ecoStage B480 User manual

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
1
470W BEAM SPOT WASH(CMY)
WEIGHT：24.5 KG
POWER：600W
BEAM+SPOT+WASH

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
2
ITEM
Item..............................................................................................................................02
1.Production introduce..............................................................................................02
2.Fixture size...............................................................................................................03
3.Parts introduce....................................................................................................... 04
4. Color and gobo description...................................................................................05
5.Safety information...................................................................................................06
6.Packing and shipping .............................................................................................07
7.Installation standard...............................................................................................08
8.AC power................................................................................................................ 09
9.Lamp model and replace....................................................................................... 09
10.Control panel ........................................................................................................11
11.Control panel menu perate.......................................................................11
12.DMX Channels......................................................................................................16
13.Routine maintenance............................................................................................22
14.Simple troubleshooting.........................................................................................22
STATEMENT
The product is good packing when ship out the factory. All users should strictly abide by the
warnings and instructions stated in this manual, any damage and results due to misuse and the
neglect of this operating manual will be excluded from the deal responsibility this manual will not
informed in additionally if have technical changes.
PRODUCTION INTRODUCE
Thank you for choosing this product. This is our latest development of intelligent, efficient
products, beautiful and fluent, combined with the advanced technology of the stage lighting today.
It has advanced international electronic control technology and excellent human nature chemical
industry. The product is fully in conformity with the CE standard and the recipient country. The

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
3
standard DMX512 signal mode is supported by the RDM protocol.
Production enforce standard IEC 60598-1:2014，IEC60598-2-17:2017.
Channels mode : 34/39CH;
Lamp: OSRAM SIRIUS HRI 470W XL;
Power: 110-240V,50/60Hz;
Total power: 600W;
Display: 2.8 inch screen display, can reverse 180°;
Color Wheel: 11 Colors+2700k +3200k+white+CMY
Color glass: imported Italian ODL color chip, special high temperature resistant raw material,
and bright color.
Color Mixing System!
Fixed gobo : 14 gobo + white.
Rotation gobo: 9 gobo+ white,changeable;
Animation Gobo:could Used By Separately Or combined With Gobos
Rotation Prism Wheel 1:8 Facet Prism+linear 6
Facet Prism+cylindrical Prism
Rotation Prism Wheel 2:8 Facet Prism+linear 6
Facet Prism+double Layer Prism
Prism Wheel 1 And Prism Wheel 2 Can Overlay
Frost:separately Frost
Beam angel : 2.5～45°;
USB connector can set dmx address with power and upgrade the software. (RDM function)
Dimmer : 0-100% l inear adjustment ;
Pan : 540°; 8Bit/16Bit; / Ti lt : 270°; 8Bit/16Bit ;
IP Rate: IP20;
Product size: 405x245x685 mm;
Flycaes: 930x520x910 mm / Carton box: 540x450x650 mm;/N.W: 24.5 KG / G.W: 28
KG(carton).
1. FIXTURE SIZE
Size：405（L）×245（W）× 685（H）mm

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
4
2. PARTS INTRODUCE
470W HYBRID WITH CMY each part of product structure and main composition product name
description for better know the light unit.
470W HYBRID WITH CMY Control panel function introduction, mark for the part name
on the panel, familiar with the function of every part.

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
5
4. COLOR AND GOBO DESCRIPTION
4.1 Color wheel with 11 colors (2700K+3200K)+white+CMY,pure colors,perfect effect;
4.2 Static gobo wheel with 14gobos +white,rich gobos;
4.3 Rotate gobo wheel with 9gobos+white,smooth gobo rotation,replace easily;
Two rotation prism, one 8 facet prism, one linear 4 prism, one fixed 16 prism,each two prism
can combined using together. Frost function.

