Duratrax Li-24 User manual

AC Input: 100-240V AC 60Hz, U.S. plug
Output Power: 20W
Battery Types: 2-4S LiPo/LiFe
Fast Charge Start: Auto start at hook up
Fast Charge Current: 1A, 2A, 3A*
Controls: Auto-start, switchable current
selector
Output Connections: 4mm banana sockets
Display Type: 4 red cell LEDs and
1 multi-colored status LED
Balancing Connector: ElectriFly®style 2-4S
Dimensions: 4.4 x 2.7 x 1.6 in.
(111 x 69 x 41mm)
Weight: 6.2 oz (176 g)
2S-4S LiPo/LiFe Balancing Charger
INSTRUCTION
MANUAL
DTXP4620
The Li-24 LiPo/LiFe balancing charger is the perfect entry-level charger for modelers using up to 4S LiPo batteries.
Inexpensive and very easy to operate, the Li-24 utilizes the CC/CV charge method, with voltages customized for LiPo/
LiFe batteries. Capable of operating from 100-240V AC or input sources, this tiny, lightweight charger is perfect for use at
home or in the field. Selectable charge currents range from 1A to 3A and a built-in balancing function ensures all cells are
charged to optimum voltage every time.
It is strongly recommended to read this manual completely before use! Damage resulting
from misuse or modification will void your warranty.
WARNING!! Charging lithium-based rechargeable batteries poses a risk of FIRE! NEVER
treat lithium-based batteries in the same manner as other battery types. NEVER leave
lithium batteries unattended while being charged! ALWAYS charge lithium-based batteries
in a fireproof location! Failure to follow all care and handling instructions contained in
this manual could result in quick, severe, permanent damage to the batteries and all
surroundings!! Follow all safety precautions when using such batteries, as listed on
page 3 of this manual!
®
1
SPECIFICATIONS
*Note: Maximum charge current for a 4S pack will be ~1.4A.
SPECIAL FEATURES
●Built-in balancing for 2-4S LiPo.
●1A, 2A, 3A selectable charge rates.
●Select between LiPo and LiFe battery type.
●Built in balancing connector for 2S, 3S and 4S.
●Includes Deans®Ultra Plug®connector* and 18AWG
charging cable with 4mm banana plugs included.
●Built in 4mm banana battery sockets.
●Reverse voltage protection.
LED ACTIVITY
LED blinking green The charger is ready to charge.
LED
CHARGE
STATUS LED
CELL
STATUS LED
DefinitionIndication
LED glows constant orange The charger is charging in CV mode.
LED glows constant red The cell is charging.
LED flashes red The cell is discharging.
LED glows constant green The charging process is finished.
LED glows red The charger is charging in CC mode.
Charge LED + Cell 1LED Voltage difference among cells is too large (>300mV).
Charge LED + Cell 3LED Over current protection.
Charge LED + Cell 4LED Reverse polarity.
Charge LED + Cell 2LED Wrong connection.
ERROR CODES
If there is an error, the
charge status LED and one
of the cell LEDs will blink in
sequence. Unplug the power
cord and disconnect battery.
HEAT VENTILATION
Vents built into the case allow hot air to escape to help keep the electronic
circuitry cool. This helps to maintain accurate operation and maximize the
lifespan of the charger itself.
OPTIONAL ACCESSORIES
1-YEAR LIMITED WARRANTY - *U.S.A. and CANADA ONLY
Duratrax warrants this product to be free from defects in materials and workmanship for a period of one (1) year from
the date of purchase. During that period, Duratrax will, at its option, repair or replace without service charge any product
deemed defective due to those causes. You will be required to provide proof of purchase (invoice or receipt). This warranty
does not cover damage caused by abuse, misuse, alteration or accident. If there is damage stemming from these causes
within the stated warranty period, Duratrax will, at its option, repair or replace it for a service charge not greater than 50%
of its then current retail list price. Be sure to include your daytime telephone number in case we need to contact you about
your repair. This warranty gives you specific rights. You may also have other rights, which vary from state to state.
