Dynabrade Dynaline 57405 User manual

Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools
(ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade’s
Warning/Safety Operating Instructions for more complete safety information.
Parts Page Reorder No. PD10•24
Effective May, 2010
Supersedes PD01•78
For Serial Number 5I3366 and Higher
Palm-Style, Air Powered, 2,400 SPM
Dynaline Sander
Note: To order replacement parts specify the model and serial number of your machine.
* Parts included in
57438 Counter
Weight Assembly.
Models:
57400 - Non-Vac
57401 - Vac-Ready
57402 - Basic Vac
57403 - Deluxe Vac
57404 - Central Vac-Ready
57405 - Versatility Kit
57407 - Non-Vac, w/clips
Adhesive: A2= Loctite #271
A8= Loctite #567
Torque: N•m x 8.85 = In. - lbs.
KEY
A
O
T
GGrease: G1= Lubriplate 630AA
Oil: O1= Air Lube
Index Key
No. Part # Description See page 2. for Machine Exhaust Assemblies.
15
17
18
19
15
22
15
7 8
14 *
13 *
10 9
6
1
4
3
2
24
25
26
28
27
42 43 44
38
35
37
39
40
41
29
30
31 32
34
33
21
20
36
157429 Felt Seal (4)
295885 Screw (2)
301211 Lock Washer (2)
4Slide Board
57433 Non-Vacuum
57432 Vacuum
557431 Transfer Pinion (2)
657427 Slider Housing Assembly (2)
(Incl. 57429 Felt Seal)
795641 Nut (2)
895642 Screw (2)
957434 Vac Adapter (Vac Only)
10 57445 Needle Bearing
11 57430 Cam Assembly
12*96027 Screw (4)
13*57439 Rail (2)
14*57438 Counter Weight
15 01139 Bearing (3)
16 95593 Set Screw
17 54467 Retaining Ring
18 54468 Ring Gear
19 54465 Planetary Carrier
20 06213 Gears (2)
21 54475 Shaft (2)
22 07146 Packing
23 57059 Lock Ring
24 95973 Washer
25 57055 Front Ring
26 57437 Front Bearing Plate
27 56047 Rotor Key
28 54470 Rotor Pinion
29 57113 Rotor/Blade Set
30 57058 Cylinder Assembly
(Incl. 95971 Line-Up Pin)
31 95971 Line-Up Pin
32 57056 Rear Bearing Plate
33 01206 Bearing
34 57054 Rear Ring
35 94590 Pin
36 57041 Comfort Platform
37 57441 Lever
38 95697 Retaining Ring
39 01025 O-Ring (2)
40 01477 Valve Stem
41 57064 Speed Regulator or
57053 Recessed Speed Reg.
42 01464 Seal
43 01472 Tip Valve
44 01468 Spring
45 01494 Inlet Bushing
57442 — Non-Vacuum
57443 — Self-Generated Vac
57444 — Central-Vac
Housing & Models Used On.
O1
O1
G1
G1
G1
G1
A2
A2
A8
A8
23 N•m T
28 N•m T
45
23
16
5
12 *
11
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Machine Exhaust Assemblies
2
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade rotary vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Connect power source to tool. Be careful not to depress throttle lever in the process.
3. Check tool speed with tachometer. If tool is operating at a higher speed than the SPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
Maintenance Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written
consent from Dynabrade, Inc.
1. All Dynabrade rotary vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if
the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 2 drops per minute).
Dynabrade Air Lube (P/N 95842: 1 pt. 473 ml.) is recommended.
2. Mineral spirits are recommended when cleaning tool. Do not clean tool with any solvents or oils containing concentrated acids, esters, ketones
chlorinated hydrocarbons or nitro hydrocarbons.
3. An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 10681 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of
pneumatic components. Operates 55 SCFM @ 100 PSIG has 1/2" NPT female ports.
4. Frequent drainage of water traps in air lines is recommended.
5. Some silencers on air tools may clog with use. Clean and replace as required.
6. A Motor Tune-Up Kit (P/N 96107) is available which includes assorted parts to help maintain and repair motor.
Safety Instructions:
• Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or
death. Follow safety procedures posted in workplace.
• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
• Tool SPM must never exceed abrasive/sanding pad SPM rating, regardless of tool capacity.
• Operate machine for 30 seconds before application to workpiece to determine if machine is safely performing before work begins.
• Always disconnect power supply before changing abrasive or making machine adjustments.
• Inspect abrasives and sanding pads for damage or defects prior to and during operation of tool.
• Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
• Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Central Vacuum/Machine Exhaust
Non-Vacuum/Machine Exhaust Self Generated Vacuum (Vac-Ready) / Machine Exhaust
6721
11
21 3 4
2 1 3 4
5
8910
Index Key
No. Part # Description
157065 Cone Plug
257066 Muffler Cap
356027 Muffler Insert (2)
456028 Muffler Cap
557124 Muffler Assembly
657083 Vacuum Adapter
796197 Dowel Pin
895526 O-Ring
959088 Vac Nozzle
10 57067 Vac Tube
11 57093 Vacuum Adapter
Lifetime Warranty
All Dynabrade portable pneumatic power tools are rigorously inspected and performance tested in our factory before shipping to our customers. If a Dynabrade tool develops
a performance problem and an inherent defect is found during normal use and service, Dynabrade will warrant this tool against defects in workmanship and materials for
the lifetime of the tool. Upon examination and review at our factory, Dynabrade shall confirm that the tool qualifies for warranty status, and will repair or replace the tool at
no charge to the customer. Normally wearable parts and products are NOT covered under this warranty. Uncovered items include bearings, contact wheels, rotor blades,
regulators, valve stems, levers, shrouds, guards, O-rings, seals, gaskets and other wearable parts. Dynabrade’s warranty policy is contingent upon proper use of our tools
in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment that has been subjected to misuse, negligence, accident or
tampering in any way so as to affect its normal performance. To activate lifetime warranty, customer must register each tool at www.dynabrade.com. Dynabrade will not
honor lifetime warranty on unregistered tools. A one-year warranty will be honored on all unregistered portable pneumatic power tools. Lifetime warranty applies only to
portable pneumatic tools manufactured by Dynabrade, Inc. in the USA. Lifetime warranty applies only to the original tool owner; warranty is non-transferable.
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Disassembly/Assembly Instructions – Dynaline Sander
Important: Manufacturers warranty is void if tool is disassembled before warranty expires.
A complete Tune-Up Kit, (P/N 96107), is available which includes assorted parts to maintain and repair motor. A Motor Repair Kit (P/N 96046) is
available which contains special tools for disassembly/assembly of machine.
Gearbox Disassembly:
1. Disconnect tool from power source.
2. Invert machine and secure in vice, using 57092 Collar (Supplied in 96046 Repair Kit) or padded jaw.
3. Disconnect sanding pad by removing 95885 Screws (2) with a 3mm Hex Key.
4. Remove gearbox assembly by removing 95642 Screws (2) and 95641 Hex Nuts with a phillips head screw driver.
5. Carefully separate 57427 Slider Housing halves. Remove one gearbox half, making sure no parts fall to the ground.
6. Remove and set aside the 57433 Slide-Board on non-vacuum models (57432 on vacuum models), 57431 Transfer Pinion (2), 57438 Counterweight
Assembly, 57445 Needle Bearing and the other 57427 Slider Housing half.
7. Clean grease off old dirty components and inspect for damaged parts.
Motor Disassembly:
1. Insert 56058 Lock Ring Wrench (Supplied in 96046 Repair Kit) into corresponding tabs of lock ring and unscrew. Pull with a side to side action to
remove motor from housing. Remove 57054 Rear Ring, 57055 Front Ring, 95973 Washer, and 57059 Lock Ring. Motor may now be serviced.
2. Remove 54467 Retaining Ring/Planetary Gear Assembly using (2) 50679 26mm wrenches (Supplied in 96046 Repair Kit). Set aside.
Note: See planetary gear disassembly.
3. Remove 57056 Rear Plate By holding 57058 Cylinder with a 2" Bearing Separator and pressing 54470 Rotor Pinion out of 01206 Bearing.