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
6
5. SAFETY INFORMATION
5.1.1 Safety warning message.
1.This product is only suitable for professional use, and does not apply to security for other
purposes.After you got the lights, please check the package whether have any damage caused by
transportation. If there is any damage, do not use this fixture, and please contact the dealer or
manufacturer as soon as possible.
3. This product is only suitable for indoor, IP20 protection class. Lamps should be kept dry to
avoid Moisture, overheating or dusty environment. Prevent lamps come into contact with water or
any other liquid.The use of this product should pay attention to: fire, heat, electric shock,
ultraviolet radiation, the lamp to explode and so on .
Shedding caused serious or fatal injury. Need to read the instructions before use energized or
installing. Follow through the operation of security methods and pay attention to the warning signs
on the specification and equipment. If you have any problem for how to safely operate the
equipment. Please contact your dealer.
5.1.2 ANTI-HIGH TEMPERATURE
ta=40°C
Please don’t use the equipment if the temperature above 40℃
5.1.3 BURST PREVENTION
The lens should be changed if had damaged or any problems. Don’t change the non-original
manufacturer lens.
Len size：Φ158×43 mm
5.2 TO PREVENT FALLING WOUNDING
Please don’t move the package by one person only.
When Hang the fixture, please must verify that the facilities to be able to withstand the
weight of the lamps at least 10 times more.
Please make sure the Mounting hardware is strong enough no any damage, and insurance for
the safety rope as auxiliary security fixed in other facilities will need to verify before
installation. Installing or removing the equipment, to make the pulley below the work
location.
5.3 UA PROTECTION AND THE BULB EXPLOSION
Prohibit straight viewpoint with exposed bulbs to avoid UV damage to the eyes;
Do not use the equipment without the lens screen and the lid;
The lens and the light head covers should be timely replaced if any damage to rupture
The Fixture should be used with the protection screen together.

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
7
5.4.1 PREVENTION OF ELECTIC SHOCK
The electrical connection must only be carried out with corresponding qualifications;
Before installing, make sure you use the power voltage lamps must comply with the
identified power, voltage and have an overload or leakage protection;
Each lamp must be properly grounded, installed in accordance with the relevant standards;
Cut off the power when stall or replace the lamp and the fuse;
Prohibit the use of a lightning storm or wet environment.
5.4.2 TO PREVENT BURNING OR FIRE
1. The fixture can be mounted directly on the surface of ordinary combustible
material.
2. Do not short-circuit temperature protection switch or fuse, use the specified type of fuse.
3. The equipment must be installed away from inflammable and explosive materials.
4. The equipment should be projected range of 15 meters away objects and projectiles
temperature less than 60 ° C 15m
5. Fan or ventilation, at least in the range of 0.5 meters can not be an obstacle.
6. Do not place any object on the lens.
7. Handling at least allow the device to cool for 20 minutes.
8. Do not replace the non-original parts.
6. PACKINGAND SHIPPING
Packed with fly-case of two in one ,or carton box. Attach follow accessory.
6.1ACCESSORY
CONTENT
QUANTITY
USER MANUAL
1
HANG FIXTURE
1
SIGNAL CABLE
1
6.2 TRANSPORT PROTECT LOCK
In order to protect the light, there is a protect lock; During the transport , the lock catch
position need lock in the center, and the fixture keep in vertical state.
6.3 ABOUT PACKING
1. Before packed, make sure power is off, and wait for at least 20mins for cooling down.
2. Before clean the fixture, make sure X, Y axis protect lock closed.
3. After packed by plastic bag, high-lift the fixture with two handles besides the product. put

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
8
the product into the fly-case up-side-down.
4. After packed the product, put the accessory into the accessory case, then closed and lock the
fly-case.
5. Fly-case only up stacked two layers. Prohibited upside down
6. When packed with carton box, equipment should be put into the foam first, then set into a
carton, pay attention to the vertical position.
6.4 UNPACKING
Note: Before unpacking check the damage is whether due to the transportation or not, if you
find any such damage, please do not use this item, and contact with the dealer or
manufacturer as soon as possible.
1. Open the fly-case, and discover the inside plastic bag.
2. High-lift the product by two handles beside the bottom base and move it out.
3. Before power on, make sure you have opened the X, Y axis lock!
7. INSTALLATION STANDARD
7.1 INSTALLATION RIGGING
The product can be placed on the stage or installed on the bracket in any direction. The
quick lock system can quickly and easily press 2 directions to lock on the bracket.
7.2 DEVICE FIXED
1.Before installation, it must be verified that the rigging equipment clamp is not damaged and can
bear at least 10 times of the weight of the equipment, and that the building can bear at least 10
times of the total weight of the equipment and the fixture fuse accessory equipment;
2.The fixture is installed on the base of the lamp body, the fastener is inserted horizontally into the
mounting hole of the base, the handle of the fastener is grasped and rotated clockwise for 1 / 4 turn
to lock, and other fasteners are installed in the same way.
3.Verify whether the horizontal and vertical locks have been opened, and verify that there are no
inflammables or other nearby inflammables within 3 meters of the device.
7.3 Device connection
Attention!
Must use two clamps fix the fixture,and tighten the clamps with1/4 lock, only fully
clockwise rotate 90 °then can lock the fasteners. Add one safety insurance rope on the hole of
light base. pls attention not connect to the transport handle.
Attention! One product only can accept one input one output.DMX512 cable must use the
professional shielded twisted pair cable; standard loudspeaker cable is not reliable to control the
long-range data. 24AWG cable is suitable for more than 300 meters long-distance signal

