Home Styles 88 5086 95C User manual

Assembly Instructions 2/4
STEP 1
STEP 2
STEP 3
L
L
K
K
K
DE
B
Attach four Casters
underneath Base (L)
with Wood Screws.
(See ‘Arrow’ sticker
indicating front side)
Assemble Front Piece (H1),
(H2) and Front Rail (K).
(See figure 1)
Attach
the
side of unit with Head Cap Bolts.
the assembled unit
to Middle Panel (D) and (E).
Attach Side Panel (B) to
Attach the Back Piece (G), Middle Panel (D)
and Back Piece (G), Middle Panel (E) onto the
Base (L).
GG
DE
H1
H2
Wood Screw
Wood Screw
Head Cap Bolt
Locking Caster
(On Front)
(Figure 1)
IMPORTANT
* Do not tighten up all the bolts until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.

M
STEP 4
STEP 7
Slide Back Panel (F) into place.
Attach Back and Front
Stretcher (I), (J) to the unit
with Head Cap Bolts.
Attach Side Panel (C) to the other
side of unit with Head Cap Bolts.
J
C
I
Attach Gate Leg (M) at the rear
and connect it to the unit with
Wood Screws.
(See figure 2)
FFF
B
R
S
T
QSTEP 5
Attach Side Rack (Q) to Side Panel (B) with
Head Cap Bolts.
Attach Brush Chrome Pipes (T) and Base Rack (S)
to the Side Rack (Q).
Attach Side Rack (R) to the Side Panel (B),
using Head Cap Bolts.
Head Cap Bolt
Head Cap Bolt
Wood Screw
Wood Screw
Head Cap Bolt
C
V
U
U
STEP 6
Attach Handle Arm (U) to Side Panel (C)
with Head Cap Bolts.
Slide the Round Arm (V) into place.
(Figure 2)
Assembly Instructions 3/4

STEP 8
STEP 9
STEP 10
Place Top (A) onto the unit.
and tighten
all Cam Locks as to secure the top with
the body.
Put Cam Locks into the holes of
the Side Panel (B) and (C)
Insert Adjustable Pins into the side
panels at the desired level.
Place Shelf (P).
A
P
WX
N
N
N
O
P
A
B
B
DE
C
C
Turn over Top (A) and put
Cam Lock Screws into the
pre-drilled holes. Tighten up
Cam Lock Screws.
STEP 11
Cover up all holes
with Wood Plugs.
Figure 1 Figure 2
Attach Pull Handles to the
Door (W) and (X) using Machine
Screws. (See figure 1)
Attach the Door (W) and (X) to
Side Panel (B) and (C), slide the
door lift hinges into the side panel
lift hinges. (See figure 2)
Slide the Drawers (N) and (O)
into place.
Cam Lock Screw
Cam Lock
Assembly Instructions 4/4

88 5086 95C
Drawer (N)
Assembly Instructions
N3.
Side Part
1 pc. for each
drawer.
N4.
Side Part
1 pc. for each
drawer.
N5.
Base Part
1 pc. for each
drawer.
N2.
Back Part
1 pc. for each
drawer.
N2
N2
N5
N5
N3
N4
N4
N4
N3
N3
N1
N1
N1
Assemble the Pull Handle
with Machine Screw on
the Front Part (N1).
(Figure 1)
(Figure 2)
(Figure 3)
HARDWARE LIST
Pull Handle
3 pcs.
Machine Screw
for Pull Handle
6 pcs.
Wood Screw (short)
for base part
18 pcs.(+1 extra)
Wood Screw (long)
for side part
24 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws
into the pre-drilled holes on Base Part
(N5), then tighten all screws.
”
make sure roller
is on the back
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
N1.
Front Part
1 pc. for each
drawer.
N1
Slide the Plywood Base Part (N5) into
the grooves on Side Parts (N3) and (N4).
Be sure to push the plywood all the way
forward so it meets the Front Part (N1).
(See the figure 2)
Unfinished Side
UNIT PART LIST
Using a ,
insert 1 screws into the pre-drilled
holes as shown, tighten half way.
(See the figure 1)
philips screwdriver
”

88 5086 95C
Drawer (O)
O3.
Side Part
1 pc. .
O5.
Base Part
1 pc.
O2.
Back Part
1 pc. .
O2
O2
O5
O5
O3
O4
O4
O4
O3
O3
O1
O1
O1
Assemble the Pull Handle
with Machine Screw on
the Front Part (O1).
(See the figure 4)
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
HARDWARE LIST
Pull Handle
1 pcs.
Machine Screw
for Pull Handle
2 pcs.
Wood Screw (short)
for base part
6 pcs.(+1 extra)
Wood Screw (long)
for side part
8 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws
into the pre-drilled holes on Base Part
(O5), then tighten all screws
(See the figure 3)
”
make sure roller
is on the back
* If you are missing any of these parts,
please contact our DMI Customer
Service Department at 1-877-831-0319
or fax us at 1-800-755-2878.
O1.
Front Part
1 pc.
Slide the Plywood Base Part (O5) into
the grooves on Side Parts (O3) and (O4).
Be sure to push the plywood all the way
forward so it meets the Front Part (O1).
(See the figure 2)
Unfinished Side
O4.
Side Part
1 pc.
O1
UNIT PART LIST
Using a ,
insert 1 screws into the pre-drilled
holes as shown, tighten half way.
(See the figure 1)
philips screwdriver
”
Assembly Instructions