West Elm Plinth User manual

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 1 of 9
Plinth Bed
assembl instructions
! Do not throw awa an of the packaging materials until the assembl is complete.
! To protect the finish, assemble this item on a soft surface, such as cardboard or carpet.
! Proper assembl of this item requires 2 people.
CARE INSTRUCTIONS:
Hardware ma loosen over time. Periodicall check that all connections are tight. Wipe with a soft, dr cloth. To
protect the finish, avoid the use of chemicals and household cleaners. All hot serving dishes should be placed on a
trivet or pad. An liquid spilled onto the table should be cleaned up immediatel with a damp cloth.

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 2 of 9
Plinth Bed
assembl instructions
A
Footboard
1x
B
Headboard
1x
C1
Side Rail Right
1x
C2
Side Rail Left
1x
D
Long Apron
2x
E
Short Apron Right
2x
F
Short Apron Left
2x
G
Divider
2x
H
Center Support Rail
(Not Required for Full bed)
1x
I
C
enter Support Leg
(Not Required for Full bed)
3x
J
C
enter Top Panel
(Full bed has 1pc onl )
2x
K
Side Top Panel
2x
Parts
:

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 3 of 9
Plinth Bed
assembl instructions
PARTS:
L
Allen Ke 1x
M
Bolt M6x80mm 22x
N
Bolt M6x30mm 26x
O
Spring Washer (M6) 48x
P
Flat Washer (M6) 48x
1. Attach Long Apron (D) to Footboard (A). Insert Bolt (M) with Washers (O&P) to secure with the
supplied Allen Ke .
5X

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 4 of 9
Plinth Bed
assembl instructions
2. Attach the remaining Long Apron (D) to Headboard (B). Insert Bolt (M) with Washers (O&P) to secure
with the supplied Allen Ke .
5X

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 5 of 9
Plinth Bed
assembl instructions
3. Attach Short Apron Left/Right (E&F) to each Side Rail (C1 & C2). Insert Bolt (M) with Washers (O&P) to
secure with the supplied Allen Ke .
12
X

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 6 of 9
Plinth Bed
assembl instructions
4. Connect Headboard (B) and Dividers (G) to one assembled Side Rail with Bolt (N) and Washers (O&P).
Then attach the other assembled Side Rail to the Headboard and Dividers with Bolt (N) and Washers
(O&P). Secure with the supplied Allen Ke .
16X
2X
cleat

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 7 of 9
Plinth Bed
assembl instructions
5. Attach Footboard (A) to the assembled piece. Insert Bolt (N) with Washers (O&P) to secure with the
supplied Allen Ke .
NOTE: FOR FULL SIZED BED, SKIP TO STEP#8.
6. Align the Center Support Legs (I) to the Center Support Rail (H) as shown and screw them into place b
turning them clockwise. DO NOT OVERTIGHTEN!
6X

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 8 of 9
Plinth Bed
assembl instructions
7. Attach the Center Support Rail with Legs to cut-outs on the Headboard/Footboard and Dividers.
Adjust levelers to keep bed level when needed. Insert Bolt (N) with Washers (O&P) to secure to
headboard and footboard with the supplied Allen Ke .
2X

5413989, 5414052, 5442798, 5442806, 5442814, 5442822 – 09.17 .16 Page 9 of 9
Plinth Bed
assembl instructions
8. Place Top Panels (J&K) onto the bed platform as shown below.
FULL BED
UEEN/KING BED