4. Remove 57113 Blade (5), rotor set and 56047 Rotor Key.
5. Disassemble 57437 Front Plate by pressing 54470 Rotor Pinion through front plate. Note: One 01139 Bearing will remain on rotor pinion. To remove
press pinion through remaining bearing.
6. Press 01206 Rear Bearing from 57056 Bearing Plate.
Planetary Gear Disassembly:
1. Insert 54470 Rotor Pinion into the center of the planetary gear assembly. Install the 56047 Rotor Key into
the key way of the rotor pinion, and hold the rotor pinion in a soft jaws vise.
2. Place a 26mm wrench on the flats of the 54467 Retaining Ring and an adjustable 3mm pin spanner
wrench into the two empty holes on the 57430 Cam Assembly. Turn counterclockwise to loosen and remove
the cam assembly.
3. Remove 95593 Set Screw from Retaining Ring/Planetary Gear Assembly using a 5/64" allen wrench.
4. Remove 54465 Planetary Carrier by pressing out from 01139 Bearing. 02613 Gears (2) and 54475 Shafts
(2) can now be removed from planetary carrier.
5. Remove 54468 Ring Gear by tapping retaining ring on a hard surface. Once the ring slides towards the
front, it will be necessary to use your fingers to remove it the rest of the way.
Note: If hard to remove, heat may be applied to retaining ring and pliers used to remove gear.
6. Press 01139 Bearing from 54467 Retaining Ring.
Motor Disassembly Complete.
Planetary Gear Assembly:
Important: Be certain all parts are cleaned, properly greased and in good repair before assembling.
1. Press 01139 Bearing into 54467 Retaining Ring.
2. Place 54468 Ring Gear into 54467 Retaining Ring lining up one of the notches with set screw hole.
3. Hand tighten 95593 Set Screw in place using 5/64" hex key.
4. Install lightly greased Planetary Carrier. Place 54475 Shafts into gears.
5. Slide entire Planetary Carrier Assembly into 54467 Retaining Ring (1/4"-28 female thread facing down).
6. Insert 54470 Rotor Pinion into the center of the planetary gear assembly. Install 56047 Rotor Key into the
key way of the rotor pinion.
7. Apply 1 drop of #271 Loctite®(or equivalent) to the threads of 57430 Cam Assembly.
8. Place a 26mm wrench on the flats of the 54467 Retaining Ring and an adjustable 3mm pin spanner wrench
into the two empty holes on the 57430 Cam Assembly. Turn clockwise to install the cam assembly.
Motor Assembly:
1. Press 01139 Bearing onto Rotor Pinion until seated against shoulder as shown in Drawing 1.
2. Press assembly into 57437 Front Bearing Plate as shown in Drawing 2 and check for smooth rotation.
3. Place 07146 Packing in front plate bore and press 01139 Bearing into bore onto packing as shown in Drawing 3.
4. Invert rotor pinion in support. Install 56047 Rotor Key and 57113 Blade and Rotor Set onto rotor pinion.
Note: Blades should be lightly lubricated with Dynabrade Air Lube P/N 95842 (or equivalent) before installation.
5. Place 57058 Cylinder Assembly over rotor. The “short” line-up pin goes toward the front plate.
6. Place 57056 Rear Plate (with 01206 Bearing pressed into place) over shaft and “long” end of line-up pin.
Press fit in place as shown in Drawing 4.
Drawing #1
Bearing press tool
(Press on inner race)
01139 Bearing
Support
54470
Rotor Pinion
Drawing #2
Bearing press tool
(Press on inner race)
57437 Front Plate
Support
54470
Rotor Pinion
Drawing #3
Drawing #4
Bearing press tool
(Press on inner race)
57437 Front Plate
01139 Bearing (2)
07146 Packing
Support
54470
Rotor Pinion
Bearing press tool
(Press on inner race)
57056 Rear Plate &
01206 Rear Bearing
57437 Front Plate
95971 Line-Up Pin
57058 Cylinder
Assembly
Support
(continued on next page)
3
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

96107 Motor Tune-Up Kit:
• Includes assorted parts to help maintain
and repair motor.
Grease and Grease Gun
• Multi-purpose grease for all types of bearing, cams, gears.
• High film strength; excellent resistance to water, steam, etc.