For service on your Duratrax product, warranty or non-warranty, send it post-paid and insured to:
For service on your Duratrax product if purchased in the U.S.A.
or Canada, send it postpaid and insured to:
HOBBY SERVICES
3002 N. Apollo Dr., Suite 1
Champaign, IL 61822
Tel: [phone] (9:00am - 5:00pm CST, M-F)
E-mail: [e-mail]
For service on your Duratrax product if purchased in the
European Union, send it postpaid and insured to:
Service Abteilung Revell GmbH
Henschelstrasse 20-30
32257 Bünde Germany
Tel: [phone] (nur für Deutschland)
Email: [e-mail]
*For warranty and service information if purchased outside the USA or Canada, see the additional warranty information
insert (if applicable) or ask your retailer for more information.
Conforms to FCC part 15B standards.
© 2013 Hobbico Inc. •Made in China •DTXP4620 v1.2
4
DTXC2223
Charge Lead Banana
Plugs to Mini Plug
DTXC2222
Charge Lead Banana
Plugs to Traxxas®
DTXC2220
Charge Lead Banana Plugs
to Standard
*Deans and Ultra Plug are registered trademarks of W.S. Deans Co. U.S. Patent No. 5,533,915.

IMPORTANT PRECAUTIONS
●Do not leave the charger unattended while in use.
●Disconnect the battery and remove input power from the charger immediately if the charger
or battery becomes hot!!
●Disconnect the battery if it begins to swell while being charged!
●Do not attempt to charge any battery types other than LiPo and LiFe as permanent damage to the battery and charger
could result.
●Do not allow water, moisture or foreign objects into the charger.
●Do not block the air intake holes, which could cause the charger to overheat.
●Do not attempt to use batteries with more cells or total voltage than listed in the specifications.
●Do not place the charger or battery on flammable surfaces or near combustible materials while in use, such as carpet,
cluttered workbench, paper, plastic, vinyl, leather, and wood, inside an R/C model or full sized automobile.
●Allow the charger and battery to cool down between charges.
●Always disconnect the charger from its power source when not in use.
GLOSSARY OF TERMS
Amps (A): The unit of measure for charge current.
Milli-amps (mA): A unit of measure for current, being 1/1000 of an amp (.001A). So 2500mA is the same as 2.5A
(2.5 1000). Or, to convert amps to milli-amps, multipy the A number by 1000. So .025A is the same as 25mA.
Capacity and milli-amp hours (mAh): The amount of energy a battery can store is called its capacity, which is defined
as how much current a battery can supply constantly over one hour of time. Most hobby batteries are rated for capacity
in “mAh” or milli-amp hours. A 650mAh battery can deliver 650mA of current for one hour (650mA 1hr = 650mAh). A
3200mAh battery can deliver 3200mA (3.2A) of current for one hour (3200mA 1hr = 3200mAh), etc.
CC/CV: Lithium based batteries are charged using the “Constant Current/Constant Voltage” method (cc/cv). Constant
current is delivered during the first part of the charge. When the battery reaches a pre-set voltage, constant current is no
longer delivered and a constant voltage is applied to the battery. As the battery’s voltage becomes equalized to the voltage
on the charger’s output, charge current will steadily begin to drop. This is normal. When current reaches an approximate
value of 1/10C, the charge process will end completely.
“C” rating: Capacity is also referred to as the “C” rating. Some battery suppliers recommend charge currents based on the
battery’s “C” rating. A battery’s “1C” current is the same number as the battery’s rated capacity number, but noted in mA or
amps. A 600mAh battery has a 1C current value of 600mA, and a 3C current value of (3 600mA) 1800mA or 1.8A. The
1C current value for a 3200mAh battery would be 3200mA (3.2A), etc.
INPUT POWER
AC Input: For indoor use, connect the AC power cord
to a 110V-240V AC outlet.
The charger will be on at all times when connected
to input power. Disconnect the charger from input
power when not in use.
CONTROLS
2
CARE AND HANDLING OF LiPo/LiFe BATTERIES
WARNING!! DO NOT try to charge lithium-polymer (LiPo) or lithium-ferrite (LiFe) cells in the same
way as other battery types! Always read the instructions that are included with your lithium batteries
carefully before use. Failure to follow these care and handling instructions can quickly result in
severe, permanent damage to the batteries and their surroundings and even start a FIRE!
● ALWAYS charge lithium batteries in a fireproof location, which could be a container made of metal or ceramic tile.
Monitor the area with a smoke or fire alarm, and have a lithium approved fire extinguisher available at all times.
●ALWAYS use a LiPo charge bag when charging lithium batteries, such as the Great Planes®SafeCharge™LiPo
Battery Charge Bag (GPMP0751).
●NEVER attempt to extinguish a lithium fire with water or a non-lithium approved fire extinguisher! Use ONLY a
“Class D” fire extinguisher.
●ALWAYS provide adequate ventilation around LiPo/LiFe batteries during charge, while in use, and during storage.
●NEVER allow LiPo/LiFe cells to overheat at any time, as they can and usually will become physically damaged and
could possibly EXPLODE or catch FIRE!! If a battery becomes overheated (over 140°F, 60°C), disconnect it from
the charger IMMEDIATELY!
●NEVER continue to charge LiPo/LiFe batteries if the charger fails to recognize full charge. LiPo/LiFe cells which
swell or emit smoke may be in an overcharge condition and should be disconnected from the charger immediately.
●NEVER charge LiPo/LiFe batteries at currents greater than the maximum rated current as specified by the battery’s
manufacturer.
●NEVER allow LiPo/LiFe cells to come in contact with moisture or water at any time.
●NEVER allow the internal electrolyte from LiPo/LiFe batteries to get in the eyes or on skin – wash affected areas
immediately if they come in contact with the electrolyte and contact your physician!
●ALWAYS keep lithium batteries away from children.
DETERMINING BATTERY SPECIFICATIONS
Always read your battery’s label and/or
instruction sheet before use. Check to
determine how many cells it contains or its
nominal rated voltage. The chart at right
is a quick reference for determining this
information.
STARTING CHARGE
1. Insert the AC power cord into the charger.
2. Insert the AC cord into a wall socket (100 – 240V). All LEDs will light for 1 second and the charge status LED will flash
green which indicates the charger is ready to charge.
3. Select the battery type LiPo/LiFe by the toggle switch.
4. Select the proper charging current 1A/2A/3A by the toggle switch.
5. Connect the battery main charge lead to the battery socket which is in the front side of the charger. Connect the battery
balance wire to the balance port, which is in the right side of the charger.
6. The charger will start charging. The charge status LED and the cell status LED will glow constant red. If the battery
pack is 2-cell, cell 1 and cell 2 LEDs will glow constant red. If the battery pack is 3-cell, cell 1, cell 2, and cell 3 will
glow constant and so on.
7. During the charging process, when the charge LED glows constant red, the charger is charging in constant current
mode. When the charge LED glows constant orange, the charger is in constant voltage mode.
8. When the cell LED is flashing, the cell is discharging for balancing.
9. When the battery is fully charged, the charge status LED will glow constant green.
10. Unplug the battery from the charger and charger status LED will flash green which indicates the charger is ready to
charge another battery.
1S
2S
3S
4S
3.3 V
6.6 V
9.9 V
13.2 V
Voltage Chart
Number of Cells LiFe Nominal Voltage
3.7 V
7.4 V
11.1 V
14.8 V
LiPo Nominal Voltage
3
d
AC 100-240V Power Jack
Cell 1 LED Indicator
Cell 2 LED Indicator Cell 3 LED Indicator
Cell 4 LED Indicator
Charge Current Switch
Battery Type Switch
Battery Socket
Charge Status LED Indicator
Balance Sockets

IMPORTANT PRECAUTIONS
●Do not leave the charger unattended while in use.
●Disconnect the battery and remove input power from the charger immediately if the charger
or battery becomes hot!!
●Disconnect the battery if it begins to swell while being charged!
●Do not attempt to charge any battery types other than LiPo and LiFe as permanent damage to the battery and charger
could result.
●Do not allow water, moisture or foreign objects into the charger.
●Do not block the air intake holes, which could cause the charger to overheat.
●Do not attempt to use batteries with more cells or total voltage than listed in the specifications.
●Do not place the charger or battery on flammable surfaces or near combustible materials while in use, such as carpet,
cluttered workbench, paper, plastic, vinyl, leather, and wood, inside an R/C model or full sized automobile.
●Allow the charger and battery to cool down between charges.
●Always disconnect the charger from its power source when not in use.
GLOSSARY OF TERMS
Amps (A): The unit of measure for charge current.
Milli-amps (mA): A unit of measure for current, being 1/1000 of an amp (.001A). So 2500mA is the same as 2.5A
(2.5 1000). Or, to convert amps to milli-amps, multipy the A number by 1000. So .025A is the same as 25mA.
Capacity and milli-amp hours (mAh): The amount of energy a battery can store is called its capacity, which is defined
as how much current a battery can supply constantly over one hour of time. Most hobby batteries are rated for capacity
in “mAh” or milli-amp hours. A 650mAh battery can deliver 650mA of current for one hour (650mA 1hr = 650mAh). A
3200mAh battery can deliver 3200mA (3.2A) of current for one hour (3200mA 1hr = 3200mAh), etc.
CC/CV: Lithium based batteries are charged using the “Constant Current/Constant Voltage” method (cc/cv). Constant
current is delivered during the first part of the charge. When the battery reaches a pre-set voltage, constant current is no
longer delivered and a constant voltage is applied to the battery. As the battery’s voltage becomes equalized to the voltage
on the charger’s output, charge current will steadily begin to drop. This is normal. When current reaches an approximate
value of 1/10C, the charge process will end completely.
“C” rating: Capacity is also referred to as the “C” rating. Some battery suppliers recommend charge currents based on the
battery’s “C” rating. A battery’s “1C” current is the same number as the battery’s rated capacity number, but noted in mA or
amps. A 600mAh battery has a 1C current value of 600mA, and a 3C current value of (3 600mA) 1800mA or 1.8A. The
1C current value for a 3200mAh battery would be 3200mA (3.2A), etc.
INPUT POWER
AC Input: For indoor use, connect the AC power cord
to a 110V-240V AC outlet.
The charger will be on at all times when connected
to input power. Disconnect the charger from input
power when not in use.
CONTROLS
2
CARE AND HANDLING OF LiPo/LiFe BATTERIES
WARNING!! DO NOT try to charge lithium-polymer (LiPo) or lithium-ferrite (LiFe) cells in the same
way as other battery types! Always read the instructions that are included with your lithium batteries
carefully before use. Failure to follow these care and handling instructions can quickly result in
severe, permanent damage to the batteries and their surroundings and even start a FIRE!
● ALWAYS charge lithium batteries in a fireproof location, which could be a container made of metal or ceramic tile.
Monitor the area with a smoke or fire alarm, and have a lithium approved fire extinguisher available at all times.
●ALWAYS use a LiPo charge bag when charging lithium batteries, such as the Great Planes®SafeCharge™LiPo
Battery Charge Bag (GPMP0751).
●NEVER attempt to extinguish a lithium fire with water or a non-lithium approved fire extinguisher! Use ONLY a
“Class D” fire extinguisher.
●ALWAYS provide adequate ventilation around LiPo/LiFe batteries during charge, while in use, and during storage.
●NEVER allow LiPo/LiFe cells to overheat at any time, as they can and usually will become physically damaged and
could possibly EXPLODE or catch FIRE!! If a battery becomes overheated (over 140°F, 60°C), disconnect it from
the charger IMMEDIATELY!
