faceplate Installation
Power On/Off
Mode
Auxiliary Input
Volume
Programmable
Turn-On Volume
Mute
Preset EQ Curves
Reset
Display
General Operation
XDM6400 OPERATION
5
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Press POWER or any other button (except eject) to turn the
unit on. Inserting a disc will turn the unit on automatically.
Press POWER to turn the unit off.
Press MODE to select between AM/FM, CD player, auxiliary
input, USB and Bluetooth (optional). Modes of operation are
indicated in the display.
NOTE: CD, USB and Bluetooth modes will not appear unless
a CD is inserted, a USB device (sold separately) is connected
or BTM60 (Bluetooth module - sold separately) is attached.
Insert 3.5 mm plug to connect your portable audio device.
Adjust volume using rotary encoder (00-46).
Press and hold POWER for 3 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
Press EQ to select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time,
or MP3/WMA/USB song information.

6
With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE
nn
to adjust the hours and
TUNE
ll
to adjust the minutes. Press DISP momentarily to
save the selected time.
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Press and hold the rotary encoder for more than 3 seconds to
access the setup menu. Press the rotary encoder momentarily
to select between the menu functions and rotate the rotary
encoder left/right to adjust or activate the desired function.
Set the Clock
12/24-hour Clock
Setup Menu
XDM6400 OPERATION
General Operation
Setup Menu
Menu Function Options Action
Loudness Curve LOUD OFF Disables the loudness function.
LOUD ON Enables the loudness function. Activating this feature
will enhance the bass and treble frequencies when
listening to music at low volumes.
Tuner Frequency
Spacing
FREQ USA Programs the unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
FREQ EUR Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Clock Display CLK OFF Programs the unit to not display the clock when the
power is off.
CLK ON Programs the unit to display the clock when the power
is off.
Auxiliary Input AUX ON Enables the front panel 3.5mm auxiliary input.
AUX OFF Disables the auxiliary input.
Beep
Confirmation
BEEP OFF Disables the confirmation beep.
BEEP ON Enables the confirmation beep.
Local/Distance
Tuning
LOC OFF Activates distance tuning.
LOC ON Activates local tuning for strong station reception only.
Power on
Message
MSG OFF Disables power on message.
MSG ON Enables power on message to be displayed.
Demonstration
Mode
DEMO ON Enables the "BT READY" message.
DEMO OFF Disables the demonstration mode.

7
XDM6400 OPERATION
Press rotary encoder momentarily to select between
Volume (default), Bass, Treble, Balance, & Fader.
Press rotary encoder until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press rotary encoder until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press rotary encoder until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Press rotary encoder until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Individual Bass and Treble settings are retained in memory
for tuner, CD, AUX, USB and Bluetooth modes. This allows
you to save the Bass and Treble settings separately for each
mode.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
Audio
Bass
Treble
Balance
Fader
Source Audio Memory
General Operation
BASSVOLUME TREBLE BALANCE FADER

8
XDM6400 OPERATION
Seek Tuning
Manual Tuning
Scan Tuning
Band
Storing and Recalling
Station Presets
Automatically Store
Stations
Preset Scan
Press TUNE
nn
or TUNE
ll
momentarily to seek the
next strong station.
Press TUNE
nn
or TUNE
ll
for more than two seconds,
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
nn
or TUNE
ll
momentarily to
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for five
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
Press SCN to preview strong stations on the current band,
pausing for five seconds at each. Press SCN again to cancel.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
two seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Note: Function keys 7, 8, 9 and 0 apply to Bluetooth, USB and
MP3/WMA operation only.
Press AS/PS for more than two seconds to automatically
store the six strongest stations in the current band.
Automatic local tuning is activated during the initial band
scan.
Press AS/PS for less than two seconds to scan presets 1-6
on the current band, pausing for five seconds at each. Press
AS/PS again to cancel.
AM/FM Tuner Operation

9
XDM6400 OPERATION
Insert CD
Eject CD
Track Select
Fast Forward and Reverse
Pause
Scan
Repeat
Random
CD-R/CD-RW Compatibility
With the label facing up, insert a standard size CD into the
CD slot. The CD will automatically begin playback.
Press EJECT to eject the CD. The unit will change to
previous mode of operation (tuner, AUX, USB or Bluetooth).
If the disc is not removed within 10 seconds, the unit will
reload the disc. The unit does not have to be turned on to
eject CD.
Press TRACK
ll
to skip to the beginning of the next
track. Press TRACK
nn
to return to the beginning of the
current track. Pressing TRACK
nn
again skips to the
beginning of the previous track.
Press and hold TRACK
ll
or TRACK
nn
to fast forward
or reverse a track.
Press
l
/ II to temporarily stop CD playback.
Press
l
/ II again to resume playback.
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory
when selecting between tuner, CD, AUX, USB and Bluetooth
modes and when the unit is turned on/off.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
CD Player Operation

10
XDM6400 OPERATION
CD Player Operation - MP3/WMA Files
Playing an MP3/WMA Disc
Displaying Information
Title Icon
Artist Icon
Album Icon
Folder Icon
Character Support
When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the album name is displayed.
This icon will illuminate when the folder name is displayed.
Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, Artist Name, and Album name, will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name