Easy@Home EBP-020 User manual

EBP-020
Blood Pressure Monitor
User Manual

Foreword
Dear user :
Thank you for choosing the easy@Home blood pressure monitor
(EBP-020). Please read this manual carefully before use and keep
for future reference. The blood pressure monitor is suitable for
adults. People 12~18 years old should be accompanied by an adult
when taking measurements.
Summary :
The blood pressure monitor consists of the main body and a large
cuff. It is suitable for measurement of human systolic pressure,
diastolic blood pressure and pulse. The blood pressure values
obtained by this equipment are equivalent to those measured with
the auscultatory method. (The auscultatory method is auscultatory
method where a trained healthcare provider uses a blood pressure
meter and listens for the blood flow sounds using a stethoscope.)
The blood pressure monitor includes intelligent pressurization,
automatically pressurizing to an appropriate pressure value accord-
ing to your blood pressure, effectively reducing the discomfort
caused by incorrect pressure, shortening the measuring time, and
prolonging the service life of the cuff.
The blood pressure monitor is equipped with the memory capacity of
99 measurements each for two users, and the data of the two users
can be saved separately.

Contents
1. Indications for Use..................................................................... 1
2. Monitor Components ................................................................. 1
3. Before Use ................................................................................ 3
4. Setting Up Your Device ............................................................. 4
5. Measurement ............................................................................ 7
6. About Blood Pressure ............................................................. 11
7. Contraindications, Precautions, Warnings and Prompt Instructions
...................................................................................................... 13
8. Q & A. .................................................................................... 17
9. Troubleshooting....................................................................... 19
10. Cleaning and Disinfection ....................................................... 21
11. Storage ................................................................................... 23
12. Product Specification .............................................................. 23
13. Precautions............................................................................. 25
14. Statement of Electromagnetic Compatibility ........................... 26

1. Indications for Use
2. Monitor Components
The blood pressure monitor is intended to measure the systolic
pressure and diastolic pressure, as well as the pulse rate of an adult
via the non-invasive oscillometric method(Oscillometric Method is
measured by establishing the relationship between systolic blood
pressure, diastolic blood pressure, mean blood pressure and cuff
pressure oscillation wave.) at medical facilities or at home.
-1-
Air jack
User key
Start / Pause key
USB external
power supply
port
Memory key

Display Screen
Note: Arrhythmia Indicator will be displayed when the user has tested
for arrhythmia.
Average value Symbol appears when you view historical measure-
ments. When you look at historical records, the first value that
appears is the average of the latest three measurements.
-2-
1
2
KPa
mmHg
M
AVG
User icon
Date / time display
Unit of Measurement
Blood Pressure
Level Indicator
Low battery icon
Memory icon
Memory Number
Average value SymbolArrhythmia Indicator
Pulse
Heartbeat icon
Diastolic
pressure
Systolic
pressure

3. Before Use
(1) Install the Battery :
Open the battery cover and install
the batteries in the battery
comparement.
The battery compartment is
positioned at the bottom of the
electronic blood pressure monitor.
-3-
(a) Open the battery cover according to the method shown in the
figure above.
If the low battery symbol appears on the screen after the product
is turned on, the measurement cannot be performed, and the batter-
ies must be replaced.
(b) Place 4 AAA dry batteries in the battery compartment, and pay
attention to the correct polarity of the batteries. Install the battery as
indicated in the picture immediately below:
(2) Battery power indication and replacement
Please use 4 AAA alkaline dry batteries.

4. Setting Up Your Device
-4-
(3) USB connection for power supply
(1) Selecting User
Do not use any expired batteries.
If the product is not used for a long time (over 3 months), please
take out the batteries to avoid battery corrosion and danger to
device.
Optional (Not Included): The product’s power can be supplied through
a DC 5V external power supply through the USB port.
(4) Cuff
The arm circumference rang of the cuff is 22-42cm.
To connect: Insert the air plug on the cuff into the air jack on the left
side of the electronic blood pressure monitor, as shown in the follow-
ing figure:
Air jack
Air plug
Air tube
Cuff

a.Press the "User " key for 3 seconds to enter the setting mode.
b.Press the "User " key to enter the year setting mode (or automat-
ically enter the year setting mode after the batteries are reloaded and
the product is powered on). The screen displays 20XX and flickers
continuously.
c.Press the "Memory " key to increase the value, between 2019
and 2039. Press the "User " key for confirmation and enter the
month setting mode. After entering the month setting mode, the
screen will display xx-xx and flash the month.
d.Press the "Memory " key to increase the value between 1 and
12. Press the "User " key for confirmation and enter the date
setting mode. After entering the date setting mode, XX-XX is
displayed on the screen and flickers on the date display.
-5-
(2) Year & month / Date setting
(Note: While the blood pressure monitor is off, press "User " key
to view the current time and the current user)
While the device is off, press the "User " key for 3 seconds, the
screen displays "User 1 " or "User 2 ", and flickers continuou-
sly. Press the "Memory " key to switch to the other user. (System
default user: User 1 )
While the device is off:
press the
“Memory”
key
Switch over

e.Press the "Memory " key to increase the value, between 01 and
31. Press the "User " key for confirmation and enter the time setting
mode.
-6-
(3)Measurement Unit Setting
Note: When you change the battery, year/month/day/time may disappear
to restore the factory settings. But the historical data measured will
not be lost. If this happens, please follow the above steps to reset
year/month/day/time.
In this mode, the SYS area will display " ", and the measurement
unit area will display mmHg, meaning the unit mmHg is selected
press the
“Memory”key Adjust Setting
Press the
"User" key Confirm
Adjust
Setting
Adjust
Setting
Adjust
Setting
Confirm Confirm
Confirm

(system default unit: mmHg).
At this time, pressing the "Memory " key will switch the unit selection
to the unit kPa. After selecting the unit, press the "User " key again
to confirm.
5. Measurement
-7-
(1)Before Measurement:
(2)Precautions for most accurate results
--Keep the conditions of your measurements consistent.
--The measurement should be carried out in a quiet environment.
Avoid eating, smoking or any form of heavy physical labor, as it will
affect the measurement result.
Sit on a chair to have a rest for about 10min in a quiet environment.
Clear the clothing from the arm for measurement.
Also, measure the same arm for consistency (generally the left arm,
because the left arm is closer to the heart). Measure at approximate-
ly the same time each day because can change throughout the day.
Requirement: Please read the user manuals carefully before use.
mmHg mode KPa mode