E&M PM-01 User manual

If you experience any difficulties with your equipment, have questions or suggestions, please contact
Technical Support at… [e-mail]
© 1995-2019 E&M Machining, Inc
765-754-3613 - discountsoapequipment.com - emmachining.com
Frankton, Indiana Made in the USA
Page 1of 3
Professional
All Purpose Melter
Instruction Manual
Model: PM-01
Important Safeguards
To reduce the risk of personal injury or property damage, when using electrical appliances basic
safety precautions should always be followed, including the following:
•Read all instructions.
•Make sure nothing is plugged in until water is completely covering the element
•The outside of the melter will get HOT, use caution and keep children and pets away.
•Unplug from outlet when not in use and before cleaning. Allow cooling before putting on
or taking off parts, and before cleaning.
•SAVE THESE INSTRUCTIONS

If you experience any difficulties with your equipment, have questions or suggestions, please contact
Technical Support at… [e-mail]
© 1995-2019 E&M Machining, Inc
765-754-3613 - discountsoapequipment.com - emmachining.com
Frankton, Indiana Made in the USA
Page 2of 3
Important notes for the All Purpose Melter:
•Please read all instructions before attempting to set-up your Melter.
•Put enough water in it to check for leaks.
•Keep about 2” of water above the perforated, stainless steel plate.
•Do not use an extension cord or power strip.
•Hard Water or Water that may cause corrosion to your element… If you have this type of tap water
or you are in doubt use RO water, distilled or bottled water.
•Consider hiring an Electrician or Plumber to install your tank.
DO NOT PLUG IN UNTIL THE ELEMENT IS COMPLETELY SUBMERGED IN WATER!
THERE IS NO FIRE HAZARD BUT IT WILL DESTROY YOUR ELEMENT.
Heater/Thermostat Installation:
•Your Heater/Thermostat is supplied with a cord and plug.
o1500 Watt Heaters are 120 volts and use a standard 3-prong plug.
•If wiring direct to an outlet or electrical panel hire an Electrician.
International Customers; you will need to use the proper style plug for your country. If
you are not sure, consult an electrician.
Note: Make Sure All threads have been wrapped with Teflon Tape
1. Insert the Heater Tube into the 1 ¼” (32mm) Coupling. Make sure it fits in
freely. Note: the Coupling is a female fitting
2. Screw the Heater/Thermostat into the Coupling.
3. Turn the Heater/Thermostat until it is tight and the cord is not at the bottom of the box. See Picture
Below.
4. Installing the Capillary Bulb and Tube:
oCarefully… uncoil about 18” (46cm) of the Capillary Tube. Do
not kink or make any sharp bends in it.
oLocate the Capillary Tube Inlet, left of the Heater Box.
oInsert the Capillary Bulb into the hole all the way in until it
stops.
oSlide the Capillary Tube Plug down the tube and push it
firmly into the hole. This will lock the Capillary Tube in place
and seal the hole.
oCarefully coil up the excess Capillary Tube and secure it with
a piece of tape or tie-wrap behind the box.
oBe careful that you do not bend or kink the Capillary Tube.
Heater Box
Power Cord
Capillary Tube
Thermostat Dial

If you experience any difficulties with your equipment, have questions or suggestions, please contact
Technical Support at… [e-mail]
© 1995-2019 E&M Machining, Inc
765-754-3613 - discountsoapequipment.com - emmachining.com
Frankton, Indiana Made in the USA
Page 3of 3
Cautions using your Tank
•The Tank walls can get very hot, Be Careful.
•Keep the cord out of the way of traffic and not where someone might trip over it.
•Keep children away from the tank and electrical components.
•Do not drop water on the control box.
•When moving the tank, let it cool and drain it completely.
•Do not use an extension cord or power strip.
•Safety first!
Troubleshooting your Tank, if it is not heating:
First, check the following.
•Is the unit plugged in?
•Check the cord and plug. Are they in good shape, not cut or damaged?
•Has the Breaker been tripped or a fuse blown?
•Try a lamp or something else that you know works, will work in the outlet?
Call an Electrician or Plumber, if you do not know what you are doing. All tanks are tested prior to shipment.
If it is not heating, then it might not be installed correctly or something in the circuit providing the power is not
correct.
Check the Heater/Thermostat box.
BEFORE TESTING YOUR ELEMENT, UNPLUG YOUR HEATER/THERMOSTAT!
You can download instructions for checking and replacing your element at…
https://discountsoapequipment.com/Parts_c_22.html
Capillary Bulb
goes in this tube next
to heating element.
Perforated, stainless
steel plate