EAE MD100 User manual

!
!
!
EAE#KNX#Motion#Detector##!
Product#Manual#MD100#!
#!
#!
!
!!
!!
!!
!!
!
!"#$"%&'()$"*%+,-.,%!
!!
%!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!1!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
Content&!
1!!General!...............................................................................................................................................!2!
1.1!!Technical!Data!.............................................................................................................................!2!
1.2!!Operation!and!Display!.................................................................................................................!4!
1.3!!Scale!Drawings!............................................................................................................................!5!
2!!Communication!Object!Information!..................................................................................................!6!
2.3!!Communication!Object!Table!......................................................................................................!6!
2.4!!Communication!Object!Description!............................................................................................!8!
3!!Parameters!.......................................................................................................................................!12!
3.3!!General!......................................................................................................................................!12!
3.4!!Presence!....................................................................................................................................!14!
3.5!!Brightness!.................................................................................................................................!16!
3.6!!Constant!light!level!...................................................................................................................!17!
3.7!!Lighting!......................................................................................................................................!19!
3.8!!HVAC!.........................................................................................................................................!20!
!
!!
!! !! !

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!2!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
1 General&&
§ MD100!KNX!Motion!Detector!is!ideal!for!interior!rooms!such!as!medium!to!large-size!offices,!
corridors,!classrooms,!conference!and!meeting!rooms,!parking!buildings,!warehouses!and!
sport!halls.!Detector!is!available!in!two!models;!flush!mounted!and!surface!mounted.!Both!
models!can!detect!the!motion!over!9m!diameter!at!installation!height!of!2.5m.!!
!!
§ Constant!light!function!can!be!applied!in!dependence!of!presence!information!thanks!to!
integrated!brightness!sensor!and!movement!sensor.!MD!100!regulates!the!ambient!
brightness!to!a!defined!brightness!value.!!
!!
§ Lighting!can!be!set!to!different!brightness!levels!with!corridor!function!based!on!occasions!
such!as!"motion!detection,!after!movement,!no!action".!Stay-on!time!can!be!changed!the!by!
end!user.!!
!!
§ Air-conditioning!and!ventilation!systems!can!be!controlled!by!independent!HVAC!channel.!!
§ Presence!information!can!be!sent!to!presence!monitoring!applications!by!independent!
presence!channel.!!
!!
§ The!EAE!KNX!Presence!Detector!MD!100!can!either!used!as!a!standalone!device!or!
masterslave!device!(parallel!operation!with!other!MD!100s)!according!to!necessity!of!project.!!
!!
§ MD!100!enables!fully-automatic!and!semi-automatic!lighting!control.!!
!!
§ Test!and!calibration!mode!allows!for!easy!installation.!!
!!
§ The!device!does!not!require!an!additional!power!supply.!!
!!
%!
%!
&!/0*%1$234$%56478"9%#$56':7%;<9=346:%6##"$==%3=%>.?@.?@A??B@%!
%% %!
1.1 Technical&Data&&
/9;$%85%;"87$4738C%!
IP!20!!
EN!60!529!!
D65$79%4:6==%!
II!!
EN!61!140!!
E8F$"%=';;:9%*%!
Voltage!!
21V…!30V!DC,!KNX!line!!
%!
Current!consumption!!
<!10!mA!!
G;;:346738C%G"$6%!
!!
Interior!rooms!!
D$C=8"%/9;$%!
!!
Passive!infrared!!
HC=76::6738C%!
Location!!
Ceiling!!
%!
Recommended!height!!
2,5m!-!5m!!
1$7$4738C%!
Diameter!(at!height!of!2,5m)!!
9m!movement!detection!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!3!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
%!
Area!!
64!m2!!
%!
Angle!!
360°!!
%!
Light!level!!
10!–!1000!lux!!
G##3738C6:%4<6CC$:=%!
!!
Brightness,!presence!channel,!HVAC!
channel!!
E6"6::$:%8;$"6738C%!
!!
Master/Master,!Slave/Master!!
!;$"673CI%$:$($C7=%!
LED!(red)!and!button!!
For!physical!address!!
/$(;$"67'"$%"6CI$%!
Ambient!!
-5°!C!!!+!45°!C!!
%!
Storage!!
-25°!C!!!+!55°!C!!
%!
Transport!!
-25°!C!!!+!70°!C!!
13($C=38C=%!
!!
42.5!x!42,5!x!12!mm!!
J$3I<7%!
0.06!kg!!
!!
K8L%!
Plastic,!polycarbonate,!colour!white!!
!!
M0%!
In!accordance!with!the!EMC!
guideline!and!low!voltage!!
!!
G;;:346738C%;"8I"6(%!
Communications!objects!!
Number!of!addresses(max)!!
%!
44!!
255!!
%!
%!
&!/0*%Device!default!physical!address!is!15.15.255.!In!order!to!configure!KNX!Motion!detector,!ETS!
application!file!“.knxprod”!is!needed.!It’s!possible!to!download!the!file!on!EAE!website.!ETS!is!
required!for!programming!the!device.!Parameter!settings!and!related!group!addresses!can!be!
changed!by!ETS.!Learn!more!by!reading!ETS!help!file.%!