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
9
transmission and must add\ DMX 512 signal amplifier.
Do not use two outputs to separate the connection, if separate a continuous connection to branch,
DMX512 splitter is necessary.
If use the DMX512 splitter. At first connect DMX512 Splitter input terminal to controller .And
then connected from the splitter output terminal to next device.
Do as above guide to connect other device, and finally coupled with terminal insertion
8. AC POWER
8.1 VOLTAGE, POWER, FUSE SPECIFICATION
Input Voltage
Total Power
Frequency
110-240V
600W
50/60HZ
Fuse voltage
Electronic current
Specification
250V
10A
5×20
8.2 Power connection attention:
Attention!
The device must be operated by professionals; Make sure that the voltage of power supply must be
comply with the voltage identified on the lamp, and must have an overload or leakage electrical
protection.
Live wire(L)
Null(N)
Ground wire
RED
BLUE
Yellow +Green
9. LAMPMODELAND REPLACE
470W HYBRID WITH CMY LAMP
LAMP MODEL
POWER
LIFE/HOUR
LUMEN
OSRAM SIRIUS HRI 470W
XL
470w
1500 HOURS
114900Lux
WARNING! There is a safety hazard or damage if install similar bulb To reduce
the risk of damage to light ,do change the lamp before using time over 125% of
lamp life .
LAMP REPLACE
Attention! When replace the lamp is forbidden to touch lamp with bare hand, to avoid the greasy
dirt stains filament. filament must be kept clean. Disconnect the power. Before replace lamp,
fixture need 20 minutes for lamp cooling. Fasten the head with Y axis protect lock in 60 °
position.

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
10
1. Use cross screwdriver to open the light body cover(picture 1)
（1）
2. After open the cover,you can see the lamp inside,please wait the lamp be cool after used but not
touch it in hot status.(picture 2)
（2）
3. One hand press the lamp holder,another hand hold the lamp,and pull out the wires(picture 3,4)
（3）（4）
4.after take apart the lamp, please check the inside glasses, clear it will make the light better
effect.(Picture 5)
（5）
5.install the lamp after replaced.

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
11
10. CONTROL PANEL
The control panel has a user friendly touch screen to display the operation data and other
information.
There are four buttons on the right side.
Each button has a dedicate function.
Top button is for upward movement , lower button is for downward movement. The left button is
for exiting the selected function where the right button in for confirming the function or data.
11. CONTROLPANEL MENU OPERATE
Main Menu
Submenu 1
Submenu2
Function SET
Function description
DMX ADDRESS
<<
1-512
to address 1
<
address up
>
address down
<<
to address 512
NEXT
Address up channels in this mode
SAVE
save and back
ESC
back
FEATURES
SETTING
Wire Output:
Open
WDMX output on
(custom function)）
Close
WDMX output off (custom
function)
Wire Set:
Hold
WDMXSet up maintain
(custom function)
Clear
WDMX Set up delete
(custom function)
Channel
34CH
34CH mode
Button
TOUCH
SCREEN
DISPLAY

