DynaColor NH720 Series User manual

00P6NH720ZXSEA3
Full HD Speed Dome IP Camera
Installation Guide
Indoor / Outdoor
Version 1.3

Installation Guide
1
Preface
The information given in this manual was current when published. The company reserves
the right to revise and improve its products. All specifications are subject to change without
notice.
Notice
This manual provides the installation information for the indoor integrated high
speed dome. To work with the Dome Cameras, any installer or technician must
have the following minimum qualifications:
 A basic knowledge of CCTV systems and components
 A basic knowledge of electrical wiring and low-voltage electrical hookups
 A basic knowledge of network system setting
 Have read this manual completely
Copyright
Under copyright laws, the contents of this user manual may not be copied,
photocopied, translated, reproduced or reduced to any electronic medium or
machine-readable format, in whole or in part, without prior written permission of
the company
Important Information
Before proceeding, please read and observe all instructions and warnings in
this manual. Retain this manual with the original bill of sale for future reference
and, if necessary, warranty service. When unpacking the unit, check for missing
or damaged items. If any item is missing, or if damage is evident, DO NOT
INSTALL OR OPERATE THIS PRODUCT. Contact the dealer for assistance.
Regulation
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.

Installation Guide
2
This symbol on the product or on its packaging indicates
that this product shall not be treated as household waste in
accordance with Directive 2002 / 96 / EC. Instead it shall be
handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By proper
waste handling of this product, please ensure that it has no
negative consequences for the environment and human
health, which could otherwise be caused if this product is
thrown into the garbage bin. The recycling of materials will
help to conserve natural resources.
For more details information about recycling of this product,
please contact the local city office, household waste
disposal service or the shop where purchased the product.
Compliance is evidenced by written declaration from our
suppliers, assuring that any potential trace contamination
levels of restricted substances are below the maximum level
set by EU Directive 2002 / 95 / EC, or are exempted due to
their application.

Installation Guide
3
Warnings and Cautions
 Handle the camera carefully
Do not abuse the camera. Avoid striking, shaking, etc. The camera
could be damaged by improper handing or storage.
 Installing electricity wiring carefully
Ask qualified personnel of electrical wiring for the installation. Please
note that input electricity to the unit is at tolerance of DC 12V / AC 24V ±
10%.
The camera is capable of surge protection; ensure AC power model unit
grounded appropriately against damage of heavy current or electric
shock.
 Do not disassemble the camera
To prevent electric shock, do not remove screws or covers. There are no
user serviceable parts inside. Ask a qualified service person for
servicing.
 Do not block cooling holes on the bracket
This camera has a cooling fan inside. Blocking the cooling holes leads to
build up of heat the camera and may cause malfunction.
 Do not operate the camera beyond the specified temperature,
humidity or power source ratings
Use the camera under conditions where temperature is between 0°C ~
40°C (32°F ~ 104°F), and relative humidity is below 90%.
 Do not expose the camera to rain or moisture, or try to operated it
in wet areas
This product is designed for indoor use or locations where it is protected
from rain and moisture. Turn the power off immediately if the camera is
wet and ask a qualified service person for servicing. Moisture can
damage the camera and also create the danger of electric shock.
 Do not use strong or abrasive detergents when cleaning the
camera body
Use a dry cloth to clean the camera when it is dirty. In case the dirt is
hard to remove, use a mild detergent and wipe the camera gently.

Installation Guide
4
 Never face the camera towards the sun
Do not aim the camera at bright objects. Whether the camera is in use or
not, never aim it at the sun or other extremely bright objects. Otherwise,
the camera may be smeared or damaged.