%!
%!
%!
%!
%!
%!
%!
%!
%!
1$7$4738C%N6CI$%%
Detection!range!depends!on!movement!types!so!that!these!types!are!divided!as!follows;!!
a) Sitting!position!in!working!desk!height!(0,8m)!!
b) Walking!straight!to!the!detector!!!
c) Walking!across!the!detector!!
d) Area!of!the!brightness!measuring!in!working!desk!height!(0,8m)!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!4!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
Table!1!shows!the!maximum!reachable!diameter!in!meter!of!the!different!areas!for!different!
installation!heights.!(M)!!
!!
!!
Detection(range(!
!!
1.2 Operation&and&Display&&
!!
Figure(1:(Surface(mounted(MD(100(!
!
/6):$%.%O%P8738C!
%!
!
!
P%!
G%!
K%!
M%!
1%!
?@-(%!
O%!
.A%!
.,%!
QR@-%!
+@-(%!
O%!
.-%!
.?%!
QA@R%!
R@?(%!
?S?%!
,%!
.R%!
QA@-%!
R@-(%!
?%!
T%!
..%!
Q.@U%!
A@?(%!
+S?%!
US?%!
V%!
Q.@A%!
!
!
/6):$%A%O%P8738C%!
!
!
P%!
G%!
K%!
M%!
1%!
?@-(%!
O%!
O%!
O%!
QR@-%!
+@-(%!
O%!
O%!
O%!
QA@R%!
R@?(%!
,S?%!
US?%!
.-%!
QA@-%!
R@-(%!
US?%!
U%!
T%!
Q.@U%!
A@?(%!
?S?%!
?%!
U%!
Q.@A%!
!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!5!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
!!
Figure(2:(Flush(mounted(MD100!!
!!
!!
1 KNX!connection!terminal!!
2 Programming!button!!!
3 Blue!movement!LED!!
1.3 Scale&Drawings&&
!!
Figure(1:(Surface(mounted(MD100(!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!6!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
!!
Figure(2:(Flush(mounted(MD100!!
!!
!!
!!
!!
!!
!!
!!
2 Communication&Object&Information&&
2.3 Communication&Object&Table&&
Following!communication!objects!are!available!in!MD100.!!
&8%!
&6($%!
W'C4738C%!
DPT%/9;$%!
X$CI7<%!
W:6I=%!
0!!
General!!
In!operation!!
DPT!1.002!!
1!bit!!
CWT!!
1!!
General!!
Presence!slave!1!!
DPT!1.001!!
1!bit!!
CRW!!
2!!
General!!
Presence!slave!2!!
DPT!1.001!!
1!bit!!
CRW!!
3!!
General!!
Presence!slave!3!!
DPT!1.001!!
1!bit!!
CRW!!
4!!
General!!
Presence!slave!4!!
DPT!1.001!!
1!bit!!
CRW!!
5!!
Presence!!
Presence!output!!
DPT!1.001!!
1!bit!!
CRT!!
6!!
Presence!!
Disable!presence!!
DPT!1.001!!
1!bit!!
CRW!!
7!!
Presence!!!
Switch!‘ON’!delay!time!!
DPT!5.005!!
8!bit!!
CRW!!
8!!
Presence!!
Lighting!Stay!‘ON’!time!!
DPT!5.005!!
8!bit!!
CRW!!
9!!
…!!
…!!
!!
!!
!!
10!!
Brightness!!
Measured!value!!
DPT!9.004!!
16!bit!!
CRT!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!7!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
11!!
Brightness!!
Calibration!!
DPT!9.004!!
16!bit!!
CRW!!
12!!
Constant!Light!!
External!brightness!!
DPT!9.004!!
2!byte!!
CRW!!
13!!
Constant!Light!!
Set!point!value!!
DPT!9.004!!
2!byte!!
CRW!!
14!!
Constant!Light!!
Switch!‘ON’!delay!!
DPT!5.005!!
1!byte!!
CRW!!
15!!
Constant!Light!!
Lighting!stay!‘ON’!time!!
DPT!5.005!!
1!byte!!
CRW!!
16!!
Group!1!!
Disable!light!level!control!!
DPT!1.001!!
1bit!!
CRW!!
17!!
Group!1!-!output!!
Switch!light!!
DPT!1.001!!
1!bit!!
CRT!!
18!!
Group!1!-!output!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CRT!!
19!!
Group!1!-!input!!
Switch!light!!
DPT!1.001!!
1!bit!!
CW!!
20!!
Group!1!–!input!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CW!!
21!!
Group!1!–!input!!
Dimming!light!!
DPT!3.007!!
4!bit!!
CW!!
22!!
Group!2!!
Disable!light!level!control!!
DPT!1.001!!
1bit!!
CRW!!
23!!
Group!2!-!output!!
Switch!light!!
DPT!1.001!!
