Echo ProThatch 99944200563 User manual

ProThatch Attachment
Operator's Manual
Model 99944200563
MODELS USED ON: SRM-2400SB
SRM-260SB/261SB
PAS-2400
PAS-2601
PAS-230/231
PAS-260/261
PAS-265/266
PAS-280
X7702093503 X770001303
10/12
WARNING
Users of this equipment risk injury to themselves and others if the unit is used im-
properly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to
do so could result in serious injury.

2
Copyright© 2012 By Echo, Incorporated
All Rights Reserved.
Table of ConTenTs
Introduction.................................................................... 2
- The Operator's Manual ........................................... 2
Safety ............................................................................. 3
- Manual Safety Symbols & Important Information. 3
- International Symbols............................................. 3
- Personal Condition and Safety Equipment ............. 4
- Equipment............................................................... 6
Description..................................................................... 7
Contents ......................................................................... 8
Assembly........................................................................ 8
- Fender/Wheel Assembly to
Lower Shaft Assembly............................................ 8
- Lower Drive Shaft Assembly to
Dethatcher Gear Housing ...................................... 8
- Front J-Handle Assembly ....................................... 9
- Power Head Shaft to Lower Shaft Assembly ....... 10
- Fender/Wheel Assembly Adjustment ................... 10
- Front J-Handle Adjustment....................................11
Operation...................................................................... 12
Maintenance................................................................. 13
- Skill Levels ........................................................... 13
- Maintenance Intervals........................................... 13
- Lubrication............................................................ 13
- Tine Replacement ................................................ 14
Storage ......................................................................... 16
Specications ............................................................... 16
Servicing Information .................................................. 20
- Parts/Serial Number.............................................. 20
- Service .................................................................. 20
- ECHO Customer Assistance ................................. 20
- Warranty Card....................................................... 20
- Additional or Replacement Manuals .................... 20
Specications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication,
but are subject to change without notice. Illustrations may
include optional equipment and accessories, and may not
include all standard equipment.
ProThatch Attachment
Operator's Manual
Model 99944200563
MODELS USED ON: SRM-260SB/261SB
PAS-2400
PAS 230/231
PAS 260/261
PAS-265
X7702093501 X770001301
01/09
WARNING
Read rules for safe operationand instructions carefully. ECHO provides an
Operator's Manual with your original Pro Attachment Series power source or Split
BoomTrimmer. That manual and this manual must be read and understood for proper
and safe operation. Failure to do so can result in serious injury.
InTroduCTIon
Welcome to the ECHO family. is ECHO product was designed and manufactured to provide long life and on-the-
job-dependability. Read and understand this manual. You will nd it easy to use and full of helpful operations tips and
SAFETY messages.
The operaTor'smanual
Keep it in a safe place for future reference. Contains specications and
information for safety, operation, maintenance, storage, and assembly
specic to this product.

ProThaTch aTTachmenT
oPeraTor'smanual 3
WARNING
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling, starting and stop-
ping instructions.
manual safeTy symbols and ImporTanT InformaTIon
Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre-
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
you.
safeTy
InTernaTIonal symbols
CAUTION
The safety alert symbol accompanied by the word
“CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal
injury if not avoided.
WARNING
The safety alert symbol accompanied by the word
“WARNING” calls attention to an act or condi-
tion which CAN lead to serious personal injury or
death if not avoided.
CIRCLE AND SLASH SYMBOL
This symbol means the specic action
shown is prohibited. Ignoring these prohi-
bitions can result in serious or fatal injury.
NOTE
This enclosed message provides tips for use, care and
maintenance of the unit.
IMPORTANT
The enclosed message provides information neces-
sary for the protection of the unit.
DANGER
The safety alert symbol accompanied by the word
“DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or
death if not avoided.
Keep bystanders at least 15
meters (50 feet) away.
AVOID KICKOUT
Beware Thrown Objects
Wear Eye Protection
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Read and under-
stand Operator's
Manual.
Wear eyes, ears
and head protec-
tion
Finger Severing
Safety/Alert
Plan retreat
path from falling
objects.
Wear slip resis-
tant foot wear.
Keep feet away
from blade
Thrown
objects
Wear hand and
foot protection
DO NOT USE
BLADES - Line
Head Only
Rotating
Cutting Attach-
ment
Do not operate closer
than 15 M (50 ft.) from
electrical hazards.
Keep bystanders
at least 15 meters
(50 feet) away.
Wear Face Shield
Keep bystanders and helpers
away 15 meters (50 feet) away.

