E-z-rect Trim-line User manual

TRIM-LINE Boltless Shelving

Assembly Instructions

Place post flat on the ground so that Post Connector

slots are on the inside and the seam is on the outside.

Post Connectors are adjustable as illustrated on the

back page of the assembly instructions and are

required for end frame assembly.

Starting from the bottom tap in one side of the Post

Connector and LOCK IMMEDIATELY. Then tap in and

lock the other side. The post will have to be spread

lightly as you work your way up the post. Use a 1/4" or

a 3/8" screwdriver or chainsaw wrench to lock

connectors. Assembly time is approximately 1 to 2

minutes per 84" (2134mm) frame.

Load

Capacities

Maximum Evenly Distributed Static Load

Per Pair of Connectors

36"

0.91m

39 1/2

1.00m

48"

1.22m

60"

1.52m

66"

1.68m

72"

1.83m

4 Shelf Clips

& one Metal

20ga. Shelf

350 lb

159 kg

290 lb

132 kg

200 lb

91 kg

- -

TFC

390 lb

177 kg

350 lb

159 kg

290 lb

132 kg

191 lb

87 kg

- -

TBC

600 lb

272 kg

550

249 kg

500 lb

227 kg

- -

TWB

700 lb

318 kg

675 lb

306 kg

650 lb

295 kg

550 lb

249 kg

450 lb

204 kg

375 lb

170 kg

TWB with one

Combination

Tie Bar

975 lb

442 kg

950 lb

431 kg

925 lb

420 kg

900 lb

408 kg

800 lb

363 kg

700 lb

318 kg

Please note load capacities & components subject to change without notice.

SAFE WORKING LOADS OF UP TO 7,000 LBS (3,175 kgs) PER PAIR

OF POSTS OR BAY OF SHELVING.

SAFETY FACTOR OF 1.66 TO 1.00 BASED ON MINIMUM YIELD

STATIC LOADING ONLY.

PLEASE CONTACT THE FACTORY FOR CAPACITIES NOT SHOWN

IN CHART.

RECT MANUFACTURING LTD.

Head Office: North Vancouver, P: 604 929 5461 Eastern Sales: Mississauga, P: 905 564 0890 UK Sales: Oxon, P: 01993 779494

Email: sales@ezrect.ca Web: www.ezrect.ca Email: torontosales@ezrect.ca Web: www.ezrect.ca Email: mail@ezrshelving.com Web:

www.ezrshelving.com

E-Z-Rect Manufacturing Ltd. TL Revised October 2019

POST

CONNECTORS

Use to join posts (refer to chart for quantity).

Available depths: 12" (0.30m), 15" (0.38m),

18" (0.46m), 24" (0.61m),

30" (0.76m), 36" (0.91m).

COMBINATION TIE BARS

Use with TWB connectors.

Available depths: 18" (0.46m), 24" (0.61m),

30" (0.76m), 36" (0.91m).

Allow TCTB hook to snap into connector

slot with its own spring.

TFCV FRAME CONNECTOR

Use with particleboard shelves.

Available lengths: 36" (0.91m),

39 1/2" (1.00m), 48" (1.22m).

ONLY FOUR BASIC COMPONENTS

1. Post 3. Frame Connector.

2. Post Connector 4. Shelf (metal or particle board)

TRB GARMENT ROD SUPPORT

Use to support 1" O.D. galvanized garment hang rod.

Available depths: 12" (0.30m), 15" (0.38m),

18" (0.46m), 24" (0.61m),

30" (0.76m), 36" (0.91m).