• Workable range 0°F to 300°F.
95541: Push-type grease gun.
95542: 10oz. (283.5g) tube.
Optional Accessories
Disassembly/Assembly Instructions – Dynaline Sander (continued)
7. Place 57054 Rear Ring over the rear plate and line-up pin. Turn the motor over and place 57055 Front Ring over the front plate making sure the “legs
and fingers” on the front and rear rings line-up.
Note: The small cut-outs on both rings should line-up with the square holes in the cylinder/end plate assembly.
8. Place 95973 Washer and 57059 Lock Ring onto the front ring with one drop of pneumatic tool oil spread between the washer and the lock ring.
9. Secure motor housing in vice, using 57092 Collar or padded jaws. Spread 2-3 drops of pneumatic tool oil around the housing bore for ease of insertion
of motor assembly. Slide motor assembly into secured housing.
Note: Be certain line-up pin enters the pocket in the bottom of the housing and the “legs” of the rings stay in-line.
10. Tighten lock ring with 56058 Lock Ring Tool to 28 N•m/250 in. - lbs.
Gearbox Assembly:
1. Place 57428 Sliders in gearbox halves.
2. Install 57429 Felt Seals into gear housing halves. Using Dynabrade’s 95542 Gear Grease (or equivalent), grease entire slider including, transfer pinion
holes and groves.
3. Grease slide board gear pack and bearing pocket. Grease 57445 Bearing. Place bearing on 57430 Cam Assembly. Grease counterweight gear packs.
4. Place counterweight over 57430 Cam Assembly with tool inverted and exhaust at six o'clock. Place cam assembly bearing at three o'clock. Take one
gear box halve and slide it onto the housing groves.
5. Place transfer pinion on counter weight gear rack, sliding pinion shaft partially into mated hole on slider. Repeat for second shaft.
Important: Make sure counter weight is positioned dead center of cam assembly when transfer pinions are installed. This ensures correct timing.
6. Making sure needle bearing is still located at three o'clock, place slide board railing into groove on slider while aligning needle bearing into bearing
channel on slider board.
7. Place other gearbox half onto grooves of motor housing, making sure all parts align. Press both gear box halves together.
8. Install 95842 Screws and 95841 Nuts and tighten. Install Pad.
Valve And Speed Regulator Disassembly/Assembly:
1. Secure housing in vice using 57092 Collar or padded jaw.
2. Remove inlet bushing, 01468 Spring, 01472 Tip Valve, and 01464 Seal from housing.
3. Remove 95697 Snap Ring. Press the 57064 Speed Regulator and 01447 Valve Stem out of the housing. Remove the 01025 O-Rings (2).
4. Place new 01025 O-Rings (2) on the speed regulator and place in housing with valve stem. Install new 95967 Snap Ring.
5. Place 01464 Seal in housing so the pocket of seal sets horizontal and towards the top of the tool. Using a pair of tweezers or needle nose pliers, place
the tip valve in the housing so that its pin goes into the valve stem hole and the hinge seats into the pocket of the seal. Place 01468 Spring into the
housing small end first.
6. Spread one drop of # 271 Loctite®(or equivalent) around the first threads of the inlet bushing and tighten into housing to 23 N•m/200 in. - lbs.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet
with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite®is a registered trademark of Loctite Corp.
Notice:
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
Note: To order replacement parts specify the model and serial number of your machine.
DYNABRADE
®
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: [phone] • Fax: [phone] • International Fax: [phone]
DYNABRADE EUROPE S.àr.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: [phone] • Fax: [phone]
©DYNABRADE, INC., 2010 PRINTED IN USA PD10.24_05/10
Visit Our Web Site: www.dynabrade.com Email: Customer[email protected]
Model Motor Motor Sound Maximum Air Flow Air Pressure Weight Length Height
Number hp (W) RPM Level SCFM (LPM) PSIG (Bars) Pound (kg) Inch (mm) Inch (mm)
All Models .3 (186) N/A 84-85 dB(A) 18 (510) 90 (6.2) 2.6 (1.2) 7 (178) 3-3/4 (95)
Additional Specifications: Air Inlet Thread 1/4" NPT • Hose Size 1/4" or 6mm
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade