Easy CDV43 User manual

2-Wire Video Intercom System
CDV43 USER MANUAL(EN)
Read this manual carefully before using the product, keep in a safe place for future use.

1
145~160 cm
LCD Screen
Microphone
Talk/Mon Button
Menu Button
Up Button
Close Button
Return Button
Down Button
Mute Button/Indicator
Unlock Button
Connection Port
Mounting Hook
1 2
sw+sw-RINGGNDNC
3
ON
L1L2
DIP
4 5 6
1 2
sw+sw-RINGGNDNC
3
ON
L1L2
DIP
4 5 6
1 2
SW+SW-RINGGNDNC
3
ON
L1L2
DIP
4 5 6
SW+,SW-: Door bell call button
connection port.
Ring,GND: Extra buzzer connection
port.
NC: Reserved.
L1 & L2: 2 wire Bus terminal.
DIP switches: Total 6 bits can be
configured.
Bit1~Bit5: Used to set User Code.
Bit6: Set to ON when the monitor is at
the end of the line (EOL) or operates
with a DBC4A otherwise, set to OFF.
2.Monitor Mounting
1.Parts and Functions
Terminal Description

2
00:23
DS-1
4. When the monitor is in standby mode, press'Talk/Mon'button (or select 'Monitor
by Select'button on the main menu, press 'Menu button to confirm, the 'Select
3. During talking state, Press' Unlock'button to release door #1.
2. Press ' Talk/Mon'button on monitor, you
can communicate hands free with the visitor
for 90 seconds. After finishing communication,
press ' Talk/Mon'button again (or press
' Close button) to end the communication. If
nobody answers the phone, the screen will be turned off automatically after 40 seconds.
1. Press 'CALL'button on the outdoor station,
the Monitor rings and the screen will display the
visitors' image.
Press Menu / Close button in
standby mode, the main menu page will be
shown as follows:
1. Use the screws provided to fix the Mounting Bracket (fits a standard UK single gang
flush back box if required). Fitting accessories includes a Bracket (Two x M4x25mm
screws are needed for fastening the Mounting Bracket), 1 x green connector to connect the
bus line to the Monitor)
2. Wire the system correctly (please refer to the connection chapter) then fit the Monitor to
the Mounting Bracket firmly.
a Camera'page will be displayed, the / button can then be used to select
the camera view required .
4. Basic Door Release Operation
3. Main Menu

3
Use / Button to selete
the item you want, then
press Menu button to call.
Namelist Call
Select Intercom
Inner Call
Call Guard Unit
[01]
Namelist Call
[03]
[04]
[02]
[01]
Monitor By Select
Main Menu
Divert Call
Don’t Disturb
Intercom Call
2.The DIP switch code of the monitors must be different.
Use / button to select
Intercom Call, then press
Menu button to
confirm.
Calling.
2. Inner Call:If multiple Monitors are installed in
at the same
time.Note: The DIP switches setting of all monitors must be same.
the same apartment, select Inner Call, all
the other Monitors will ring at the same time, whichever Monitor answers the
call, conversation is started, and the other monitors will stop ringing
3. Call Guard Unit:A Monitor can be assigned as Guard Unit Monitor; when the Guard
Unit Monitor answers the call, conversation with the guard person is started.
When the monitor is in standby mode, press ' Menu button to enter main menu page. Use /
button to move up/down to select 'Intercom Call' , press ' Menu'button to enter the 'Select
Intercom' page, there are 3 options available.
1. Namelist Call:A user in one apartment can call other apartments in the system.
the namelist will be created automatically by the system. Use ' / ' button to select a
name on the screen then press ' Menu'button to call. Function is disabled by default.
Note: 1. Press "MENU" button again to redial.
Use / Button to select
Namelist Call,then
press Menu button
to confirm.
5. Intercom Function