FRAME

CONNECTOR

SHELF

PLASTIC CAP

POST

CONNECTOR

HEIGHT

3' TO 20'

WIDTH

2' TO 6'

DEPTH

1' TO 3'

F R A M E A S S E M B L Y

S T E P O N E S T E P T W O

POST

CONNECTOR

LOCK

FIRST

LOCK

THIRD

LOCK

FIFTH

LOCK

SIXTH

LOCK

FOURTH

LOCK

SECOND

SAFETY

TWIST LOCK

SCREWDRIVER OR

CHAINSAW WRENCH

CAUTION

– P O S T C O N N E C T O R M U ST B E L O C K E D F O R S A F E T Y

POST

ACK PLASTIC CAP

ACK PLASTIC

FLOOR PROTECTOR

SHELF CLIPS

4 Required per shelf level

(2 Right Hand & 2 Left Hand)

Used for metal shelves.

CONNECTOR LOCKING CLIP

Simply snap in connector

locking clip where/when

required to lock connector.

TFCL FRAME CONNECTOR

Use with metal shelves.

Available lengths: 36" (0.91m),

39 1/2" (1.00m), 48" (1.22m).

TBC FRAME CONNECTOR

Use with metal or particleboard shelves.

Available lengths: 36" (0.91m),

39 1/2" (1.00m), 48" (1.22m).

TWB FRAME CONNECTOR

Use with metal or particleboard shelves

and as a kickplate.

Available lengths: 36" (0.91m),

39 1/2" (1.00m), 48" (1.22m),

60" (1.52m), 66" (1.68m), 72" (1.83m).

BLACK PLASTIC

ZINC PLATED

STACKABLE SHIM FLOOR PROTECTOR SHIM

WARNING:

PLEASE FOLLOW ASSEMBLY INSTRUCTIONS. DO NOT USE SHELVES OR CONNECTORS WITH COMPONENTS OTHER THAN E-Z-RECT PRODUCTS.

NOT LOCKED

LOCKED

TAB FULLY LOCKED

SH EL F P L AC EM ENT

–

L A Y T HE S HE L F O N T O P O F F R A M E C O N N E C T O R

ON TOP

PLACED

CORRECT

INCORRECT

TRIM-LINE Boltless Shelving

Assembly Instructions

ALLOWABLE SPACING BETWEEN FRAME CONNECTORS

NUMBERS OF POST CONNECTORS REQUIRED

Light to Medium Loads

up to 3,000lb (1,361kg)

or up to 24" (610mm) in Depth

Height of Post Light to Medium Loads

up to 3,000lb (1,361kg) or

up to 24" (610mm) in Depth

Inches Metric

Two Hook Three Hook 24" to 36"

48" to 84"

96" to 108"

120" to 144"

610mm to 914mm

1219mm to 2134mm

2438mm to 2743mm

3048mm to 3658mm

Dimension A

Not to Exceed 12" (305mm) 20" (508mm)

Dimension B

Not to Exceed 36" (914mm) 48" (1219mm)

Two Hook Connectors

ALLOWABLE SPACING BETWEEN FRAME CONNECTORS

NUMBERS OF POST CONNECTORS REQUIRED

Heavy Loads over 3,000lb (1,361kg)

to 7,000lb (3,175kg) or 30" (762mm)

and 36" (914mm) in Depth

Height of Post Heavy Loads over 3,000lb (1,361kg)

to 7,000lb (3,175kg) or 30" (762mm)

and 36" (914mm) in Depth

Inches Metric

Two Hook

Three Hook

24" to 36"

48" to 84"

96" to 108"

120" to 144"

610mm to 914mm

1219mm to 2134mm

2438mm to 2743mm

3048mm to 3658mm

Dimension A

Not to Exceed

Bottom

6" (152mm)

Dimension B

Not to Exceed

24" (610mm)

30" (762mm)

IMPORTANT NOTES:

•Post Connector requirements are for static loading only; no shocks, vibrations, seismic, mobile or other special conditions are considered.

•Always lock all post connectors on both sides to the posts that make up the shelving end frame. Refer to the assembly instructions guide for typical placement.

•Be sure the post connectors are tapped down completely so the locking tab can be engaged before twisting and locking tab as per drawing. It is best to use a chainsaw wrench

but a 3/8" screwdriver can also be used.