Home Styles 88521695 C User manual

Part List
Hardware List
B.
Side Frame
1 pc.
A.
Top
1 pc.
Hex Wrench
1 pc.
Caster
Two casters with lock
Two casters without lock
4 pcs.
Machine Screw
for Pull Handle
4 pcs.
Pull Handle
2 pc.
Head Cap Bolt
19 pcs. (+1Extra)
Wood Screw
Short 6 x ½”
(for Drawer Bottom Part)
12 pcs.(+1 Extra)
Wood Plug
13 pcs.
(+1 Extra)
Wood Screw
Long 6 x 1”
(for Drawer Side Part)
16 pcs.(+1 Extra)
Tools Required For Assembly : Philips screwdriver
Attention!
Our customers will always get the perfect products,
if they strictly follow the assembly instructions.
Thank you for purchasing our quality products.
D.
Front Rail
2 pcs.
E.
Back Rail
1 pc.
F.
Divider
1 pc.
H.
Shelf
1 pc.
I.
Drawer
(Knock-Down Construction, please refer to
the page (4/4) of these instructions for
steps to complete assembling drawers)
2 drawers
C.
Side Frame
1 pc.
Head Cap Bolt (short)
(for Side Bar)
2 pcs. (+1 Extra)
G.
Base
1 pc.
J.
Side Bar
1 pc.
88521695 C
Solid Wood Top Kitchen Island
Supporting Pin
4 pcs. (+1 Extra)

IMPORTANT
Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as
you may need to tighten up the Head Cap Bolts in the future.
STEP 1
STEP 2
STEP 3
E
D
D
D
F
Attach the Divider (F) and another
Front Rail to the assembled unit.
Attach the Front Rail (D)
and Back Rail (E) to the
Side Frame (B).
Assembly Instructions 2/4
B
B
Turn the Side Frame (B) upside down
on the soft material.
Attach the locking caster to the leg with sign,
and the non-locking caster to the other leg.
Do the same for the Side Frame (C).
Head Cap Bolt
Locking Caster
Non-Locking Caster
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt

Assembly Instructions 3/4
STEP 4
STEP 5
STEP 7
STEP 6
Cover all holes with Wood Plugs
Attach the Base (G)
and Side Frame (C)
to the assembled unit.
Attach the Side Bar (J)
to the Side Frame (C).
C
C
J
A
II
H
G
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt (short)
Head Cap Bolt
Supporting Pins Supporting Pins
Place the Top (A) on the assembled unit.
Insert the Supporting Pins into
both side frames at the desired level.
Place Shelf (H) and slide the Drawers (I)
into place.

Assembly Instructions 4/4
Slider Wheel
I2
I3
I4 I1
I1
Figure 1
Line up Side Parts (I3) and (I4) to the
Front Part (I1) and Back Part (I2). Make sure
the sign on each part is going down.
Using a Philips screwdriver, insert 1” screws
into each of the 4 pre-drilled holes on the
sides (I3) and (I4), then tighten half way.
Drawer
Part List
I1.
Front Part
2pcs.
I5.
Bottom Part
2 pcs.
I2.
Back Part
2 pcs.
Figure 2
Figure 3
Turn the assembled drawer over and slide the
Plywood Bottom Part (I5) into the grooves
of Side Parts (I3) and (I4). Be sure to push
the plywood bottom part all the way forward,
so it meets the Front Part (I1).
Insert the remaining ½” screws (6 pcs.)
into the pre-drilled holes at the Bottom Part
(I5), then tighten up all screws
I4
I2
I5
I1
I3
I3.
Side Part
2 pcs.
I4.
Side Part
2 pcs.
Assemble the Pull Handle
to the Front Part (I1)
with Machine Screw.
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.