4
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-
sations followed by loss of color and numbness in the ngers. The following precautions are strongly recommended
because the minimum exposure which might trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands and wrists.
• Maintain good blood circulation by performing vigorous arm exer-
cises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to ll each day with jobs where
operating the unit or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the ngers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE re-
quirements whenever you operate the trimmer.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the Trimmer/Brush Cutter handles. Gloves also
reduce the transmission of machine vibration to your
hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever
unit is used.
personal CondITIon and safeTy equIpmenT
Proper Clothing
Wear snug tting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY, or
clothing with loose or hanging items that could become
entangled in moving parts or surrounding growth..
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain
hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
are cooler.
WARNING
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are
not followed. Proper clothing and safety gear must be worn when operating unit.

ProThaTch aTTachmenT
oPeraTor'smanual 5
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator's Manual for
instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
ngers tightly encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on lad-
ders. Do not over reach.
Avoid Hot Surfaces
• During operation, the drive shaft housing, attachment bearing hous-
ing and mufer cover area may become very hot, too hot to touch.
Avoid contact during and immediately after operation.
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the ngers, hands, arms, and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position. Instead
try to maintain a straight wrist position. Also, when grasping, use your
whole hand, not just the thumb and index nger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force in which you do the repetitive movement.
• Do exercises to strengthen the hand and arm muscles.
• See a doctor if you feel tingling, numbness or pain in the ngers,
hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage can be prevented.

6
equIpmenT
WARNING
Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachment
combined with a non approved ECHO product.
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
• Inspect ProThatch tines for damage and that they are rmly secured in place. Replace tines if damaged or missing.
• Check that the dethatcher attachment is rmly attached and in safe operating condition.
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
NOTE
ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not
been tested and approved by ECHO.
desCrIpTIon
Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the
instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING
instructions for specic information.

ProThaTch aTTachmenT
oPeraTor'smanual 7
1. FLEXIBLE DRIVE CABLE - Cable end ts into drive shaft coupler of Pro Attachment Series or Split Boom mod-
els. Lubricate drive cable every 25 hours with high temperature automotive grease.
2. FENDER / WHEEL ASSEMBLY - Consists of pre-assembled wheels, wheel bracket, fender and rubber ap. For
best results, wheels should be adjusted for 13 mm (0.5 in.) ground clearance and are intended to provide operational
stability over uneven ground.
3. FENDER / RUBBER FLAP - Provides operator protection against thrown thatch, rocks and other debris. Always
insure that fender and ap are in place and in good condition before operating Pro Thatch Attachment.
4. LOWER DRIVE SHAFT ASSEMBLY - Included separately in the carton and must be assembled to the dethatcher
/ gear housing assembly. Contains exible drive cable, outer shaft housing and safety decal.
5. DETHATCHER / GEAR HOUSING ASSEMBLY - Right and left reels pre-assembled to gear housing.
6. DETHATCHER REELS - Dethatcher reels have 22 tines each and are pre-assembled to the gear housing. Reels
must be installed properly to prevent side pull.
7. GRASS GUIDE - Attached to the dethatcher assembly / gear housing. The guide prevents tines from penetrating to
deeply into the ground, which can cause the dethatcher to bounce and give uneven thatch removal.
8. TINES - Steel springs with 51 mm (2 in.) ngers. Tines are protected by a plastic cover to prevent thatch and dirt
buildup.
2
3
1
4
5
6
7
8
ConTenTs
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
___ 1 - Dethatcher / Gear Housing Assembly
___ 1 - Lower Drive Shaft Assembly
___ 1 - Fender / Wheel Assembly
___ 1 - J-Handle
___ 1 - Operators Manual
___ 1 - Warranty Registration Card
ProThatch Attachment
Operator's Manual
Model 99944200563
MODELS USED ON: SRM-260SB/261SB
PAS-2400
PAS230/231
PAS260/261
PAS-265
X7702093501 X770001301
01/09
WARNING
Readrules for safe operation and instructions carefully. ECHO provides an
Operator'sManual with your original Pro Attachment Series power source or Split
BoomTrimmer. Thatmanual and this manual must be read and understood for proper
andsafe operation. Failure to do so can result in serious injury.

