eamlab Element 202i User manual

1
Element202i
Thank’you of purchasing this EamLab product. Who are dedicated to the policy
of creating the highest quality audio components, are proud to introduce. You
can be assured that in preparing this component, every attention was paid in
great detail by our entire staff to strict quality control . This dedication was
followed throughout the wole manufacturing process –from basic research,
the selection of each parts, assembly and testing –so that we could supply a
product with every confidence that it will give full owner satisfaction and pride.
We welcome you to the fast-growning Eam Lab circle of dedicated audio
enthusiasts and true sound lovers
User manual
Element 202i / Element 260Ai

2
The Element 202i is integrated power amplifier in AB class capable to
275Wrms for channel into 8 ohm
Element 260Ai is integrated amplifier in pure Class A capable to 60
Wrms for channel into 8 ohm
Circuit of preamplification consist to digital potentiometer PGA2310
Burr Brown who is currently the best potentiometer in high-end
market. With PGA2310, for buffering signal , is used BurrBrown high
slew/rate Operational amplifier for best audio performance for
transfer signal by input board to output power stage
The integrated amp is structured by dual mono technology with 2
800VA transformer encapsulated with resin and in aluminum
enclosure thus eliminating any possible variation of the original audio
signal which would become dirty through electromagnetic fields.
The main power capacitors are designed on our tight specifications.
They have a very high temperature coefficient and aluminum armor.
Together with the resistors in the metal film 1% tolerance and the
decoupling capacitors in polypropylene audiograde we obtained
results certainly real.,
Features

3
Contents
2…………….Introduction & features
3…………….Table of contents
4…………….Safety instructions
5…………….Use remote control
6…………….Menu and Submenu on display
8…………….Front pannel instruction
9…………….Connections
10 …………….Troubleshooting guide
11 …………….Datasheet
12 …………….guarantee policy

4
1. For best performance, please read
this manual carefully. Keep it in a safe
place for future reference.
2. Install the unit in a cool, dry, clean
place away from windows, heat
sources, intense vibration, dust,
humidity, cold, and sources of
humming (transformers, motors,
etc.).. To prevent fire or shock hazard
do not expose the unit to water and
moisture.
3. Never open the equipment. If
something should get into all 'inside,
contact your dealer.
4. Do not operate the switches and
other controls with force. When
moving the unit, first disconnect the
power cord and cables connected to
other devices. Never pull the wires
themselves.
5. The voltage used must be
specified.
Using this product with a current
whose voltage is higher than
specified is dangerous and may cause
fire or other damage. EAM LAB is not
responsible for any damage due to an
incorrect use of the appliance
6. Always set the VOLUME control to
min. before starting playback of the
audio source. Gradually increase the
volume to an appropriate level after
playback has started.
7. Do not clean the unit with
chemical solvents: this could ruin the
finish. Instead, use a soft, dry cloth or
denatured alcohol.
8. In case of malfunction, before
concluding that the unit needs to be
repaired, consult the chapter on
"TROUBLESHOOTING".
9. If you are not using the unit for
long periods of time (eg for a
vacation), disconnect the power plug
10. During thunderstorms,
disconnect the power cord to avoid
any lightning damage the unit.
11. Grounding or Polarization: take
the necessary precautions to ensure
that the grounding or polarization are
not canceled.
Before you start to use read following information
Safety information

5
Unpacking:
Carefully remove from the box your
amplifier and keep the original
carton and packing materials for
future trips, expeditions or long-term
storage
Before the installation :
remove your amplifier, taking care to
keep it in the future if you ever
require to be shipped to a service
center EAMLAB to be overhauled or
repaired.
package contents:
Verify that the following acessories
are included in the package:
remote control, power cord and this
manual.
Replacing Batteries
If the remote control only works
when it is near the unit, the
batteries are weak. Replace the
batteries with new ones.
Note
For replacement use only
batteries model CR3020.
Make sure the polarity is
correct
For change battery
remove 4 screw in bottom
side and leave the
electronic board . battery
are bottom of printed
circuit
Use remote control
The remote control transmits a
directional infrared beam. During
operation, be sure to point the
remote directly at the infrared
sensor.
When the sensor is covered or there
is a large object between the remote
control and the sensor, the sensor is
not receiving the signals. The sensor
may not be able to receive signals
properly when it is exposed to direct
sunlight or strong artificial light (such
as a fluorescent light or a flashing).
In this case, change the direction of
light or reposition the unit to avoid
direct lighting.
Note
• Handle the remote control
carefully.
• Do not spill water or other liquids
on the remote control.
• Do not drop the remote control.
• Do not leave or put away the
remote control in the following
conditions: - High humidity or
temperature such as near a heater, a
stove or a bathroom; _ Dusty; -
Expose to temperatures very low or
very high

6
Set –button for sub menu
dipaly to command balance and
mono/stereo operation
Pwr –turn on /off preamplifier
DSP –same set button
V+ increase volume
V - decrease volume
Mute –muting signal out
CH+ / Ch- select input
Remote control function
CH+/CH- for changing input source,
V+/V- button for increase or decrease volume
Mute buttom for muting output signals
Pwr for turn on or turn off preamplifier
In the master menu use button:

7
To master menu use DSP or SET button for enter in this menu.
When inside this menu choose button :
Mute for changing MONO/STEREO operating
V+ / V- for changing balance left/right gain
DSP or Set for return to master menu

8
Front pannel functions
LEFT encoder
Rotate to increase or
decrease volume , push to
on/off amplifier
LEFT encoder
Rotate for selected source
input
Status LED to indicated
protection and stand-by
Control Display

9
Connection and functions
Right speaker
8/4 Ohm
Left speaker
8/4 Ohm
Source input
XLR balanced and single-
ended
General
power on/off
switch
Power supply
cord

10
problem
Possible cause
remedy
No power on
The plug on the power
cord is not connected or
is not fully inserted .
The mains fuse is blown
Securely connect the
plug or check the fuse on
the rear panel next to
the socket
No sound
Connecting signal Input
or output cables
incorrect
Check the RCA or XLR
cables and / or the
correct connection
sequence of sources
Distorted sound
The source has an output
signal too high and
preamplifier input is
saturated
Turn down the volume of
the source if it is
equipped with such
control
The signal is low
Switch XLR / RCA on
power amplifier
check the correct
position of the switch for
connecting balanced XLR
or unbalanced RCA
Main fuse is blow
Current overload
replace with identical
fuse. if the fuse blows
again contact service
center
Remote control do not
work
Batteries , objects in
front of receiver
replace batteries or
remove any obstacles in
front of the infrared
receiver
ILP led flashing
Output offset to much
high or power final stage
with problem
Turn off the machine. If
the problem persists,
contact an authorized
service center
Troubleshooting

11
202i / 260Ai Datasheet
Input
1 stereo XLR balanced
3 stereo RCA single ended
Output
2 wbt binding post for channel
XLR input impedance (xlr input)
47 Kohm
RCA input impedance (input
2/3/4)
22 Kohm
Output power 260Ai
60 / 120 Wrms 8/4 ohm in class A
Output power 202i
275 / 500 Wrms 8/4 ohm in AB class
Frequency response
5 hz to 70 Khz +/- 0.3db
70Khz to 120Khz +/- 3db
Volume control
BurrBrown digital potentiometer
PGA2310
Damping Factor
>150 to 8 ohm @ 200Hz for 202i
>80 to 8 Ohm @ 200hz for 260Ai
THD
0.03% full power into 4 ohm for
each models
Signal to noise ratio
>105 Db
Power consumption
Stand-by : 1W for 202i /260Ai
Idle : 20W for 202Ai
120W for 260Ai
Maximum: 1100W for 202i
240W for 260Ai

12
How to expedite service
Return Authorization Procedure
If you believe there is a problem with your
component, please contact your dealer,
distributor, or the EamLab factory to discuss
the problem before you return the
component for repair. To expedite service,
you may wish to complete and e-mail the
Service Request Form in the Service section
of our website at:
www.eamlab.com
To contact EamLab service
Tel. [phone]
MAIL : [email protected]
Website : www.eamlab.com
How to return a product
To return a product to EAMLAB, please follow this procedure so that we may
serve you better: 1. Obtain a Return Authorization Number (R/A number) and
shipping address from the Krell Service Department. 2. Insure and accept all
liability for loss or damage to the product during shipment to the Krell factory
and ensure all freight (shipping) charges are prepaid. The product may also be
hand delivered if arrangements with the Service Department have been made
in advance. Proof of purchase will be required for warranty validation at the
time of hand delivery