1!bit!!
CRT!!
24!!
Group!2!-!output!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CRT!!
25!!
Group!2!-!input!!
Switch!light!!
DPT!1.001!!
1!bit!!
CW!!
26!!
Group!2!–!input!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CW!!
27!!
Group!2!–!input!!
Dimming!light!!
DPT!3.007!!
4!bit!!
CW!!
28!!
Group!3!!
Disable!light!level!control!!
DPT!1.001!!
1bit!!
CRW!!
29!!
Group!3!-!output!!
Switch!light!!
DPT!1.001!!
1!bit!!
CRT!!
30!!
Group!3!-!output!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CRT!!
31!!
Group!3!-!input!!
Switch!light!!
DPT!1.001!!
1!bit!!
CW!!
32!!
Group!3!–!input!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CW!!
33!!
Group!3!–!input!!
Dimming!light!!
DPT!3.007!!
4!bit!!
CW!!
34!!
Group!4!!
Disable!light!level!control!!
DPT!1.001!!
1!bit!!
CRW!!
35!!
Group!4!-!output!!
Switch!light!!
DPT!1.001!!
1!bit!!
CRT!!
36!!
Group!4!-!output!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CRT!!
37!!
Group!4!-!input!!
Switch!light!!
DPT!1.001!!
1!bit!!
CW!!
38!!
Group!4!–!input!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CW!!
39!!
Group!4!–!input!!
Dimming!light!!
DPT!3.007!!
4!bit!!
CW!!
40!!
HVAC!!
Disable!HVAC!output!!
DPT!1.001!!
1!bit!!
CRW!!
41!!
HVAC!!
Switch!ON!delay!!
DPT!5.005!!
1!byte!!
CRW!!
42!!
HVAC!!
Lighting!stay!ON!time!!
DPT!5.005!!
1!byte!!
CRW!!
43!!
HVAC!!
Switch!!
DPT!1.001!!
1!bit!!
CRT!!
!!
!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!8!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
&
2.4 Communication&Object&Description&&
!!
&8%!
&6($%!
W'C4738C%!
DPT%/9;$%!
X$CI7<%!
W:6I=%!
0!!
General!!
In!operation!!
DPT!1.002!!
1!bit!!
CWT!!
This!object!is!used!to!report!that!device!is!still!alive! and! connected! to! the! KNX! line!by!sending!cyclic!1!bit!
telegrams.!If!a!telegram!is!not!received,!device!may!be!defective!or!KNX!cable!would!be!intercepted.!!!
- Object!will!be!activated!if!“Device!alive!operation!active”!parameter!in!the!General!tab!is!selected!as!
“yes”.!!!
- Telegram!type!(ON!or!OFF)!can!be!selected!via!“In!operation!bit”!parameter!in!General!parameters!
tab.!Cyclic!period!of!transmitted!telegrams!can!be!selected!via!“In!operation!send!interval”!parameter!in!
General!parameters!tab.!!
!!
1!!
General!!
Presence!slave!1!!
DPT!1.001!!
1!bit!!
CRW!!
2!!
General!!
Presence!slave!2!!
DPT!1.001!!
1!bit!!
CRW!!
3!!
General!!
Presence!slave!3!!
DPT!1.001!!
1!bit!!
CRW!!
4!!
General!!
Presence!slave!4!!
DPT!1.001!!
1!bit!!
CRW!!
“Presence! slave! 1,! 2,! 3,! 4”! objects! will! be! visible! according! to! “Number! of! lighting! group”! parameter! in!
“General”!window.!!!
If!required,!4!additional!motion!detectors!can!be!connected!to!the!master!as!slaves!in!order!to!extend!the!
detection!zone.!Presence!information!of!connected!slave!sensors!are!received!via!these!communication!
objects!by!master!sensor.!Slave!sensors!send!the!value!“1”!when!movement!is!present,!otherwise!send!
value!“0”.!These!values!are!processed!in!OR!gate!by!master!sensor.!If!the!output!value!is!“1”,!master!sensor!
accepts!that!there!is!movement!in!area.!In!other!words!master!sensor!ascertains!“overall!presence”.!!
!!
Note:!Only!one!slave!sensor!should!be!in!relation!with!one!communication!object.!Lights!can!stay!“ON”,!if!
slave!sensors!are!disconnected!from!KNX!line!before!the!master!sensor!is!switched!off.!!
5!!
Presence!!
Presence!output!!
DPT!1.001!!
1!bit!!
CRT!!
Presence!information!of!detector!is!sent!via!this!object.!Cyclic!period!of!object!can!be!selected.!This!object!
has!a!short!reaction!time!(15s,!30s)!so!that!detection!tests!can!be!done!easily.!!
- Object!value!is!“1”!if!movement!is!present.!!
- Object!value!is!“0”!if!there!is!no!movement.!!
!!
6!!
Presence!!
Disable!presence!!
DPT!1.001!!
1!bit!!
CRW!!
Presence!output!object!can!be!disabled/enabled!via!this!object.!!
- A!write!should!be!made!to!the!object!with!value!“1”!to!disable.!!
- A!write!should!be!made!to!the!object!with!value!“0”!to!enable.!!
!!
7!!
Presence!!!
Switch!“ON”!delay!time!!
DPT!5.005!!
8!bit!!
CRW!!
This!object!is!only!visible!if!the!"Switch-on!delay!and!stay-on!time!change!by!bus"!parameter!is!set!to!"yes"!in!
the!"Presence"!parameter!window.!!
This!object!is!used!to!receive!presence!detection!switch-on!time!(in!seconds)!by!the!bus.!After!a!detection,!
sensor!waits!until!“Switch!ON!delay!time”!is!expired!and!sends!the!presence!information!to!“Presence!
output”!with!a!secondary!detection.!!!
!!
!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!9!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
8!!
Presence!!
Lighting!stay!‘ON’!
time!!
DPT!
5.005!!
8!bit!!
CRW!!
This!object!is!only!visible!if!the!"Switch-on!delay!and!stay-on!time!change!by!bus"!parameter!is!set!
to!"yes"!in!the!"Presence"!parameter!window.!!
This!object!is!used!to!receive!Lighting!stay-on!time!(in!seconds)!by!the!bus.!Detector!sends!“on”!
telegram!via!presence!output!object!at!detected!movement!and!stays!“ON”!until!the!adjusted!
time!runs!out.!!
!
10!!
Brightness!!
Measured!value!!
DPT!
9.004!!
16!bit!!
CRT!!
This!object!is!only!visible!if!the!"Enable!brightness"!parameter!is!set!to!"yes"!in!the!"General"!
parameter!window.!!
“Measured!value”!can!be!send!to!the!bus!“on!change!or/and!cyclically”!by!this!object.!!
!
11!!
Brightness!!
Calibration!!
DPT!
9.004!!
16!bit!!
CRW!!
This!object!is!only!visible!if!the!"Enable!brightness"!parameter!is!set!to!"yes"!in!the!"General"!
parameter!window.!!
For!an!optimum!function!of!constant!light!control!a!calibration!of!the!sensor!for!brightness!
detection!is!required.!Current!brightness!value!of!detection!range!of!the!sensor!must!be!written!
to!calibration!object!as!a!new!lux!value.!Sensor!will!calculate!the!calibration!factor!according!to!
new!lux!value!automatically.!Subsequent!detections!will!be!calculated!with!new!calibration!factor.!!
!
12!!
Constant!Light!!
External!Brightness!!!
DPT!
9.004!!
2!byte!!
CRW!!
This!object!is!only!visible!if!the!"Used!brightness"!parameter!is!set!to!"external"!in!the!"Constant!
light!level"!parameter!window.!!
External!brightness!object!is!used!to!receive!brightness!value!for!constant!light!control!from!an!
external!daylight!sensor.!!
!
13!!
Constant!Light!!
Set!point!value!!
DPT!
9.004!!
2!byte!!
CRW!!
This!object!is!only!visible!if!the!"Set!point!type"!parameter!is!set!to!"with!parameter!and!object"!
in!the!"Constant!light!level"!parameter!window.!!
Set!point!value!for!constant!light!level!control!can!be!written!to!this!object.!Any!value!received!
outside!the!permissible!range!of!10…1000!lux!will!be!exchange!to!closest!limit!value.!!
!
14!!
Constant!Light!!
Switch!‘ON’!delay!!
DPT!
5.005!!
1!byte!!
CRW!!
This!object!is!only!visible!if!the!"ON!times!change!by!bus"!parameter!is!set!to!"yes"!in!the!
"Constant!light!level!-!Lighting"!parameter!window.!!
After!a!detection,!sensor!waits!to!start!constant!light!level!until!“Switch!ON!delay!time”!is!expired.!
Current!“Switch!On!delay!time”!can!be!read!from!the!object!or!a!new!“Switch!on!delay!time”!can!
be!written!to!the!object.!Any!value!received!outside!the!permissible!range!of!0…30!is!rejected.!!!
!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!10!/!21!!
Product Manual MD
!
100!
!
EAE KNX Motion Detector !
!
!
!
MD!
100!
PM R!
1.0!
!
15!!
Constant!Light!!
Lighting!stay!‘ON’!
time!!
DPT!
5.005!!
1!byte!!
CRW!!
This!object!is!only!visible!if!the!"ON!times!change!by!bus"!parameter!is!set!to!"yes"!in!the!
"Constant!light!level!-!Lighting"!parameter!window.!!
This!object!is!used!to!receive!Lighting!stay-on!time!(in!minutes)!for!constant!light!level!of!group!1.!
Detector!sends!“on”!telegram!to!output!object!at!detected!movement!and!stays!“ON”!until!the!
adjusted!time!runs!out.!Current!“Lighting!stay!ON!time”!can!be!read!from!the!object!or!a!new!
“Lighting!stay!ON!time”!can!be!written!to!the!object.!Any!value!received!outside!the!permissible!
range!of!0…120!is!rejected.!!!