Monitor By Select
Main Menu
Divert Call
Don’t Disturb
Intercom Call
Normal
No Disturb
8 H
Always
1 H
4
Monitor By Select
Main Menu
Divert Call
Don’t Disturb
Call Divert Options
Simultaneously
Setup Tel Numbers.
If No Answer
No Divert
Intercom Call
Use / button to select
'Don't Disturb' option, then
press Menu button to
confirm.
Use / Button to select the
option you want, then press
Menu button to confirm.
Use / Button to select the
option required, then press Menu
button to confirm.
When the monitor is in standby mode, press Menu Button to enter main menu page.
Use / button to move upward / downward to select Divert Call item, press Menu
Buttonto enter the call divert options page, you have 4 items to select.
Use / button to select Divert
Call the press Menu button
to confirm.
6. Divert Call Function (Requires CDV-GSM)
7. Do Not Disturb Function
When the monitor is in standby mode, press Menu Button to enter main menu page. Use /
button to move up / down to select 'Don't Disturb' , press Menu button (or press Mute
button/indicator directly) to enter the 'No Disturb' page, there are 4 options.
1. No Divert----calls from outdoor station will not be diverted.
2. If No Answer----Calls from outdoor station without response in 30 seconds will
be transferred to the number set.
Even though the monitor will shut down when transfer via GSM is in progress, it
is still available to operate functions such as monitor, talk, and unlock.
3. Simultaneously----Calls from the outdoor station will be diverted to your
telephone immediately. In this mode the monitor won't shut off when GSM is
diverted successfully, if the monitor answersthe call at this point,GSM transfer
will terminate.
4. Set up Tel Number----Select this option to edit the divert number required.

5
Light
Main Menu
Restore
About
Setup
Light
Main Menu
Restore
About
Setup
Turn On
Light Option
Turn Off
Turn On 5min.
Ring Tune
User Setup
Monitor Time
Language Select
Ring Volume
Use / button to selete Light
item, then press Menu button
to confirm.
Use / Button to selete the item
you want, then press Menu button
to confirm.
Use /
item
button to select
Setup , then press Menu
button to confirm.
Use / Button to select the
option you want, then press Menu
button to confirm.
1. Ring Tone: Select it to set the ring tune of Door Station, Intercom and Door Bell.
2. Ring Volume: Select it to set the volume of monitor.
3. Monitor Time: Select it to set monitor time.
4. Language Select: Select it to set the language.
When the monitor is in standby mode, press Menu Button to enter main menu page.
Use / Button to move upward / downward to select 'Light' option, press Menu
Button to enter the 'Light' Option page, there are 3 options.
1.Turn On: Select it to open the staircase light, the light will be turned off
automatically after 60 seconds.
2.Turn On 5min:Select it to open the staircase light, the light will be turned off automatically
after 5min.
3.Turn Off: Select it to close the staircase light.
Note: the light function will be activated only when the system is connected to a light via
CDV-RLC module, otherwise, this function is disabled. For more information, please refer to
CDV-RLC user manual.
When the monitor is in standby mode, press Menu button to enter main menu page.
Use / button to move upward / downward to select Setup option, press Menu button
to enter the User Setup page, there are 4 options.
8. Light Function (Requires CDV-RLC)
9. Setup Function

6
Light
Main Menu
Restore
About
Setup
Light
Main Menu
Restore
About
Setup
Restore?
H/W : a1.1
About
Addr : 00.00
Video STD: AUTO
S/W : 00.01.00
[ 0000 ]
Installer Setup
When the monitor is in standby mode, press Menu button to enter main menu page.
Use / button to move upward / downward to select Restore option, press Menu button
to enter the restore page, then press Menu button to confirm.
Use /button to select
Restore option, then press
Menu button to confirm.
Press Menu button to confirm.
11. Monitor Parameter Setting
Use / button to select
About option, then press
Menu button to confirm.
Press Unlock button
and hold for 3secs.
Use / button to
increase/decrease the value
required, and press Menu
button to confirm.
11.1 How to enter the installation setting page
A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor
answers the call, conversation with the guard person is started..
The code number of 8004 is used to set the monitor as a guard unit monitor and 8005 is
used to cancel this function.
11.2 The setting items are as followings
11.3 How to set the monitor as a Guard Monitor
10. Restore to Default
[8000]:Master 0 [8001]~[8003]: Slave 1~3
[8004]:Guard unit [8005]:Not guard unit
[8006]:Video on slave when called [8007]:Video off on slave when called
[8014]:Unlock menu on (Lock 2) [8015]:Unlock menu off (Lock 2)

