DV Signage MON-100W User manual

Page 1 of 22
Manual
MON-100W
10.2” Monitor
MON-100W : P/N 586845110-3

Table of Contents
1. Introduction
!
3
2. System
4
3. Instruction
3.1 Preparation
6
3.2 Powering On
6
3.3 Signal Input
6
4. Controls
4.1 Button control
7
4.2 OSD menu function
8
4.3 Remote control
10
4.4 Serial control
11
5. Dimensions
12
6. Specification
13
7. Appendix I – Graphic & Video Mode Support Table
14
8. Appendix II – Auto Color Gain
16
9. Serial control protocols
17
10. Warranty, Caution & Limitation of Liability, Trademark
21
11. Contact details
22

Page 3 of 22
1. Introduction
The 10.2” DV Signage widescreen monitor (model: MON-100W) is a single LCD display
unit. The unit provides standard video interfaces (DVI, VGA, S-Video & Composite). The
monitor is fit for control room information display or any other general purpose information
display.
Ordering Information :
Part Number
Model
P/N 586845100-3
MON-100W
P/N 586845110-3
MON-100W (without stand in the package)
If you have difficulties, please contact your sales representative or DV Signage support,
contact details are available on http://www.dvsignage.com/contact-us
IMPORTANT USAGE NOTE
The manufacturer accepts no liability for damage or injury caused by the use of this product.
It is the responsibility of the developer, integrators or other users of this product to:
Ensure that all necessary and appropriate safety measures are taken.
Obtain suitable regulatory approvals as may be required.
Check power settings to all component parts before connection.
DISCLAIMER
There is no implied or expressed warranty regarding this material.

2. System
10.2” Monitor (MON-100W) A robust metal housing with powder coating:
(2)!COM!
Port
(3)!On/Off!
switch
(4)!Status!LED
(7)!S=Video!Input
(9)!DVI=D!Input

Page 5 of 22
Item
Description
Function
1
OSD button
Controlling the OSD menu
function
2
COM port
For serial command control
3
On/Off switch
Power on/off switch of the unit
4
Status LED
Status LED
5
Power in (DC 12V)
DC 12V Power input
6
Composite Video Input
Composite Video Input
7
S-Video Input
S-Video Input
8
Analog RGB Input
Analog RGB Input
9
DVI-D Input
DVI-D Input
10
IR Sensor
IR Sensor

3. Instructions
3.1 Preparation
The DV Signage monitor is designed to be as plug and play as possible requiring the
minimum of setup for use. The following describes the operation of this monitor unit.
Please make sure the whole package in the box includes the items below :
10.2” monitor
Power supply
Power cord
Stand P/N 366845191-3 (only available in P/N 586845100-3)
3.2 Powering On
Connect the provided external AC power supply unit.
Power on the unit using the Power on/off switch, the status LED should come on.
This LED indicates the controller status.
State
Status LED color
No signal & backlight off
RED
No signal & backlight on
ORANGE
With signal & backlight on
GREEN
3.3 Signal input
VGA / DVI / Composite / S-Video input :
- VGA /DVI input : Use suitably shielded cable to be used as this may affect regulatory
emission test results and the image quality displayed. See Appendix I for the mode support
table on VGA & DVI port side.
- Composite / S-Video : Standard Composite or S-video cables can be used. Reasonable
quality cable should be used to avoid image quality degradation. See Appendix I for the
video system support on composite & S-Video port.

Page 7 of 22
4. Controls
Once the system has been connected and switched on there are a number of functions
available to adjust the display image as summarized in the following sections. The settings
chosen will be saved for each mode independently.
4.1 Button control
Controls
Functions
Menu – turns OSD menu On or Off (it will auto time off)
(Function with signal input only)
Menu button
Select – Select function / Confirm
(under OSD menu on state)
DOWN
Move up to select individual RGB color level OSD page
(under OSD menu on state)
UP
+ – increase the setting / moves the selector to the next
function (under OSD menu on state)
+
- - decrease the setting / moves the selector to the previous
function (under OSD menu on state)
-
Load factory default
Press and hold DOWN botton to power
on the controller
Lock OSD menu
(Function with signal input only)
Press and hold MENU button for 15
seconds to enable / disable lock of the
OSD menu
Switch to next input source
(under OSD menu off state)
+