16!!
Group!1!!
Disable!light!level!
control!!
DPT!
1.001!!
1bit!!
CRW!!
Light!level!control!of!group!1!can!be!disabled!by!this!object.!Group!1!stops!the!sending!light!level!telegrams!
after!disabling.!!
Disable!:!1!!
Enable!:!0!!
!
NOTE:!Group!1,!Group!2,!Group!3!and!Group!4!are!identical!groups.!All!parameters!of!group!1!are!in!use!for!
additional!groups!(group!2,!group!3!and!group!4)!except!offset!values.!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!11!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
!!
17!!
Group!1!-!output!!
Switch!light!!
DPT!1.001!!
1!bit!!
CRT!!
This!object!is!always!available.!“Switch!light”!object!must!be!linked!with!the!switching!object!of!the!actuator!
used!in!conjunction!with!Group!1-lighting!for!switching!ON!and!OFF.!It!is!possible!to!request!the!switching!
status!from!the!detector.!!
!!
18!!
Group!1!-!output!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CRT!!
This!object!is!only!visible!if!the!"Operating!mode"!parameter!is!set!to!"constant!light!control"!in!the!Constant!
light!level"!parameter!window.!!!
This!object!must!be!linked!with!dimming-level!object!of!the!actuator!used!for!dimming!lighting!group!1.!
“Group!1!–!input!Dimming!level”!object!can!increase/decrease!the!output!of!this!object!according!to!
parameters.!!
!!
19!!
Group!1!-!input!!
Switch!light!!
DPT!1.001!!
1!bit!!
CW!!
This!object!is!always!available.!It!must!be!linked!with!switching!object!of!button!that!enables!a!room!user!to!
control!lighting!group!1.!!
Receiving!a!telegram!through!this!object!has!an!alterable!behaviour!according!to!“Light!level!control”!
parameter!in!the!“Constant!light!level”!parameter!window.!!!
!!
Disable(constant(light(and(dim:!It!remains!disabled!until!detector!itself!ascertains!no!person!is!left!in!the!
room,!re-enables!the!constant!light!control!and!switches!the!lighting!OFF.!!!
!!
Don’t(disable(and(no(action:(No!action!receiving!a!telegram!through!Group!1!-!input!object.!!
!!
20!!
Group!1!–!input!!
Dimming!level!!
DPT!5.001!!
8!bit!!
CW!!
This!object!is!only!visible!if!the!"Operating!mode"!parameter!is!set!to!"Constant!light!control"!in!the!
Constant!light!level"!parameter!window.!!!
Lighting!groups!which!are!linked!to!dimming!output!of!Group!1!can!be!dimmed!to!brightness!level!by!this!
object.!!
Receiving!a!telegram!through!this!object!has!an!alterable!behaviour!according!to!“Light!level!control”!
parameter!in!the!“Constant!light!level”!parameter!window.!!!
!!
Disable(constant(light(and(dim:!It!remains!disabled!until!detector!itself!ascertains!no!person!is!left!in!the!
room,!re-enables!the!constant!light!control!and!switches!the!lighting!OFF.!!!
!!
Don’t(disable(and(no(action:(No!action!receiving!a!telegram!through!Group!1!-!input!object.!!
!!
21!!
Group!1!–!input!!
Dimming!light!!
DPT!3.007!!
4!bit!!
CW!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!12!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
This!object!is!only!visible!if!the!"Operating!mode"!parameter!is!set!to!"constant!light!control"!in!the!Constant!
light!level"!parameter!window.!!!
It!must!be!linked!with!relative!dim!object!of!button!that!enables!a!room!user!to!dim!lighting!group!1.!!
Receiving!a!telegram!through!this!object!has!an!alterable!behaviour!according!to!“Light!level!control”!
parameter!in!the!“Constant!light!level”!parameter!window.!!!
!!
Disable!constant!light!and!dim:!It!remains!disabled!until!detector!itself!ascertains!no!person!is!left!in!the!
room,!re-enables!the!constant!light!control!and!switches!the!lighting!OFF.!!!
!!
Don’t!disable!and!no!action:(No!action!receiving!a!telegram!through!Group!1!-!input!object.!!
!!
!!
!!
3 Parameters&&
“Parameters”!chapter!describes!ETS!parameters!of!the!device.!Please!find!detailed!descriptions!of!
communication!objects!in!2.2!Communication!Object!Descriptions.!1$56':7%;6"6($7$"=!are!written!in!
bold!letters.!!
3.3 General&&
!!
General(Parameters(!
Detector'mode'!
*master'!
((slave'!
Operating!mode!of!the!detector!can!be!changed!to!“master”!or!“slave”!by!this!parameter.!!!
Master!:!Detector!will!operate!as!a!master!or!single!detector.!If!there!is!no!slave!sensor!which!is!in!
relation!with!master,!it!will!operate!as!a!single!detector.!In!master!mode,!slave!sensors!are!used!to!
extend!detection!zone.!(Presence!information)!Only!the!master!sends!light!level!telegram!and!HVAC!
telegram.!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!13!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
Slave!! :!Slave!sensors!only!deliver!presence!information!to!the!master!in!order!to!extend!
detection!zone!of!master!sensor.!!