7
 
11.4 How to set the slave monitor address
11.5 How to set the monitor panel on

 cei 
Unlock mode:
Unlock time:
The unlock time can be changed at any time. It can be set from 1 to 9 seconds.Code
numbers from 8021 to 8029 are used to set the unlock time to 1~ 9 seconds.
There are two unlock modes: 1. Power-on- to-unlock type: unlock mode=0(by default)
2. Power-off-to-unlock type: unlock mode=1.
The code number of 8010 is used to set the unlock mode to 0
The code number of 8011 is used to set the unlock mode to 1
Maximum of 4 monitors can be connected in one apartment, one master monitor together
with 3 slave monitors, addresses must be the same.(note: must have one monitor to be
set as master monitor)
Code 8000 is used to set the master monitor.
Code 8001 is used to set the first slave monitor .
Code 8002 is used to set the second slave monitor .
Code 8003 is used to set the third slave monitor .
In default mode, when receive a call, the master and slave monitors will ring at the same
time, only the master monitor will display the image while the slave monitors do not. The
settings can be changed, the system can be set to allow the master monitor and all the
slave monitors to display video at the same time when receiving a call, input the code
number of 8006 on each slave monitor.
11.6 How to set the unlock parameter

8
Hold for 10s
•
•
Every apartment must have a unique identification called the User Code (address).
DIP switches are used to configure the User Code for each Monitor.
Bit-1 to Bit-5 are used to set the User Code. The values are from 1 to 32, giving 32 different
codes for 32 apartments.
•When multiple monitors(4 max) are installed in one apartment, these monitors have to use
the same User Code setting and the Master/Slave mode should be set on the Monitor.
Bit-6 is line termination switch (EOL), this has to be set to ON if the Monitor is at the end of
the line(bus), otherwise set to OFF.
11.8 User Code Setup
Flashes slowly (enabled)
11.7 How to enable/disable auto unlocking (Disabled by default).
Function Description:
Auto unlocking allows the door to unlock after 5 seconds of a placed call from the door
station without the need to answer or unlock the door, this allows the user to 'leave the
door on the latch' for a known visitor.
To Enable this function; from the installation page enter the following:
9018 is used to Enable the function - 'AU FUNC ON' will show on screen.
9017 is used to Disable the function - 'AU FUNC OFF' will show on screen.

9
ON(1)
ON ON
OFF(0)
Bit state User Code Bit state User Code Bit state User Code
Code=1 Code=12 Code=23
Code=2 Code=13 Code=24
Code=3 Code=14 Code=25
Code=4 Code=15 Code=26
Code=5 Code=16 Code=27
Code=6 Code=17 Code=28
Code=7 Code=18 Code=29
Code=8 Code=19 Code=30
Code=9 Code=20 Code=31
Code=10 Code=21 Code=32
Code=11 Code=22
Bit-6 line terminal setting:
Bit state Setting Bit state Setting
Monitor not at
the end of the
line.
Monitor at
the end of
the line.
1 2 3 4 5 6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP
1 2 3 4 5
6
ON DIP

10
Bright：5
13.Screen and Volume Adjustment
2.
sequence: Contrast,
Brightness Colour & Volume
Contrast, Brightness and Colour options are
for the image quality, adjust the value to
get the best image you like.
During monitoring or a call press Menu button, the Adjustment menu will be displayed.
Use the Menu to select the option required, use / button to increase/decrease the
value, press the Return button to quit the adjust page.
1. A total of 4 screen modes can be selected in ,
.
3. The Volume options are for ring tone and talking
volume adjustment.
door
station
BUS(IM) BUS(DS)
PC6
AC~
Doorbell Button
1 2
NC GND RING sw- sw+
3
ON
L1L2
DIP
4 5 6
12. Basic Connection
Switch

The design and specifications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved.
DT-ENG-43/D4-V1
14. Specications
●● Power●supply●for●indoor●monitor:●● ● DC●20~28V●
●● Power●consumption:● ●● Standby●0.17W;●Working●status●4.7W
●● Monitor●screen:● ● 4.3●inch●digital●color●TFT
●● Display●Resolutions:● ● 480(R,●G,●B)●x●272●pixels
●● Video●signal:● ● 1Vp-p,●75Ω,●CCIR●standard
●● Wiring:● ● 2●wires,●non-polarity
●● Monitor●time:● ● 40●seconds
●● Talking●time:● ● 90●seconds
●● Dimensions:● ● 137(H)×137(W)×17(D)mm