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
12
Mode:
39CH
39CH mode
Pan Reverse:
Off
Pan Scan Normal
On
Pan Scan Reverse
Tilt Reverse:
Off
Tilt Scan Normal
On
Tilt Scan Reverse
Opto Check:
Off
Pan/Tilt optical sensor testing off
On
Pan/Tilt optical sensor testing on
PT Speed:
Noml
Pan/Tilt Scan Speed setting
nomal
Slow
Pan/Tilt Scan Speed setting
slow
Fast
Pan/Tilt Scan Speed setting
fast
Singl Clear:
Off
keep signal data
On
clear signal data
ECO MODE:
Off
Energy saving mode off
On
Energy saving mode open
ADV.
(ADVANCED FUNCTION)
RST.
Re-setting and back
SAVE
Save and back
ESC
Back
ADVANCED
FUNCTION
Redress
ZEROSETTING
Pan:
0-255
Adjust the begging state
Tilt:
Focus:
Zoom:
Cyan:
Magenta:
Yellow:
Colour:
Static Gobo:
Rot Gobo:
GoboRot:
XGobo:
Dimmer:
Prism:
Prism Rot:
Prism2:
Prism2 Rot:
Frost:
Softern:
SAVE
Save and back
>
Value+1

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
13
<
Value-1
ESC
Back
ChanlDef
No function
FactSett
Only factory only
UseManage
Limit
LimitTime
No function
limitCont
No function
DefConfig
YES
Return to default
NO
back
FacConfig
SAVE
Save and back
EPRT
for factory only
ESC
back
ESC
back
UNLOCK
Verify1:
0-255
need password
Verify2:
KEY
need password
ESC
back
MANUAL
LAMP
REST
ALL
MOTER
All step motor(do not adjust it )
XY
MOTER
Pan/Tilt step motor adjust(do not
adjust it )
PART
MOTER
Local motor
YES
The chosen step motor reset
ESC
Back
TEST RUN
AUTO
Auto
SOUND
Sound
ESC
Back
SMULATE
DMX
Pan:
0-255
Control Channel on display
Pan Fine:
Tilt:
Tilt Fine:
PT Speed:
Special Fun:
Cyan:
Magenta:
Yellow:
Colour:
Colour Fine:
Virtual Color
Effect
Speed:
CMY Speed:
Beam Speed:

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
14
Effect_W:
Effect_R:
Effect_A:
Static Gobo:
Rot Gobo:
Gobo Rot:
GRot Fine:
Prism1:
Prism1 Rot:
Prism2:
Prism2 Rot:
Pattern_S:
Pattern_R:
Beam_S:
Beam_R:
Frost:
Zoom:
Zoom Fine
Focus:
Focus Fine:
Aoto Focus:
Strobe:
Dimmer:
Dimmer
Fine:
>
Value+1
<
Value-1
ESC
Back
ESC
Back
SYSTEM INFO
DMX
VALUE
CH00-CH39
0-255
DMX value number
REST INFO
Pan:
Right/Erro
Motor reset status
Tilt:
Focus:
Zoom:
Colour:
Static Gobo:
Rot Gobo:
Gobo Rot:
Prism:
Prism Rot:
Beam:
Beam Rot:

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
15
ESC
Back
OTHER
INFO
LightType:
470W
HYBRID
WITH CMY
Device model
Run Time:
0-99999
Machine runing hours
Run Count:
0-99999
Machine runing times
Fan 1:
0-9999
Fan 1 speed
Fan 2:
0-9999
Fan 2 speed
Temp:
xxx
Deceive temperature
DisVersion:
Vxxx
Version of display software
XY Version:
Vxxx
Version of Pan/Tilt software
M1 Version:
Vxxx
Software Version M1
M2 Version:
Vxxx
Software Version M2
ESC
Back
ESC
Back
DISPLAY
SETTING
Light Set:
1-7Lev
Back Ground light level
Light Off:
On
Keep back ground light on
1Min
Back light turn off after 1 min
2Min
Back light turn off after 2 mins
3Min
Back light turn off after 3 mins
Menu Back:
Off
Turn off the menu and back
1Min
Menu back after 1 min
2Min
Menu back after 2 mins
3Min
Menu back after 3 mins
Light Flash:
Off
Back ground light flash function
off
On
Back ground light flash function
on
Touch Cali:
Off
Touch screen calibration off
On
Touch screen calibration on
SAVE
Save and back
ESC
Back
LAMP SETTING
DeviceID
0-FFFFFFFF
RDM address
LampTime
0000-9999
Lamp time
Manual
Lamp:
Off
Lamp off by manual
On
lamp on by manual
LampState
Off
Lamp off
On
Lamp on
Lamp Off:
10M
After 10 mins no signal come in,