8
assembly
AA
lower drIve shafT assembly To deThaTCher gear housIng
Parts Required: Dethatcher Gear Housing, Lower Drive Shaft with
Fender / Wheel Assembly
1. Place dethatcher gear housing on a at surface with gear housing
shaft mount at 45° angle.
2. Remove gear housing shaft alignment screw (A.
3. Loosen gear housing shaft mounting bolt (B).
A
B
95 mm
B
C
Parts Required: Lower Drive Shaft Assembly, Fender /
Wheel Assembly
1. Remove vinyl cap from lower end of drive shaft tube.
2. Loosen two (2) fender/wheel assembly bracket bolts (A). The bolts
should be very loose to prevent bracket from damaging locating
arrow decal label.
3. Install fender/wheel assembly, fender side rst, onto end of lower
drive shaft without serial number label. End of drive shaft should
be 95 mm (3.74 in.) from fender clamp. Assure locating hole (B) is
facing upward, and locating arrow decal (C) is aligned with edge of
fender clamp.
4. Tighten bolts (A).
fender / wheel assembly To lower drIve shafT assembly
WARNING
Do not perform maintenance or assembly procedures with engine running.

ProThaTch aTTachmenT
oPeraTor'smanual 9
A
B
C
D
4. Install and seat lower drive shaft end (end with fender/wheel as-
sembly into gear housing shaft mount. Make sure grass guide (D)
is facing down toward the ground.
5. Rotate and align hole in drive shaft housing with gear housing
shaft hole. Install and tighten alignment screw (A) .
6. Tighten gear housing shaft mounting bolt (B).
7. Check for proper inner ex cable (C) engagement into gear hous-
ing adaptor. If ex cable extends out of drive shaft then cable is
not properly engaged. Rotate and push cable end until lower cable
end slides into place in gear housing adaptor. Cable end will recess
approximately 16 mm (5/8 in.) into drive shaft.
fronT j-handle assembly
Parts Required: Pro Attachment Series or Split Boom Upper Shaft
and Power Head
1. Remove original front handle assembly. Assemble handle parts
with fasteners and store in a safe place for future application with
other attachments.
2. Remove two (2) J-Handle bracket bolts (A).
3. Install J-Handle assembly with handle grip on the left side (viewed
from the operator's position) onto the upper drive shaft. Lightly
snug bolts (A) to temporarily hold handle in place.
A
A

10
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
1. Set Power Head/Shaft Assembly on a level surface.
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to
lock-out position.
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
5. Carefully t attachment drive shaft assembly into coupler (B) to
decal assembly line (C), making sure that the inner lower drive
shaft engages into the square upper drive shaft socket.
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings t ush to decal point (E). New couplings are 4-3/4 in.
long, and t ush to line (C).
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap ush in coupler. Full engagement
will prevent further shaft rotation.
7. Secure lower shaft assembly to coupler by tightening clamping
knob (D).
fender/wheel assembly adjusTmenT
Dethatcher combing efciency is best when the full weight of the
dethatcher assembly rests on the tines during operation. Wheel height
should be adjusted for 6 - 13 mm (0.25 - 0.50 in.) above ground for
operational stability over uneven grass. Perform wheel height adjust-
ment procedures as follows:
1. Loosen (2) two lower hex head wheel bracket bolts (B).
2. Hold unit in comfortable operating position on a at surface and
check for wheel to ground clearance of 6 - 13 mm (0.25 - 0.50 in.).
3. Rotate wheels towards tines to reduce ground clearance; away
from tines to increase ground clearance. Tighten bolts (B).
power head shafT To lower shafT assembly
6 - 13 mm
(0.25-0.50 in.)
↔
B
D
C
A
A
B
D
E
C

