Dubaco DS-210 Series User manual

DS-210
Handheld Short Range CCD Scanner
User’s Manual

System Information----------------------------------------------------------------3
Interface Selection-------------------------------------------------------------------3
Keepboard Terminal-----------------------------------------------------------------3
Language------------------------------------------------------------------------------4
Keyboard Wedge Function-----------------------------------------------------4
Keyboard Speed---------------------------------------------------------------------5
Message Terminator----------------------------------------------------------------6
RS-232 Parameters----------------------------------------------------------------7
Baud Rate-----------------------------------------------------------------------------7
RS-232 Function Installation---------------------------------------------------8
Handshaking Protocol--------------------------------------------------------------9
Scan Mode---------------------------------------------------------------------------10
Buzzer set-up-----------------------------------------------------------------------11
Frequency-----------------------------------------------------------------------------11
Adjust Buzzer Tone-----------------------------------------------------------------11
Power On Tone----------------------------------------------------------------------11
Good Read Beep-------------------------------------------------------------------11
Character Installation------------------------------------------------------------12
Other Installation------------------------------------------------------------------15
Scanning Verify----------------------------------------------------------------------15
Bar / Space Seting------------------------------------------------------------------15
Laser Data Speed Up--------------------------------------------------------------15
BAR-CODE-INSTALLATION----------------------------------------------------16
UPC-A---------------------------------------------------------------------------------16
UPC-E---------------------------------------------------------------------------------18
EAN-13--------------------------------------------------------------------------------20
EAN-8----------------------------------------------------------------------------------22
Code 39-------------------------------------------------------------------------------24
Contents
Codabar------------------------------------------------------------------------------26
Code 93------------------------------------------------------------------------------28
Code 128----------------------------------------------------------------------------30
Interleaved 2of 5-------------------------------------------------------------------33
Industrial 2 of 5---------------------------------------------------------------------35
Matrix 2 of 5-------------------------------------------------------------------------37
China Post Code-------------------------------------------------------------------39
MSI / Plessey-----------------------------------------------------------------------41
Code 32------------------------------------------------------------------------------43
Code 11------------------------------------------------------------------------------44
APPENDIX A -- ASCII------------------------------------------------------------46
ASCII Table-------------------------------------------------------------------------47
APPENDIX B – Function Key Table----------------------------------------48
Function Key Code--------------------------------------------------------------49
1 2

Enter
System Information
Set All default
SW Version
Interface Selection
*Keyboard
RS-232
USB
Keyboard Terminal Type
End
*PC/AT/,PS/2
IBM PS/2 30-80
PS/2 25,30
IBM XT
IBM 5550
NEC 9801
End
Language
*USA
Spanish
Germany
Italian
French
Japan
Keyboard Wedge function
Function Key Emulation
*OFF
KB Emulation(For NB)
*OFF
ALT Mode
*OFF
Enter
ON
ON
ON
3 4

Enter
Inter-character Delay (Default：00)
Caps Lock
ON
*OFF
Num Lock
ON
*OFF
Appendix A (00H-64H)
Inter-message Delay (Default：00)
Appendix A (00H-0AH)
Delay time=set up data*100(ms)
Keyboard Speed (Default：00 )
Appendix A (00H-08H)
End
Enter
End
Message Terminator
*CR
ESC
Tab
CR + LF
None
5 6

Enter Enter
End End
RS-232 Parameters
BAUD Rate
1200
2400
4800
*9600
19200
38400
Data Bits
7
*8
Stop Bits
*1
2
Parity
*None
Even
Space
Odd
Mark
RS-232 Function Installation
Inter-character Delay (Default：00)
Appendix A (00H-64H)
Inter-message Delay (Default：00)
Appendix A (00H-0AH)
Delay time=set up da-ta*1(ms)
Handshaking Protocol Delay (Default：00)
Appendix A (00H-0AH)
Delay time=set up da-ta*100(ms)
7
8

Enter Enter
End End
Handshaking Protocol
*None
ACK/NAK
RTS/CTS
Xon/Xoff
Scan Mode
Tigger On/Off
Continuous/Tigger Off
Continuous/LED always On
Flash On
*Tigger On/Good read off
Testing
Continuous/Timeout Off
Continuous/No Tigger
9 10

Enter Enter
End End
Buzzer set-up
Frequency (Default：0AH)
Appendix A (00-10H)
Adjust Buzzer Tone (Default：05H)
Appendix A (00-10H)
Power On Tone
ON
OFF
Good read Beep
*ON
OFF
The preamble and postamble character: You can put 10 ASCII
at most in front of the barcode data. When the installation is
“0” that means you don’t need to add the first and last character.
Please find the format as below
The process for adding the first and last character to the bar- code:
1. Scan the barcode of “Start Configuration” and “The
Preamble Character Installation”.
2. Check the ASCII table to get the ASCII code of the first and
last character.
3. Scan the barcode of ASCII in the Appendix.
4. Scan the “End Configuration”.
The Preamble Installation (Default：00)
Appendix A
The Postamble Installation (Default：00)
Appendix A
Character Installation
You can pitch the buzzer tone and adjust the buzzer time
Besides, you can the voice of boot and decoding
11 12

Enter Enter
End End
1. Scan the barcode of the “Start Configuration” and “G1
Insert Character”.
2. Check the ASCII table to get the ASCII code of the first and
last character.
3. Scan the barcode of ASCII in the Appendix.
4. Scan the “End Configuration”.
5. Repeat the same process to the G2 insertion.
6. Scan the “End Configuration”.
G1 Character Insertion （ Default ： 00 ）
Appendix A
G 2 Character Insertion （ Default ： 00 ）
Appendix A
1. Scan the barcode of the “Start Configuration” and “G1
character insertion position”
2. Check the ASCII table to get the corresponding ASCII
code of the insertion position.
3. Scan the “End Configuration”.
4. Repeat the same process to the G2 character insertion
position.
5. Scan the “End Configuration”.
G1 Character Insertion Position （ Default ： 00 ）
Appendix A
G 2 Character Insertion Position （ Default ： 00 ）
Appendix A
Code ID Transmission
ON
*OFF
13 14

Enter Enter
End End
Other Installation
Scanning Verify
*Single
Double
Bar / Space Setting
*Bar = High
*Bar = Low
Laser Data Speed Up
*On
Off
UPC-A
Reading
*On
Off
Code ID (Default：F)
20H-7EH
UPC-A convert to EAN-13
On
*Off
Transmit Check Character
*On
Off
Truncate Leading Zero
On
*Off
BAR-CODE INSTALLATION
15 16

Enter Enter
End End
Truncate Leading Digit (Default：00)
00H-0DH
Truncate Last Digit (Default：00)
00H-0DH
Select Insertion (Default：00)
00H-02H
Add-On 2/5
2 digit
5 digit
2 or 5 digit
*None
UPC-E
Reading
*On
Off
Code ID (Default：G)
20H-7EH
UPC-E convert to UPC-A
On
*Off
Transmit Check Character
*On
Off
Truncate Leading Zero
*On
Off
17 18