Installation Guide
5
Table of Contents
1. Introduction ........................................................................................................................... 6
2. Standard Package Contents ................................................................................................. 6
3. Camera Cable Connections .................................................................................................. 8
3.1 Switch / Connector Definition ....................................................................................... 8
3.2 Cable Requirements .................................................................................................... 9
3.2.1 Power Connection ........................................................................................ 9
3.2.2 Ethernet Cable Connection .......................................................................... 9
4. Dome Camera Installation .................................................................................................. 10
4.1 Camera Dimensions .................................................................................................. 10
4.2 Optional Accessories ................................................................................................. 11
4.3 Ceiling Mount ............................................................................................................. 21
4.3.1 Hard Ceiling Mounting ................................................................................ 21
4.3.2 In-Ceiling (T-Bar) Mounting ........................................................................ 24
4.3.3 Ceiling Mounting with Indoor Mounting Kit .................................................. 28
4.3.4 Ceiling Mounting with Straight Tube ........................................................... 30
4.4 Wall Mount................................................................................................................. 32
4.4.1 Swan Tube ................................................................................................. 32
4.4.2 Compact Pendent Mount ............................................................................ 34
4.4.3 Standard Pendent Mount............................................................................ 36
4.4.4 Wall Box Mounting ..................................................................................... 38
4.5 Corner Mount ............................................................................................................. 40
4.5.1 Corner Standard Mounting Plate / Corner Plate Mini .................................. 40
4.5.2 Corner Thin / Wide Box Mounting ............................................................... 42
4.6 Pole Mount ................................................................................................................ 44
4.6.1 Pole Thin / Wide Direct Mounting ............................................................... 44
4.6.2 Pole Thin / Wide Box Mounting .................................................................. 46

Installation Guide
6
1. Introduction
The Full HD Speed Dome IP Camera is designed to deliver superb performance
and durability with an intelligent and stylish housing that is suitable in any
security and surveillance installation.
2. Standard Package Contents
Before proceeding, please check the box contains the items listed here. If any
item is missing or has defects, DO NOT install or operate the product and
contact dealer for assistance.
Indoor Model
Camera Body Optical Cover
Hard Ceiling Mount
M4 Screw (x4)
Plastic Anchors (x4)
Quick Guide CD: Operation Manuals

Installation Guide
7
Outdoor Model
Camera Body with
Outdoor Mount Kit
M3 Standard Screw (x1)
M3 Security Screw (x1)*
M5 Standard Screw (x1)
M5 Security Screw (x1)*
Waterproof Rubber
Quick Guide
CD: Operation Manuals
Optical Cover Lubricant Security Torx*
*Optional: For Vandal Proof Cover only.

Installation Guide
8
3. Camera Cable Connections
Before installing or connecting the Dome Camera, please refer to this section
and complete preparations for dome setups and various switch settings.
There will be a PE cloth sheet covered inside the dome cover and a lens cap on
the lens for shipping protection. Follow the steps below to remove those
protective materials.
Step 1: Unpack the dome package and take out the dome body.
Step 2: Rotate and remove the protective cover.
Step 3: Remove the PE cloth sheet and take off the lens cap.
Step 4: Attach the dome cover to the dome body.
3.1 Switch / Connector Definition
There are various connectors located on the Dome Camera’s back plate as
shown in the figures below. Please refer to the diagrams and tables
accompanied with for use of each switch / connector.
Indoor Outdoor
A RJ-45 Connector
B ALARM I/O
C Power
D Micro SD Card Slot
E Factory Reset Button
F Audio I/O
NOTE: DO NOT change the network Speed Dome Camera’s
Communication Switch factory default settings.

Installation Guide
9
3.2 Cable Requirements
For operation, the network Speed Dome IP Camera requires power cable and
RJ-45 as described below:
3.2.1 Power Connection
Please refer to the illustrations below to connect power core through the
supplied power adaptor.
3.2.2 Ethernet Cable Connection
Use of Category 5 Ethernet cable is recommended for network connection; to
have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the network
Speed Dome Camera, and the other end of the cable to the network switch or
PC.
NOTE: In some cases, users may need an Ethernet crossover cable
when connecting the network Speed Dome Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs are
unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Pin
Definition
1 AC 24-
2 FG
3 AC 24+

Installation Guide
10
4. Dome Camera Installation
Basing on user’s installation environments, the Dome Camera can be installed
on ceiling, on wall or on pole. In the following sections, various Dome Camera
installation accessories, installation methods and installation procedures will be
described in detail. In addition, the next section will provide the Dome Camera’s
dimensions for reference before installation.
4.1 Camera Dimensions
The Dome Camera’s dimensions are as below show detailed dimensions for the
Dome Camera’s different parts.
Indoor
Outdoor

Installation Guide
11
4.2 Optional Accessories
Dome Camera Accessories
Transparent / Vandal Proof
Transparent Cover (Standard)
Vandal Proof Cover (Optional)
Power Adapter
77H07-A1015 (Input: 100~115 VAC / Output: 24 VAC 36 VA)
77H07-A2015 (Input: 220~230 VAC / Output: 24 VAC 36 VA)
NOTE: When wiring, make sure the G / Y wire (Ground) inserted into
the mid-pin of the terminal block.