●NEVER continue to charge LiPo/LiFe batteries if the charger fails to recognize full charge. LiPo/LiFe cells which
swell or emit smoke may be in an overcharge condition and should be disconnected from the charger immediately.
●NEVER charge LiPo/LiFe batteries at currents greater than the maximum rated current as specified by the battery’s
manufacturer.
●NEVER allow LiPo/LiFe cells to come in contact with moisture or water at any time.
●NEVER allow the internal electrolyte from LiPo/LiFe batteries to get in the eyes or on skin – wash affected areas
immediately if they come in contact with the electrolyte and contact your physician!
●ALWAYS keep lithium batteries away from children.
DETERMINING BATTERY SPECIFICATIONS
Always read your battery’s label and/or
instruction sheet before use. Check to
determine how many cells it contains or its
nominal rated voltage. The chart at right
is a quick reference for determining this
information.
STARTING CHARGE
1. Insert the AC power cord into the charger.
2. Insert the AC cord into a wall socket (100 – 240V). All LEDs will light for 1 second and the charge status LED will flash
green which indicates the charger is ready to charge.
3. Select the battery type LiPo/LiFe by the toggle switch.
4. Select the proper charging current 1A/2A/3A by the toggle switch.
5. Connect the battery main charge lead to the battery socket which is in the front side of the charger. Connect the battery
balance wire to the balance port, which is in the right side of the charger.
6. The charger will start charging. The charge status LED and the cell status LED will glow constant red. If the battery
pack is 2-cell, cell 1 and cell 2 LEDs will glow constant red. If the battery pack is 3-cell, cell 1, cell 2, and cell 3 will
glow constant and so on.
7. During the charging process, when the charge LED glows constant red, the charger is charging in constant current
mode. When the charge LED glows constant orange, the charger is in constant voltage mode.
8. When the cell LED is flashing, the cell is discharging for balancing.
9. When the battery is fully charged, the charge status LED will glow constant green.
10. Unplug the battery from the charger and charger status LED will flash green which indicates the charger is ready to
charge another battery.
1S
2S
3S
4S
3.3 V
6.6 V
9.9 V
13.2 V
Voltage Chart
Number of Cells LiFe Nominal Voltage
3.7 V
7.4 V
11.1 V
14.8 V
LiPo Nominal Voltage
3
d
AC 100-240V Power Jack
Cell 1 LED Indicator
Cell 2 LED Indicator Cell 3 LED Indicator
Cell 4 LED Indicator
Charge Current Switch
Battery Type Switch
Battery Socket
Charge Status LED Indicator
Balance Sockets

AC Input: 100-240V AC 60Hz, U.S. plug
Output Power: 20W
Battery Types: 2-4S LiPo/LiFe
Fast Charge Start: Auto start at hook up
Fast Charge Current: 1A, 2A, 3A*
Controls: Auto-start, switchable current
selector
Output Connections: 4mm banana sockets
Display Type: 4 red cell LEDs and
1 multi-colored status LED
Balancing Connector: ElectriFly®style 2-4S
Dimensions: 4.4 x 2.7 x 1.6 in.
(111 x 69 x 41mm)
Weight: 6.2 oz (176 g)
2S-4S LiPo/LiFe Balancing Charger
INSTRUCTION
MANUAL
DTXP4620
The Li-24 LiPo/LiFe balancing charger is the perfect entry-level charger for modelers using up to 4S LiPo batteries.
Inexpensive and very easy to operate, the Li-24 utilizes the CC/CV charge method, with voltages customized for LiPo/
LiFe batteries. Capable of operating from 100-240V AC or input sources, this tiny, lightweight charger is perfect for use at
home or in the field. Selectable charge currents range from 1A to 3A and a built-in balancing function ensures all cells are
charged to optimum voltage every time.
It is strongly recommended to read this manual completely before use! Damage resulting
from misuse or modification will void your warranty.
