DURASTAR DRPTACWS User manual

SLEEVE HARDWARE
ITEM DESCRIPTION DIMENSIONS
1BOTTOM COVER
TOP COVER
LEFT COVER
RIGHT COVER
SEAL A
SEAL B
LONG SCREW
1
2 1
3
4
1
1
126 3
⁄8”
1 5
⁄8”
1
SLEEVE ASSEMBLY (CONTINUED)
2
7
56
1. Lift unit level and slide unit into wall sleeve until firmly
The Drain Kit can be installed for back-side drainage
or bottom-side drainage. Follow the instructions for
the desired drainage location.
2. Insert the bent tube into the drain outlet plate and
1. Attach a foam gasket to the drain outlet plate and
These instructions are for reference only. See the
Unit Manual for more detailed instructions.
3 4
5
62
4
7
11
2 6
3
4
2
5
1
66
1
DRAIN OUTLET PLATE
FOAM GASKET WITH DRAIN OUTLET
COVER PLATE
BENT TUBE
STRAIGHT TUBE
SCREWS (#8 x ½”)
DESCRIPTION QTY
ITEM
1236
4 5
1. Open the LEFT COVER and RIGHT COVER as shown below.
2. Install 6 short screws as shown below.
3. Attach the BOTTOM COVER to the LEFT COVER and
4. Turn the SLEEVE as shown below.
The rear of the top
6
9.3
Top of the SLEEVE SEAL A (26 3
/
8”)
The rear of the bottom
SEAL B (1 5
/
8”) Bottom of the SLEEVE
SEAL B (1 5
/
8”)
Install First
SLEEVE ASSEMBLY
SLEEVE ASSEMBLY (CONTINUED)
UNIT INSTALLATION
HOW TO INSTALL THE DRAIN KIT
DRAIN KIT PARTS LIST
SKU: DRPTACWS
Foldable PTAC Wall Sleeve
SHORT SCREW
8 14
QTY
8
5. Attach SEAL A and SEAL B to the SLEEVE in the
DRAIN KIT
INSTALLATION INSTRUCTIONS
Back-Side Drain Installation
Drain Outlet Plate Cover Plate
#8 x 3 ⁄
4“
#8 x 3
⁄8”
41 7
⁄8”x 14 3 ⁄
4“
41 7
⁄8”x 14 3 ⁄
4“
14 3
⁄
4“x 15 7
⁄8”
14 3
⁄
4“x 15 7
⁄8”
WALL SLEEVE ASSEMBLY
INSTRUCTIONS
RIGHT COVER using 8 short screws as shown below.
locations shown below.
against front of wall sleeve and secure with 4 long
screws through the unit flange holes.
cover plate as shown below.
rotate the tube to the proper position as shown
below.

Back-Side Drain Installation (CONTINUED)
Holes of the
cover plate
2- 1/8 3/8 ~1/2
3. Install the tube and drain outlet plate to the outlet
Bottom-Side Drain Installation (CONTINUED)
3. Drill two 1/8” holes in a suitable position of the
4. Attach the tube and drain outlet plate to the bottom
5. Install the two cover plates over the outlets on the
1. Attach a foam gasket to the drain outlet plate and
2. Insert the straight tube into the drain outlet plate as
Bottom-Side Drain Installation
Drain Outlet Plate Cover Plate Cover Plate
located at the back of the sleeve with two screws
and install the cover plate to the other outlet using
two screws as shown below.
NOTE: The drainage tube may be placed on either
side of the sleeve. Before tightening the screws,
make sure the tube’s position will allow the sleeve to
fit through the wall.
cover plates as shown below.
shown below.
bottom of the wall sleeve to line up with the holes of
the drain outlet plate. Then drill one 3/8” ~1/2” hole
in the middle of the two holes as shown below.
of the wall sleeve using two screws. Gently tighten the
screws at the same time to avoid damaging the tube.
back of the sleeve using four screws. Fasten tightly
to avoid leaks.
©2022 Durastar
V1.0 0822