Number'of'slave'!
*no'slave(!
((1(((!
((2(!
((3(!
((4'!
If!detector!mode!is!selected!as!master,!parameter!will!be!visible.!“Presence!slave!1…4”!objects!will!be!
created!according!to!number!selected.!!
Enable'presence'!
*yes'((
no'!
Parameter!enables/disables!presence!parameters!and!objects.!!
Enable'temperature'!
*no'!
%%yes(!
Parameter!enables!presence!parameters!and!objects.!!
Enable'brightness'!
*no'!
''yes'!
Parameter!enables!brightness!parameters!and!objects.!!
Enable'HVAC'!
*no'!
''yes'!
Parameter!enables!brightness!parameters!and!objects.!!
Overwrite'settings'for'download'!
*'yes'''
no(!
This!parameter!is!used!to!decide!whether!settings!stated!below!are!overwritten!or!not!by!
downloading!application!to!the!device.!!!
!Presence!!! !! :!stay!on!time,!delay!time!!
Constant!light!control!!:!stay!on!time,!delay!time,!set!point,!calibration!value!!
! HVAC!! !! !! :!stay!on!time,!delay!time!!
1$234$%6:32$%8;$"6738C%64732$%!
((yes(!
*no'!
This!object!is!used!to!report!that!device!is!still!alive!and!connected!to!KNX!line.!(Heartbeat)!If!alive!
telegram!is!not!received,!device!may!be!defective!or!KNX!cable!can!be!disconnected.!If!parameter!is!
selected!“yes”,!following!parameters!come!up.!!
HC%8;$"6738C%26:'$%!
*send'value'“0”'((
send(value(“1”%!
Telegram!value!can!be!selected!as!“1”!or!“0”.!!
!;$"6738C%=$C#%3C7$"26:%Y=$4Z%%%%%%%%%%%%%%%%%%%%%%!!
1…*300…65535(!
Telegram!value!is!sent!cyclically!according!to!time!interval.!!
!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!14!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
3.4 Presence&&
!!
Presence(Parameters(!
Blue'LED'!
*show'movement'!
''off(!
%!
If!“show!movement”!is!selected,!blue!LED!inside!the!detector!lights!up!with!movement!detection.!!
Presence'switch'‘ON’'delay'[sec]'!
*0…5'!
%!
Parameter!defines!presence!detection!switch-on!time!(in!seconds).!After!a!detection,!sensor!waits!
until!“Switch!ON!delay!time”!is!expired!and!sends!the!presence!information!to!“Presence!output”!
with!a!secondary!detection.!!
Min.'number'of'movements'detected'
during'switch'‘ON’'delay'!
*1…20'!
%!
“Presence!switch!ON!delay”!is!started!after!detecting!first!movement.!Detector!waits!for!selected!
number!of!movements!during!“Presence!switch!ON!delay”!time!in!order!to!send!that!the!presence!
information!is!“ON”.!!
Presence'stay'‘ON’'time'[sec]'!
1…*10…255'!
This!parameter!defines!lighting!stay-on!time!(in!seconds).!Detector!sends!“on”!telegram!via!presence!
output!object!at!detected!movement!and!stays!“ON”!until!the!adjusted!time!runs!out.!!!
Break'in'presence'detection[sec]'!
*0…255(!
Movements!detected!are!ignored!during!the!period!selected.!This!parameter!is!used!to!avoid!
incorrect!detections!if!temperature!changes!after!lights!switched!“OFF”.!!!
Switch'‘ON’'delay'and'stay'‘ON’'time'can'
be'changed'by'bus'!
*no'!
((yes%!
If!parameter!is!selected!“yes”,!“Switch!ON!delay!time”!and!“Lighting!stay!ON!time”!communication!
objects!will!be!visible.!!
Send'presence'cyclically'!
*inactive'!
((15s(!
((30s(!
((1(min(!
((5(min(!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!15!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
!
10(min(!
15(min(!
30(min(!
60(min%!
Presence!information!will!be!sent!cyclically!in!selected!period!via!“Presence!output”.!!
Disable'presence'output'!
*no'!
''ON(for(disabling(/(OFF(for(enabling(!
(OFF(for(disabling(/(ON(for(enabling%!
This!parameter!is!used!to!make!visible!“Disable!presence!output”!object!and!which!telegram!to!use!
disable!and!re-enable!presence!output!object.!If!any!parameter!is!selected!except!“no”,!“Disable!
presence!output”!object!will!be!visible.!!!
ON!for!disabling!/!OFF!for!enabling:!Presence!output!is!disabled!with!the!value!“1”!and!re-enabled!
with!value!“0”.!!
OFF!for!disabling!/!ON!for!enabling:!Presence!output!is!disabled!with!the!value!“0”!and!re-enabled!
with!value!“1”.!!