WARNING!! Charging lithium-based rechargeable batteries poses a risk of FIRE! NEVER
treat lithium-based batteries in the same manner as other battery types. NEVER leave
lithium batteries unattended while being charged! ALWAYS charge lithium-based batteries
in a fireproof location! Failure to follow all care and handling instructions contained in
this manual could result in quick, severe, permanent damage to the batteries and all
surroundings!! Follow all safety precautions when using such batteries, as listed on
page 3 of this manual!
®
1
SPECIFICATIONS
*Note: Maximum charge current for a 4S pack will be ~1.4A.
SPECIAL FEATURES
●Built-in balancing for 2-4S LiPo.
●1A, 2A, 3A selectable charge rates.
●Select between LiPo and LiFe battery type.
●Built in balancing connector for 2S, 3S and 4S.
●Includes Deans®Ultra Plug®connector* and 18AWG
charging cable with 4mm banana plugs included.
●Built in 4mm banana battery sockets.
●Reverse voltage protection.
LED ACTIVITY
LED blinking green The charger is ready to charge.
LED
CHARGE
STATUS LED
CELL
STATUS LED
DefinitionIndication
LED glows constant orange The charger is charging in CV mode.
LED glows constant red The cell is charging.
LED flashes red The cell is discharging.
LED glows constant green The charging process is finished.
LED glows red The charger is charging in CC mode.
Charge LED + Cell 1LED Voltage difference among cells is too large (>300mV).
Charge LED + Cell 3LED Over current protection.
Charge LED + Cell 4LED Reverse polarity.
Charge LED + Cell 2LED Wrong connection.
ERROR CODES
If there is an error, the
charge status LED and one
of the cell LEDs will blink in
sequence. Unplug the power
cord and disconnect battery.
HEAT VENTILATION
Vents built into the case allow hot air to escape to help keep the electronic
circuitry cool. This helps to maintain accurate operation and maximize the
lifespan of the charger itself.
OPTIONAL ACCESSORIES
1-YEAR LIMITED WARRANTY - *U.S.A. and CANADA ONLY
Duratrax warrants this product to be free from defects in materials and workmanship for a period of one (1) year from
the date of purchase. During that period, Duratrax will, at its option, repair or replace without service charge any product
deemed defective due to those causes. You will be required to provide proof of purchase (invoice or receipt). This warranty
does not cover damage caused by abuse, misuse, alteration or accident. If there is damage stemming from these causes
within the stated warranty period, Duratrax will, at its option, repair or replace it for a service charge not greater than 50%
of its then current retail list price. Be sure to include your daytime telephone number in case we need to contact you about
your repair. This warranty gives you specific rights. You may also have other rights, which vary from state to state.
For service on your Duratrax product, warranty or non-warranty, send it post-paid and insured to:
For service on your Duratrax product if purchased in the U.S.A.
or Canada, send it postpaid and insured to:
HOBBY SERVICES
3002 N. Apollo Dr., Suite 1
Champaign, IL 61822
Tel: [phone] (9:00am - 5:00pm CST, M-F)
E-mail: [e-mail]
For service on your Duratrax product if purchased in the
European Union, send it postpaid and insured to:
Service Abteilung Revell GmbH
Henschelstrasse 20-30
32257 Bünde Germany
Tel: [phone] (nur für Deutschland)
Email: [e-mail]
*For warranty and service information if purchased outside the USA or Canada, see the additional warranty information
insert (if applicable) or ask your retailer for more information.
Conforms to FCC part 15B standards.
© 2013 Hobbico Inc. •Made in China •DTXP4620 v1.2
4
DTXC2223
Charge Lead Banana
Plugs to Mini Plug
DTXC2222
Charge Lead Banana
Plugs to Traxxas®
DTXC2220
Charge Lead Banana Plugs
to Standard
*Deans and Ultra Plug are registered trademarks of W.S. Deans Co. U.S. Patent No. 5,533,915.