4.2 OSD menu functions
Selection page
Select input source4
Select input source to Analog RGB
Select input source to DVI
Select input source to S-Video 1
Select input source to Composite 1
Select input source to S-Video 2 (No function now)
Select input source to Composite 2 (No function now)
Auto Source Seek
ON – Auto source select always enable
OFF – Disable auto source select function
Video system selection* 4
Select Auto video system detection
Select PAL video system
Select PAL M video system
Select NTSC video system
Select NTSC 4.43 video system
Select SECAM video system
Wide screen mode
information display#
Select the input mode (1280 / 1360 / 1366 / 1368) to recognize and display the correct
input signal information display on the OSD menu.
1280 : 1280x768
1360 : 1360x768
1366 :1366x768
1368 : 1368x768
Exit
Exit the OSD menu and save the settings
Brightness and Contrast
Brightness
Increase/decrease brightness level.
Press – or + (-+ ) Total : 256 steps
Contrast
Increase/decrease panel contrast level.
Press – or + (-+ ) Total : 192 steps
Saturation*
Increase/decrease hue level.
Press – or + (-+ ) Total : 256 steps
Hue*
Increase/decrease saturation level
Press – or + (-+ ) Total : 128 steps
Exit
Exit the OSD menu and save the settings
Color
Auto RGB Calibration#
Yes No (See appendix IV)
Color Temperature 4(Adjust the warmness of the image displayed. The higher temperature the
coolest image looks like. The lower temperature the warmest image looks like.)

Page 9 of 22
Adjust red color level
Press – or + (-+) Total :128 steps
Adjust green color level
Press – or + (-+) Total : 128 steps
Adjust blue color level
Press – or + (-+) Total : 128 steps
Press SEL UP/DN button to select item
Set the color temperature to 4200K
Set the color temperature to 5000K
Set the color temperature to 6500K
Set the color temperature to 7500K
Set the color temperature to 9300K
Gamma adjustment4
Adjust Gamma settings (0.4 / 0.6 / 1.0 / 1.6 / 2.2)
Select Gamma to 0.4
Select Gamma to 0.6
Select Gamma to 1.0
Select Gamma to 1.6
Select Gamma to 2.2
Exit
Exit the OSD menu and save the settings
Position#
Autosetup
Auto adjust the positions, phase, frequency
Yes No
Frequency
Adjust the image horizontal size
Phase
Fine tune the data sampling position (adjust image quality)
Image Horizontal Position
Use +/- to move the image horizontally
Press – or + (-+ )
Image Vertical
Position
Use +/- to move the image vertically
Press – or + (-+ )
Exit
Exit the OSD menu
Utilities
OSD setting 4
OSD Timeout : 0 / 10 / 20 / 30 / 40 / 50 / 60 seconds (Always on when set to 0)
Press – or + (-+ )
OSD menu horizontal position
Press – or + (-+ )
OSD menu vertical position
Press – or + (-+ )
Load Factory Default
Initialize the setting stored in non-volatile memory
Sharpness
Adjust sharpness level
Press – or + (-+ ) Total : 49 steps
Exit
Exit the OSD menu
Exit the OSD menu
* - Function in Video mode only Items marked 4 have sub menus.

# - Function in ARGB mode only Exit the OSD menu to save the setting chosen
4.3 Remote control (Optional)
BUTTON
FUNCTION
POWER BUTTON
Soft power ON/OFF button.
ATTENTION BUTTON
Use combined with digit keys (“Attention” + “1”) to enable/disable the IR function.
SEL UP ( ) / SEL DN (
)
Press this button to select the items in the OSD menu.
+ / - BUTTON
Use “+” button to direct control the hotkey function for switching to next input source.
In OSD menu, pressing this button to adjust the settings.
DISPLAY BUTTON
Activate the OSD menu display on screen.
STOP (RGB) BUTTON
In input source selection mode, pressing this button to select RGB source.
TRACK (S-Vid)
BUTTON
In input source selection mode, pressing this button to select S-Video source.
TRACK (Comp)
BUTTON
In input source selection mode, pressing this button to select Composite source.