ProThaTch aTTachmenT
oPeraTor'smanual 11
IMPORTANT
Do not rotate wheels against tines. Wheels and tines will be dam-
aged during operation.
If wheel rotation is not sufcient to provide proper wheel height clear-
ance then perform these additional steps:
4. Loosen two upper wheel bracket bolts (C).
5. Slide fender/wheel assembly up drive shaft housing until proper
wheel clearance is achieved. Tighten hex head bolts (C).
fronT j-handle adjusTmenT
Parts Required: None
1. Loosen two (2) J-Handle bracket bolts (A).
2. Rest dethatcher tines on at surface. Stand to left side of drive
shaft housing with right hand on throttle grip and left hand on
J-Handle.
3. Move J-Handle up or down drive shaft housing for comfortable
operating position. Tighten J-Handle bracket bolts (A).
C
A
A

12
Dethatching Information
Thatch is a normal buildup of grass and leaf clippings around the base of grass stems. Excessive thatch prevents air, wa-
ter and nutrients from reaching the root system, increasing the probability of lawn disease from mold spore and insects.
When excessive thatch is removed, air, water, nutrients and pesticides are allowed to keep your lawn healthy, promoting
denser, greener grass. In most areas some thatch approximately 6-13 mm (0.25 - 0.50 in.) is healthy for soil water reten-
tion. Never remove all thatch from your lawn. Contact your local government agriculture agency for best dethatching
practice for your lawn type and area.
Dethatching is recommended in early spring and late summer to allow grass to ll in low density areas of your lawn.
Dethatching should also be performed at regular intervals throughout spring and summer.
Dethatching is not recommended for grasses that have above ground root systems such as St. Augustine, Floratam, Pers-
ley, or Zoysia varieties. The dethatcher tines will damage delicate interconnected root systems of these grass varieties.
Dethatching Operation
operaTIon
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit.
1. Operate dethatcher in straight rows changing direction from row to
row as shown. If thatch is very dense a second dethatching opera-
tion may be required, and should be performed 90° to the original
pattern to assure best results.
2. Hold unit in a comfortable position engage throttle trigger to full
and allow dethatcher tines to "pull forward" over the ground. For
heavy thatch removal gently pull back against dethatching rotation,
to allow the tines to fully penetrate and remove thatch.
IMPORTANT
Do not remove grass guide attached to the gear housing to achieve
deeper tine engagement. The guide prevents tines from penetrat-
ing too deeply into the ground which can cause the dethatcher to
bounce during operation, and cause uneven thatch removal.

ProThaTch aTTachmenT
oPeraTor'smanual 13
lubrICaTIon
Level 1.
Parts Required: Lithium-based EP00 Grease for gearcase; POWER
BLENDXTM 8 oz. or Lithium Base Grease for
driveshaft
Gear Housing
1. Clean all loose debris from gear housing.
2. Remove screw plug (A) and check level of grease.
3. Add grease if necessary, DO NOT over ll.
4. Install screw plug (A).
A
maInTenanCe InTervals
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.
Wear gloves to protect hands from sharp edges and hot surfaces.
maInTenanCe
Your ECHO attachment is designed to provide many hours of trouble free service. Regular scheduled maintenance will
help your attachment achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to
take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR-
SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO
dealer for repairs.
skIll level
Level 1= Easy to do. Common tools may be required.
Level 2 = Moderate difculty. Some specialized tools may be required.
Component Maintenance Procedure Skill Level Interval
Drive Shaft Grease 1 Every 25 hours of use (1)
Gear Housing Grease 1 Every 25 hours of use (2)
Tines Inspect/Tighten/Replace 1 Before Each Use
Screws/Nuts/Bolts Inspect/Tighten/Replace 1 Before Each Use
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the frequen-
cy of required maintenance.
[1] Apply POWER BLENDXTM Grease.
[2] Apply Lithium-based EP00 Grease every 25 hours of use.