!!
Behaviour'disable'lighting'!
*no'action'!
((Light(ON(!
((Light(OFF%!
This!parameter!is!used!for!selecting!whether!to!send!a!telegram!from!the!“presence!output!object”!
before!disabling!it!and,!if!so,!with!which!value.!!
No!action:!No!telegram!is!sent!before!disabling!presence!output!object.!!
Light!ON:!Presence!output!object!is!set!to!the!value!“1”!before!disabled.!!
Light!OFF:!Presence!output!object!is!set!to!the!value!“0”!before!disabled.!!
Behaviour'enable'lighting'!
*no'action'!
((Light(ON(!
((Light(OFF%!
This!parameter!is!used!for!selecting!whether!to!send!a!telegram!from!the!“presence!output!object”!
before!enabling!it!and,!if!so,!with!which!value.!!
Continue!control:!After!enabling!the!presence!output!object,!detector!keeps!the!current!status!of!
presence!output!object.!!
Light!ON:!After!enabling!the!presence!object,!it!is!set!to!the!value!“1”.!!
Light!OFF:!After!enabling!the!presence!object,!it!is!set!to!the!value!“0”.!!
!!
!!
!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!16!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
3.5 Brightness&&
!!
Brightness(Parameter(!
Send'brightness'on'change'of'!
((inactive((!!
10(lux(!
((20(lux(!
((30(lux(!
((40(lux(!
*50'lux'!
((60(!
'!
This!parameter!is!used!to!select!which!level!the!brightness!value!last!sent!must!have!changed!by!for!
the!brightness!measured!to!be!sent!again.!!
Cyclical'sending'of'light'value'!
*inactive''!
((5s(!
((10s(!
((20s(!
((40s(!
1 min(!
2 min(!
((4(min(!
((6(min(!
((8(min(!
((10(min(!
((15(min(!
((20(min(!
((30(min%!
'!
This!parameter!is!used!to!adjust!cyclical!sending!period!of!“Brightness!value”!object.!!
Calibration'!
*via'object''!
!!with(calibration(factor(!
'!
This!parameter!is!used!select!calibration!method!of!the!brightness!sensor!inside!the!detector.!There!
are!two!options!in!order!to!calibrate!the!brightness!sensor.!!
Via!object:!Calibration!value!is!written!via!“Calibration”!object.!Brightness!value!which!is!measured!by!
a!lux!meter!in!the!detection!range!of!the!sensor!must!be!written!to!the!“calibration”!object!as!a!new!
lux!value.!Adjustment!factor!is!calculated!by!detector.!!
With(calibration(factor:(Detected!brightness!value!is!calibrated!by!calibration!factor!to!current!
brightness!value.!Calibration!factor!only!should!be!written!to!calibration!factor!parameters.!!!
Calibration'factor'('x'0.1)'!
1…[R-…200!!
'!
This!parameter!is!used!specify!the!calibration!factor!of!brightness!sensor.!Any!value!written!outside!
the!permissible!range!of!1…200!is!rejected.!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!17!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
3.6 Constant&light&level&&
!!
Constant(Light(Level(Parameters(!
Operating'mode'!
*Constant'light'control(!
!!Brightness(on/off(control'!
This!parameter!is!used!to!select!operating!mode!of!constant!light!level.!!
Constant!light!control:!Lighting!groups!are!controlled!by!“Dimming!level”!object!until!reaching!the!set!
point!value!for!constant!light!control.!“Switch”!object!is!only!used!to!%100!and!%0!percentages!when!
it!is!needed.!!
Brightness!on/off!control:!Lighting!groups!are!only!controlled!by!“switch”!object!according!to!set!
point!value.!If!measured!brightness!value!is!greater!than!the!set!point!value,!“switch”!object!is!set!to!
the!value!“0”.!If!measured!brightness!value!is!less!than!the!set!point!value,!“switch”!object!is!set!to!
the!value!“1”.!!
Lighting'group'count'!
*1'!
''2(!
((3(!
((4%!
This!parameter!is!used!to!specify!the!lighting!group!count!which!are!controlled!by!constant!light!
function.!!
Set'point'type'!
*parameter'!!
parameter!and!object%!
'!
This!parameter!is!used!selecting!“Set!point!type”.!!
Parameter:!Set!point!is!only!specified!by!parameter!on!ETS.!!
Parameter!and!object:!Set!point!is!specified!by!parameter!on!ETS,!it!also!can!be!changed!via!“set!
point!value”!object!by!bus.!!!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!18!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
Used'brightness'!
*internal'!!
external%!
'!
This!parameter!determines!that!brightness!val!
internal!or!external.!!!
ue!which!is!used!for!constant!light!con!
trol!will!be!!
Maximal'variation'from'set'point'value'!
((15(lux(!
*30'lux'!
((45(lux(!
!!60!lux!!
'!
This!parameter!is!used!to!adjust!hysteresis!value!for!set!point!value.!(-30…set!point!value…+30)!