Installation Guide
12
Mounting Accessories
Hard Ceiling Mount (Standard Equipment)
For Hard Ceiling Installation. Height: 24.01 mm (0.95 inches);
Diameter of the three holes: 4.2 mm (0.17 inches);
Diameter of the bracket: 103.1 mm (4.1 inches); Weight: 65 g (0.14 Ibs)
In-Ceiling (T-Bar) Mount
For In-Ceiling Installation. Height: 166 mm (6.5 inches); Diameter: 276 mm (10.9 inches);
Weight: 1.1 kg (2.4 lbs)

Installation Guide
13
Indoor Mounting Kit (IMK)
Height (with Hard Ceiling Mount): 75.1 mm (3.0 inches); Height: 58 mm (2.3 inches);
Total Width: 110.66 mm (4.4 inches); Weight: 260 g (0.56 Ibs)
Standard Pendent Mount
White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs);
Diameter: 45 mm (1.8 inches).
Supplied with M8x12 screw x1, spring washer-8 x1, pendent tube washer x1,
rubber washer-8 x1 and sponge x2.

Installation Guide
14
Compact Pendent Mount
184×104×115.2 mm (7.24×4.09×4.54 inches); 0.6kg (1.2 lbs).
Supplied with rubber washer-8 x1, pendent tube washer x1, spring washer-8 x1 and
M8x12 screw x1.
Straight Tube
Iron; Height: 250 / 500 mm (9.8 / 19.7 inches);
Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs).
Supplied with M8x12 screw x1, spring washer-8 x1, pendent tube washer x1,
rubber washer-8 x1 and waterproof rubber x1.

Installation Guide
15
Swan Tube
For mounting with Swan Tube.
White; Iron, Dimension: 835 x 300 mm (32.9×11.8 inches); Diameter: 45 mm (1.8 inches);
Weight: 3.8 kg (8.4 lbs).
Supplied with pendent tube washer x1, rubber washer-8 x1, waterproof rubber x1,
spring washer-8 x1 and M8x12 screw x1.
Corner Plate Mini
For mounting with Compact Pendent Mount.
270(L) x 166(W) x 95(D) mm (8.7×8×4.6 inches).
Supplied with washer-8 x4, spring washer-8 x4, M8x16 screw x4 and M8 nut x4.

Installation Guide
16
Corner Standard Mounting Plate
222(L) x 204(W) x 117(D) mm (8.7 x 8 x 4.6 inches); 2 kg (4.4 lbs).
Supplied with washer-8 x4, spring washer-8 x4, M8x16 screw x4, and M8 nut x4.
Pole Thin Direct Mounting
232(L) x 136(W) x 60(D) mm (9.1 x 5.4 x 2.4 inches); Diameter: 112~130 mm (4.4~5 inches);
Weight: 0.7 kg (1.6 lbs).
Supplied with stainless steel straps x4, Mx16 screw x4, washer x4 and spring washer-8 x4.

Installation Guide
17
Pole Wide Direct Mounting
270(L) x 170(W) x 60(D) mm (10.6 x 6.7 x 2.4 inches);
Diameter: 112~140 mm (4.4~5.5 inches); Weight: 1 kg (2.2 lbs).
Supplied with M8x16 screw x4, washer x4, stainless steel straps x4 and spring washer-8 x4.
Corner Thin Box Mounting
300(L) x 164(W) x 222(D) mm (11.8 x 6.5 x 8.7 inches); Weight: 3 kg (6.7 lbs).
Supplied with M8x16 screw x4, washer-8 x4, and spring washer-8 x4.

Installation Guide
18
Corner Wide Box Mounting
232(L) x 234(W) x 210(D) mm (9.1 x 9.2 x 8.3 inches); Weight: 2.7 kg (6 lbs).
Supplied with M8x16 screw x4, washer-8 x4, and spring washer-8 x4.
Pole Thin Box Mounting
291(L)×136(W)×242 (D) mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs).
Supplied with M8x16 screw x4, washer-8 x4, spring washer x4 and stainless steel straps x4.

Installation Guide
19
Pole Wide Box Mounting
270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs).
Supplied with M8x16 screw x4, washer-8 x4, spring washer-8 x4 and stainless steel
straps x4.
Wall Box Mounting
270(L) x 166(W) x 95(D) (10.6 x 6.5 x 3.7 inches); Weight: 2.2 kg (4.84 lbs).
Supplied with M8x16 screw x4, washer-8 x4 and spring washer-8 x4.