14
Drive Shaft (Lower)
1. Remove gear housing locator screw (A).
2. Loosen gear housing mounting bolt (B).
3. Pull gear box from drive shaft housing.
4. Pull exible cable from the drive shaft housing, wipe clean and
re-coat with a thin coating [15 ml (1/2 oz.)] of grease
5. Slide the exible cable back in the drive housing. DO NOT get
dirt on the ex cable.
6. Position lower drive shaft (end without safety decal) into gear
housing shaft mount.
7. Align hole in drive shaft housing with gear housing shaft hole
(C) and seat lower drive shaft end into gear housing shaft mount.
Install and tighten locator screw (A).
8. Tighten gear housing mounting bolt (B).
C
TIne replaCemenT
Level 2.
Parts Required: Thatching spring (P/N 61004725560), Screw (P/N
88995325560), plastic tube (P/N 21001325560)
Bent or broken tines should be replaced before operation for best det-
hatching efciency.
WARNING
Never replace tines with engine running. Tines are sharp, wear
gloves to protect your hands when replacing them.
A
B

ProThaTch aTTachmenT
oPeraTor'smanual 15
Tine Replacement
(Outer ve (5) rows from open reel end)
1. Hold inner tine mounting bolt from turning with 13 mm wrench
inserted through open reel end.
2. Grip plastic sleeve at the base of the tine rmly with vice grip. Re-
move tine from bolt turning tine counter clockwise. Remove bolt.
3. Insert new bolt with star washer through reel mounting hole.
IMPORTANT
Star washer must be assembled on tine mounting bolt, otherwise
bolt and tine will loosen on the reel.
4. Install tine onto bolt turning tine clockwise with vice grip. Tighten
securely.
Tine Replacement
(Inside tine nearest gear housing)
5. Disconnect dethatcher attachment from Power Head/Shaft.
6. Rotate ex cable (C) mounted in the dethatcher assembly drive
shaft housing. Turn ex cable end until front dethatcher gear hous-
ing to reel end clearance is achieved for tine bolt head access with
13 mm wrench. (See photo at right.)
7. Replace tines following steps 1 - 4 above.
8. Connect dethatcher attachment to Power Head/Shaft.
C

16
sTorage
1. Clean dethatcher attachment with a bristle brush and rinse with
clear water.
IMPORTANT
Do not immerse this attachment in water. Water will enter gear
housing and damage gears, bearings and seals.
2. Apply thin coating of oil to metal parts to prevent rust.
3. Lubricate lower shaft assembly with grease.
4. Store ProThatch Attachment in a dry place out of reach of children
with lower shaft housing in a horizontal or vertical postion to pre-
vent grease loss from open shaft end.
speCIfICaTIons
MODEL ---------------------------------------------------- PRO THATCH ATTACHMENT
Shaft Length ------------------------------------------------ 928 mm (36.5 in.)
Attachment Width ----------------------------------------- 565 mm (22.2 in.)
Attachment Height----------------------------------------- 403 mm (15.9 in.)
Weight ------------------------------------------------------- 9.6 kg. (21.14 lb.)
Drive Shaft-------------------------------------------------- 6.35 mm (0.25 in.)
Rotating Direction ----------------------------------------- Away from the operator viewed from the rear
Dethatcher Head ------------------------------------------- Left and right reels mounting 22 tines each, totaling 44 tines
Tines --------------------------------------------------------- 3mm (.19 in.) spring steel
Combing Width -------------------------------------------- 571 mm (22.5 in.)
Lubrication-------------------------------------------------- Lithium Base Grease
Gear Reduction Ratio ------------------------------------- 42.75 : 1
Dethatcher Operating (RPM)----------------------------- 210
Engine Wide Open Throttle (RPM) w/attachment ---- 7,700 - 8,500

ProThaTch aTTachmenT
oPeraTor'smanual 17
noTes

18
noTes

ProThaTch aTTachmenT
oPeraTor'smanual 19
noTes

ECHO, INCORPORATED
400 oakwood road
lake ZurICh, Il 60047-1564
www.eCho-usa.Com
servICIng InformaTIon
parTs/serIal number
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assem-
blies for your ECHO products are available only from an Authorized
ECHO Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the attachment with you. You can nd
these numbers on the driveshaft model/serial number label. For future
reference, write them in the space provided below.
Model No. _____________ SN. ____________
servICe
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on
our Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
eCho Consumer produCT supporT
If you require assistance or have questions concerning the applica-
tion, operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30
am to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
warranTy regIsTraTIon
You may register your Echo equipment using the warranty registration
card or register on-line at www.echo-usa.com. Registering provides a
direct link between you and ECHO if we nd it necessary to contact
you.
DEALER?
Call
1-800-432-ECHO
or
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
S08300001001/S08300999999
addITIonal or replaCemenT manuals
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558).
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.