DVIGear DVI-4141 User manual
DVI+HDCP 4x1 Switcher
User Manual
DVI-4141
TABLE OF CONTENTS
I. Introduction
II. Package Contents
III. Features
IV. Getting the Best Results
V. Specications
VI. Connecting the Hardware
VII. Operating the Unit
VIII. Troubleshooting
IX. Warranty Information
X. Contact Us
I. INTRODUCTION
Thank you for purchasing this DVI + HDCP 4x1 Switcher from DVIGear.
The DVI-4141 is designed for usage with two sources and a single dis-
play. The device allows for four DVI-enabled sources to be switched to a
single DVI input on a display. The unit is fully HDCP compliant for usage
with sources and displays utilizing this technology.
Prior to using this product, please read this manual in its entirety. Please
feel free to contact us with any questions or comments you may have
regarding the unit or its performance.
II. PACKAGE CONTENTS
• DVI-4141 DVI + HDCP 4x1 Switcher
• DVI-DVI 6ft Cable
• 9VDC AC Power Adapter
• Manual
III. FEATURES
• Ultra Compact, High Performance Unit
• Supports HDCP on both inputs and output
• Supports HDTV resolutions up to 1080p and PC resolutions up to
1920x1200 / 60Hz
• Four DVI (HDCP or non-HDCP) signals can be switched to a single DVI
(HDCP or non-HDCP) display
• Full DDC support
IV. GETTING THE BEST RESULTS
Manyfactorsinuencethequalityofadigitalvideosignalinanyapplica-
tion. When additional interconnects are put into the system, the pos-
sibility for signal degradation arises. Below are some things to keep in
mind in order to ensure the best unit performance:
• Output source device - The quality of the output signal will depend
largely upon the type and quality of source device used. For instance,
some DVD players just perform better than others.
• Using Native Resolution - It is always best to set the output resolu-
tion of the source device to the native resolution and refresh rate of the
display device(s). This allows for the two units to work together in the
best fashion.
• Distance between the source and display devices - The length of cable
between the source(s) and display(s) should be minimized as much as
possible. When using the DVI-4141, the overall cable distance should
notexceed10Mwithoutproperamplication.
• Connection cables - When using the DVI + HDCP 4x1 Switcher, the
highest quality cables should be used. Using DVIGear’s Super High
Resolution DVI cables will ensure the best possible signal between the
source and the display.
• Interference from nearby electrical devices - These can have an ad-
verse effect on signal quality. For example, an older computer monitor
oftenemitsveryhighelectromagneticeldsthatcaninterferewiththe
performance of video equipment in its proximity.
V. SPECIFICATIONS
Performance
HDTV Resolutions
Supported
480i, 480p; 720p; 1080i; 1080p
Computer Resolutions
Supported
All up to 1920x1200 @ 60Hz
Maximum Bandwidth
Supported
165MHz (analog)
Maximum Bitrate
Supported
1.65Gbit/sec
Mechanical
Dimensions (HxWxD)
(mm)
42 x 162 x 72
Weigth (grams) 0.9lbs
Environmental
Operating Temperature 0° to 40° C (32° to 104° F)
Operating Humidity 10% to 85% non-condensing
Accessories Included
9VDC AC Power Adapter
Operations Manual
6ft DVI-DVI Cable
VI. CONNECTING THE HARDWARE
Prior to connecting the unit, ensure that all devices have been
powered off.
1) Connect your DVI display to the switch’s DVI output with a high-
quality cable
2) Connect your four (4) DVI sources to the switch’s inputs using a
high-quality DVI cable.
3) Plug the 9VDC power adapter in to the rear of the unit.
4) Plug the power adapter in to an AC socket.
5) Power on all source and display devices.
V. OPERATING THE UNIT
It is possible to select the input device you wish to access in two ways:
using the front panel push button or via the enclosed remote control
unit.
1) Front Panel Push Button Selection:
• The front panel push button is used to select the source to be dis-
played on the screen. Pressing the button during normal operation will
cause the input devices to be toggled through.
2) Remote Control Selection:
• The input device may selected via the included remote control by
pressing the appropriate button (“1” for the source on input 1 and “2”
for the source on input 2 and so on).
Note:IfyouhaveaproblemwiththeIRcontrolconictingwithother
devices,theremoteallowsuserstocongurefour(A,B,C,D)alternate
combinations of IR codes. To change, press and hold an IR code but-
ton for 2 seconds.
VIII. TROUBLESHOOTING
If the switcher does not appear to be functioning, make certain that all
of the DVI connections are securely attached to the unit with all appro-
priate screws in tight. Secondly, verify the functioning of all DVI devices
(sources and displays) by connecting them with a short (6ft or less) DVI
cable. If the signal is present under those conditions, ensure that the
connections are made fully and that the power indicator light is clearly
lit. Finally, make sure that the overall cable distance does not exceed
10M(approx.33ft)withoutproperamplication.
If the above suggestions are not helpful, please contact us at
support@dvigear.com or by phone at 888-463-9927. For more informa-
tion, please visit our website at http://www.dvigear.com
IX. WARRANTY INFORMATION
DVIGear warrants the equipment it manufactures to be free from
defects in material and workmanship. If equipment fails because of
suchdefectsandDVIGearisnotifiedwithinthreeyearsfromthedateof
shipment, DVIGear will, at its option, repair or replace the equipment,
provided that the equipment has not been subjected to mechanical,
electrical,orotherabuseormodications.Equipmentthatfailsunder
conditions other than those covered will be repaired at the current price
of parts and labor in effect at the time of the repair. Such repairs are
warranted for ninety days from the day of re-shipment to the buyer.
This warranty is in lieu of all other warranties expressed or implied,
including without limitation, any implied warranty or merchantability or
tnessforanyparticularpurpose,allofwhichareexpresslydisclaimed.
The information in this manual has been carefully checked and is be-
lieved to be accurate. However, DVIGear assumes no responsibility for
any inaccuracies that may be contained in this manual. In no event will
DVIGear be liable for direct, indirect, special, incidental, or consequen-
tial damages resulting from any defect or omission in this manual, even
if advised of the possibility of such damages. The technical information
containedhereinregardingtheproductfeaturesandspecicationsis
subject to change without notice.
Your Digital Connectivity Experts
1059 Triad Court
Suite 8
Marietta, GA 30062-2258
Toll Free: 888.463.9927
Phone: 770.421.6699
Fax: 770.234.4207
www.dvigear.com
Table of contents
Other DVIGear Switch manuals