Dimming!level!is!only!sent!by!“dimming!level”!object!if!current!brightness!value!is!out!of!the!range!
specified!with!maximal!variation!of!set!point!value.!!
Max'step'size'for'dimming'!
((0.5%(((
1%(!
!!1.5%!!!
2%!!
!!2.5%!!!
3%!!
[?\%!
%!
This!parameter!is!used!to!select!step!size!dimming!for!constant!light!control.!“Dimming!level”!object!
sends!the!dimming!values!(1!byte)!with!selected!step!size!to!reach!the!appropriate!brightness!in!the!
room!for!set!point!value.!(%100,!%95,!%!90!etc.)!!
Transmit'next'dimming'value'after'!
((0.5s(!
*1s'!
!!2s!!
!!3s!!
!!5s%!
%!
This!parameter!is!used!to!specify!the!time!interval!between!two!sending!dimming!value.!After!
sending!a!dimming!value!(%60),!next!dimming!value!(%55)!will!be!sent!after!the!time!interval!
selected.!!!
Finish'constant'light'level'control'with''!
*only'dimming'value'telegram'!!
switching(off(!
'!
This!parameter!defines!the!way!in!which!constant!light!level!control!will!end.!!
Only!dimming!value!telegram:!If!there!is!sufficient!ambient!light!in!a!room,!constant!light!level!
control!is!ended!by!only!dimming!value!telegram.!!
Switching!off:!If!there!is!sufficient!ambient!light!in!a!room,!constant!light!level!control!is!ended!by!
switch!(OFF)!telegram.!!
Lighting'group'X'offset'to'dimming'level'
for'group'1'!
-100…[-…100%!
This!parameter!is!used!to!express!offset!value!of!additional!Lighting!Group!X!(X:!2,!3,!and!4)!according!
to!“Lighting!Group!1”.!An!offset!parameter!will!be!created!for!every!additional!lighting!group.!!
Lighting'level'control'!
*disable'constant'light'and'dim'!!
don’t!disable!and!no!action%!

!
!©EAE!Technology!!! !! !! www.eaetechnology.com!!! !! !! Page!19!/!21!!
Product Manual MD!
100!
!
EAE KNX Presence Detector
!
!
!
!
MD!
100!
PM R!
1.0!
!
This!parameter!is!used!to!select!the!behaviour!of!lighting!level!control!when!any!telegram!is!received!
via!input!objects!of!related!lighting!group.!(Input!switch,!input!dimming!level,!input!dimming!light)!!
Disable!constant!light!and!dim:!When!input!telegram!is!received,!constant!light!level!control!will!be!
disabled!until!re-enabling!via!“Disable!constant!light”!object!of!the!lighting!group!and!lighting!group!
will!be!dimmed.!!
Don’t!disable!and!no!action:!Constant!light!control!is!not!disabled!when!any!input!telegram!is!
received.!Lighting!group!performs!the!command!which!is!sent!by!input!until!to!next!constant!light!
level!telegram.!!
3.7 Lighting&&
!!
Lighting(Parameters(!
Lighting!section!consists!of!presence!detection!parameters!which!will!be!used!for!constant!light!level!
control.!!
Operation'lighting'!
*automatically'‘ON’'and'‘OFF’'!!semi-
automatic(only(‘OFF’'!
This!parameter!is!used!to!select!operation!type!of!lighting.!!
Automatically!‘ON’!and!‘OFF’:!Lighting!group!is!controlled!automatically!by!detector!according!to!
presence!information.!If!person!is!present!in!the!room,!“ON”!command!is!sent!to!the!lighting!group!if!
no!person!is!present,!“OFF”!command!is!sent!to!the!lighting!group.!!
Semi-automatic!only!‘OFF’:!Lighting!group!is!controlled!semi-automatically!according!to!presence!
information.!The!lighting!group!waits!the!“ON”!command!from!user!in!order!to!light!up,!it!does!not!
light!up!even!if!a!motion!is!detected.!!But,!“OFF”!command!is!sent!automatically!by!detector!if!there!
is!no!person!in!the!room.!!!
Switch'‘ON’'delay'[min]'!
[-…30%!
This!parameter!is!used!to!determine!“Switch!ON!delay!time”.!After!a!movement!detection,!sensor!
waits!until!“Switch!ON!delay!time”!is!expired!and!sends!the!presence!information!to!“Presence!
output”!with!a!secondary!detection.!!!!
Stay'‘ON’'time'[min]'!
[.…120%!
This!parameter!is!used!to!determine!“Stay!ON!time”!for!lighting!group.!“ON”!telegram!is!sent!to!the!
lighting!group!with!a!detected!motion!and!lighting!group!stays!“ON”!until!“Stay!ON!time”!is!expired.!!
Switch'‘ON’'delay'and'stay'‘ON’'time'can'
be'changed'by'bus'!
*yes'!!
no%!
This!parameter!determines!whether!“Switch!ON!delay!time”!and!“Stay!ON!time”!can!be!changed!by!
bus!or!not.!!