Dwyer Instruments WD3 Series User manual

Series WD3 Water Leak Detector
Specifications - Installation and Operating Instructions
Bulletin L-WD3
DWYER INSTRUMENTS, INC. hone: 219/879-8000 www.dwyer-inst.com
.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: [phone] e-mail: [email protected]
S ECIFICATIONS
Service: Water or conductive fluids.
Minimum Sensing Gap: 1/32˝.
Switch Type: Battery Powered odels: SPST NO SSR; External
Powered odels: DPDT relay.
Electrical Ratings:
Battery Powered odel: Pilot duty rating 250 mA @ 24 VDC;
External Powered odels: 1A @ 24 VAC/DC.
Audible Alarm: At least 85 dB @ 1 foot distance (depends on model).
Visual Alarm: Red LED for water level; Yellow LED for low battery
(battery powered models only); Green LED for power condition
(external powered models only).
Temperature Limits: 32 to 122°F (0 to 50°C).
ower Requirements:
Battery Powered odel: 3V CR2450 lithium metal battery, installed
functional,
user replaceable;
External Powered odels: 11 to 27 VAC/DC.
ower Consumption:
Battery Powered odel: 0.9 mA steady state / 3.0 mA during alarm
condition;
External Powered odels: 30 mA steady state / 85 mA during alarm
condition.
Battery Life: 5 years steady state / 48 hours during alarm condition.
Electrical Connections: 4.9´ (1.5 m), 22 AWG, PVC, UL plenum rated
cable.
Enclosure Material: ABS and polycarbonate with flammability
classification UL 94 V-0.
Enclosure Rating:
Audible Alarm odels: Water-tight up to 3/4 of the body height;
Non-Audible Alarm odels: NE A 6P (IP 68) submersible.
Weight: 4.85 oz (137.5 g).
Agency Approvals: CE, RoHS.
The Series WD3 Water Leak Detector protects equipment from water
damage by detecting the presence of water in drip pans in air handler
units, under raised floors in data centers, or on floors around sump
pumps and drains. Water is detected once it reaches a level that bridges
the two conductive strips on the bottom of the housing. Depending on the
model ordered, audible and visual alerts provide local indication of the
alarm condition and an internal switch will give remote indication or
control to prevent further build up of water.
For applications where power is not available, the odel WD3-BP-D1-A
is battery powered. Otherwise, either AC or DC supply voltages can be
used to power the water detector. The sensing height can be adjusted to
as low as 1/32˝ using the included adjustable mounting bracket. The
mounting bracket can attach to any flat surface by either using the
attached adhesive strips or mounting screws.
INSTALLATION
Mounting
The Series WD3 mounts horizontally using an adjustable mounting
bracket that allows detection from 1/32˝ up to 17/32˝. The tabs on the side
of the water detector fit into the slots on the bracket as shown in Figure
1. The mounting bracket mounts to the drip pan or flat surface by either
the attached adhesive strips or using two #6 or #8 screws.
5/16
[7.52]
4-1/8
[105.23]
1-3/16
[30.12]
2
[50.66]
5/8
[16.18]
1/8
[2.50]
5/8
[16.58]
1-5/16
[33.15]
3
[76.68]
3-5/8
[91.70]
Before attaching the mounting bracket to the desired surface,
the Series WD3 will need to be attached to the mounting
bracket. The adhesive is very strong and is not easily removed once attached.
NOTICE
Mounting
Slots
WD3 Bracket
WD3-B WD3-L
Figure 1: Mounting WD3 to Mounting Bracket

Replacing Batteries (Battery owered Model Only)
When the battery is low, a yellow warning LED will begin to flash and an
audible alarm will sound every 300 seconds to alert that it is time to
change the battery. Using a large flat head screw driver, turn the battery
cover 1/4 turn in the direction of the arrows on the cover. Remove the
battery cover by lifting it up. Remove the coin cell battery from its
compartment. Insert a new 3V CR2450 coin cell battery in the
compartment with the positive (+) side of the battery facing up. Replace
the battery cover and twist the cover using the large flat head screw driver
in the opposite direction of the arrows on the cover.
Wiring
The wires in the 4.9 ft (1.5 m) cable for the Series WD3 are color coded
to reduce wiring errors. For battery powered models, Figure 2 has the
wiring diagram. For external powered models, Figure 3 has the wiring
diagram.
Operation
After mounting and wiring the Series WD3, it is ready for operation. The
water is detected when it bridges the two conducting strips on the bottom
of the unit. Upon detecting water, the relay contact will close and a red
LED will begin to flash. On models with the built in annunciator, the
annunciator will begin to chirp until the water bridge between the
conducting strips evaporates. After water evaporates, the relay contacts
will return to their normal state.
LED Indicators
For odel WD3-LP-D2 and WD3-LP-D2-A
Green – On when power is supplied to the unit
Red – On when water is detected
For odel WD3-BP-D1-A
Yellow – On when low battery condition is detected
Red – On when water is detected
MAINTENANCE/RE AIR
Upon final installation of the Series WD3 no routine maintenance is
required. The Series WD3 is not field serviceable with the exception of
replacing the batteries on battery powered model and should be returned
if repair is needed. Field repair should not be attempted and may void
warranty.
WARRANTY/RETURN
Refer to “Terms and Conditions of Sales” in our catalog and on our
website. Contact customer service to receive a Return Goods
Authorization number before shipping the product back for repair. Be
sure to include a brief description of the problem plus any additional
application notes.
DWYER INSTRUMENTS, INC. hone: 219/879-8000 www.dwyer-inst.com
.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: [phone] e-mail: [email protected]
©Copyright 2013 Dwyer Instruments, Inc. Printed in China 7/13 FR# R3-444159-00 Rev.1
Model
WD3-B -D1-A
WD3-L -D2
WD3-L -D2-A
Output
SPST NO SSR
DPDT Relay
DPDT Relay
ower
Battery
11 to 27 VAC/DC
11 to 27 VAC/DC
Audible Alarm
Yes
No
Yes
Figure 2: Wiring for WD3-B -D1-A
Figure 3: Wiring for WD3-L -D2 and WD3-L -D2-A
YELLOW
GREEN
YELLOW
WHITE
GREEN
BLUE
BROWN
RED
BLACK
ORANGE
PWR IN