Dura Faucet DF-NMK301 User manual

Dura Faucet Limited Lifetime Warranty
Dura Faucet products have been manufactured under the highest standards of
quality and workmanship. Dura Faucet warrants to the original purchaser for as long
as the original purchaser owns their RV that this product will be leak- and drip-free
during normal use, and that all parts and finishes of this product will be free from
defects in material and manufacturing workmanship. Plated metal and plated plastic
finishes are warranted for (1) year.
If the product should develop a leak or drip during the warranty period, Dura Faucet
will, free of charge, provide the parts necessary to put the product back into good
working condition by you. They may also replace any part or finish that proves
defective in material and manufacturing workmanship, under normal installation,
use and service, free of charge. Proof of purchase (original sales receipt) from the
original purchaser must accompany all warranty claims. Defects or damages
caused by the use of other products or parts is not covered by this warranty. If
repair or replacement is not practical, Dura Faucet may elect to refund the purchase
price in exchange for the return of the product.
This warranty covers replacement of all defective parts and finishes. However,
damage due to product abuse, product misuse, installation error, or the use of
cleaners containing alcohol, abrasives, or other solvents, whether performed by a
contractor, service company, or yourself, will void this warranty. Dura Faucet will
not be responsible for labor charges and/or damages incurred in installation, repair
or replacement, nor any indirect, incidental or consequential damages, losses, or
injury costs of any nature relating to this product. Except as provided by law, this
warranty is in lieu of and excludes all other warranties, conditions and guarantees,
whether expressed or implied, statutory or otherwise, including without restriction
those of merchantability or of fitness for use.
Dura Faucet will advise you on how to proceed in making warranty claims. To begin
a warranty claim, write to Dura Faucet explaining the defect and include proof of
purchase and your name, address and telephone number. Email is
[e-mail].
* Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes,
alcohol, solvents or other products not recommended for plated metal or plastic
finishes. This will void the warranty.
19215 SE 34th St. Ste. 106-382
Camas, WA 98607
DF-NMK301 – Designer Single Pedestal
Goose Neck RV Kitchen Faucet

INSTALLATION OF THE FAUCET
1 Remove Mounting Nuts
Remove the mounting nut (10) and
washers (8 & 9) from threaded collar of
the spout (6). Remove the mounting nut
(5) and nylon washer (4) from the threaded
collar of the body (2). Note that the black
rubber gasket (3 & 7) at the base of the
faucet body (2) and spout (6) remains in
place to create a seal after the faucet is
installed.
2 Install Faucet Spout
Install the faucet spout (6) through the
hole in the sink. Slide washers (8 & 9) to
the threaded collar followed by the
mounting nut (10). Thread the mounting
nut to the underside of the sink and
tighten.
3 Install Faucet Body
Install the faucet body (2) through the hole
in the sink. Slide the nylon washer (4) up
to the threaded collar followed by the
mounting nut (5). Thread the mounting nut
to the underside of the sink but do not
tighten yet.
4 Position Faucet Body
Determine the direction you would like the
handle to face when in the off (down)
position. Generally, when installed in the
center of the sink, this would be straight
forward and when installed in the corner,
it would be positioned diagonally across
the sink. Center the faucet through the
hole in your sink and then hold the faucet
body (2) in place. Tighten the mounting
nut until the faucet is secure being careful
not to over tighten.
5 Connect Hoses
Connect the spout supply (13) to the
faucet spout. After doing so, connect the
hot water supply to the longer of the two
flexible supply hoses and the cold water
supply to the shorter. Flexible supply
hoses are complete with ½-inch I.P.S.
fittings for your convenience. We have
also included nose cone washers and
brass supply nuts for use with copper
tubing.
6 Remove Aerator and Check
Water Connections
Remove the aerator from the end of the
spout and run the water for 30 to 60
seconds to flush the lines. While doing
this check to ensure that all of the
connections are tight and there are no
leaks. Reinstall aerator.
MAINTENANCE AND CLEANING
Cleaning Tips: The finish on your product
is designed to retain its beautiful sheen
for years. To maintain the original look of
the finish, a little care and caution should
be used. We recommend the use of mild
soap and water to clean the product.
THE USE OF ABRASIVE CLEANERS MAY
SCRATCH THE FINISH OR CAUSE
OTHER DAMAGE.
RECOMMENDED TOOLS AND
MATERIALS
¨ Adjustable Wrench
¨ Plumbers Tape (Thread Seal
Tape)
¨ Phillips Screw Driver
BEFORE YOU BEGIN
There are a variety of things to do before
installing any new plumbing system into
your home or residence. Before you begin
work make sure you:
¨ Shut off the main water supply
¨ Cover your drain to prevent
loss of parts
¨ Observed any local plumbing
codes
¨ Inspect fixture for damage -
Replace as necessary
Dura Faucet reserves the right to make
any revisions in the design of products
without notice.