EB Excalibur Go! Cans XC6381 User manual

Go! Cans
Remote Control Vehicle
User Guide
#XC6381 - XC6382 - XC6383 © 2011 EB Excalibur, Inc.
XC6381IS01EXC
5 x 7 6/16/11
XC6381IS01EXC.indd 1 6/27/2011 5:35:32 PM

2
Congratulations on your new EXRC purchase! EXRC dragsters dominate the road with superior speed and control. Now that you’re an honorary EXRC dragster we recommend reading through
this manual thoroughly before attempting your rst race. Inside this manual you will nd driving
control tips, safety precautions and care instructions to keep your EXRC vehicle in tip-top shape. Follow
the instructions, and use your EXRC vehicle to feed your need for speed and race toward the checkered
ags! Ladies and gentlemen, start your engines!
Open the can, detach the can cover
and can body. Push the LOCK inside
the can cover towards the direction
shown to release the 4 ROADBLOCKS.
Take the transmitter and mini racer
out of the can body. Press the
RELEASE BUTTON down. Slide the
mini racer in the direction shown to
release it.
Slide the transmitter’s battery
compartment cover in the
direction shown and open it.
Insert 2 x AAA
or 1.5V LR03 batteries with
the correct polarity (+ and -), then
replace the battery cover.
Insert the CHARGING PLUG to the
CHARGING JACK on the bottom of
the mini racer. The INDICATOR lights
to show charging is in progress.
Insert
the antenna into the
antenna hole on the
transmitter and tighten.
XC6381IS01EXC.indd 2 6/27/2011 5:35:33 PM

3
INTERFERENCE
Some radio frequencies or other R/C units nearby can cause interference and
poor performance. Try to move away from the source of the interference.
The rechargeable battery is built
inside the racer. Plug the racer into
the correct side of the transmitter.
The charging plug is inside a hidden
door on the right side of the
controller.
Charge time is 1-2 minutes.
The racer is fully charged when
the CHARGING INDICATOR turns
o. The racer will run about 3-5
minutes on a full charge.
The CHARGING INDICATOR light will be
RED when the car is charging. The light
will turn o when fully charged.
1. Extend the transmitter’s antenna for better
signal reception. Turn the ON/OFF switch
on the mini racer to ON, and place it on the
ground.
2. Full Function Transmitter
• The signal indicator lights up when any button
on the transmitter is pressed.
• Press the LEFT/RIGHT button when the mini
racer is running forward or reverse to make it
turn left and right.
• The mini racer lights up its headlights when the
transmitter’s FORWARD button is pressed.
• The RELEASE BUTTON on the transmitter is
used to release the mini racer, which is locked
on the transmitter.
3. The DIRECTIONAL GUIDE is used to adjust the
mini racer’s direct-line running performance.
XC6381IS01EXC.indd 3 6/27/2011 5:35:33 PM

CARE & HANDLING
• Do not submerge in water or other liquids.
• Do not disassemble the product for any reason.
• Do not expose to extreme temperatures.
• Do not drop, throw, smash or otherwise cause physical shock.
• Clean using only a slightly damp cloth.
• Do not use cleaners with chemical agents.
• Do not short-circuit the battery terminals.
CAUTION – Battery Safety Information
• Non-rechargeable batteries are not to be recharged
• Rechargeable batteries must be removed before recharging
• Rechargeable batteries should only be recharged under adult supervision
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries
• Exhausted batteries are to be removed
• Do not mix old and new batteries
• Do not dispose of product in re; batteries may explode or leak
• If this product will not be used for an extended period of time, remove the batteries
from the product
• The supply terminals are not to be short-circuited
• Batteries are to be inserted with correct polarity
• Clean the battery contacts and also those of the product prior to battery installation
• As always, dispose of batteries in an eco-friendly manner
FCC Part 15 Compliance
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the product.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the transmitting equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio technician for help.
EB Excalibur, Inc.
Miami, Florida
www.EBExcalibur.com
[e-mail]
Distributed in the United Kingdom by:
EB Brands UK, Worcester WR4 9FA
XC6381IS01EXC
7mm
XC6381IS01EXC.indd 4 6/27/2011 5:35:33 PM