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
16
Lamp off
Off
No signal come in , lamp keep
lighting
Lamp
Default:
Off
Lamp off
On
Lamp on
Angle Cail:
Off
Turn off lamp angle calibration
On
Turn on lamp angle calibration
12.DMX Channels
XMLIET 470W HYBRID WITH CMY
Channels
34 CH
39 CH
Function
DMX
DMX
1
1
Pan rotate
0-255
0~540°
2
2
Pan fine
0-255
Pan Fine
3
3
Tilt rotate
0-255
0~235°
4
4
Tilt fine
0-255
Tilt fine
5
5
P/T Speed
0-255
P/T Speed from far to slow
6
6
Function
description
0-39
一
40-44
ECO Model (380W)
45-49
Standard moded (470W)
50-129
一
130-139
Lamp on
140-149
PT Reset
150-159
一
160-169
Small Step Motor Reset
170-199
一
200-209
All the small step motor Reset
210-229
一
230-239
Lamp Off
240-255
一
7
7
Cyan
0-255
light cyan
8
8
Magenta
0-255
light magenta
9
9
Yellow
0-255
light yellow
0
White
1-127
Color gradation
128-129
WHite
130-134
GOBO 1
135-138
GOBO 2
139-143
GOBO 3
144-147
GOBO 4
148-152
GOBO 5

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
17
10
10
Color wheel
153-157
GOBO 6
158-161
GOBO 7
162-166
GOBO 8
167-171
GOBO 9
172-176
GOBO 10
177-180
GOBO 11
181-185
GOBO 12
186-189
GOBO 13
190-215
Clockwise flow from fast to slo
216-217
Stop
218-243
Anti - clockwise flow from slow to fa
244-249
Sound control color
250-255
Radom color
*
11
Color wheel fine
0-255
一
0
一
11
12
Color macro
1-2
Macro 1
3-4
Macro 2
…
…
129-130
Macro 65
131-132
Macro 66
133-255
一
12
13
CMY Speed
0-255
一
13
14
Color macro speed
0-255
一
14
15
Beam speed
0-255
一
15
16
Effect wheel
0－19
一
20-127
lndex (open-full)
128-170
Strobe (open-full) fast to slow.
171-213
Strobe (open-half) fast to slow.
314-255
Strobe (half-full) fast to slow.
16
17
Effect wheel
rotation
0
Stop
1-127
Clockwise flow from fast to slow.
128
Stop
129-255
Anti - clockwise flow from slow to fast.
17
18
Effect macro
0-255
一
0-3
Hole
4-9
GOBO 1
10-15
GOBO 2
16-21
GOBO 3
22-27
GOBO 4
28-33
GOBO 5
34-39
GOBO 6
40-45
GOBO 7
46-51
GOBO 8

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
18
18
19
Fixed GOBO
52-57
GOBO 9
58-63
GOBO 10
64-69
GOBO 11
70-75
Slim Beam 1
76-81
Slim Beam 2
82-87
Slim Beam 3
88-95
GOBO 1 shake
96-103
GOBO 2 shake
104-111
GOBO 3 shake
112-119
GOBO 4 shake
120-127
GOBO 5 shake
128-135
GOBO 6 shake
136-143
GOBO 7 shake
144-151
GOBO 8 shake
152-159
GOBO 9 shake
160-167
GOBO 10 shake
168-175
GOBO 11 shake
176-183
Slim Beam 1 shake
184-191
Slim Beam 2 shake
192-199
Slim Beam 3 shake
200-201
Hole
202-222
Clockwise flow from fast to slow.
223-243
Anti - clockwise flow from slow to fa
244-249
Sound control GOBO
250-255
Random GOBO
0
一
1－4
Maximal hole
GOBO positioning（GOBO rotation index mode)
5－7
GOBO 1
8－10
GOBO 2
11－13
GOBO 3
14－16
GOBO 4
17－19
GOBO 5
20－22
GOBO 6
23－25
GOBO 7
26－28
GOBO 8
29－31
GOBO 9
GOBO positioning (GOBO rotation mode)
32－34
GOBO 1
35－37
GOBO 2
38－40
GOBO 3
41－43
GOBO 4
44－46
GOBO 5
47－49
GOBO 6

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
19
19
20
Rotation GOBO
50－52
GOBO 7
53－55
GOBO 8
56－59
GOBO 9
GOBO shake form slow to fast
（GOBO rotation index mode）
60－67
GOBO 1 shake
68－75
GOBO 2 shake
76－83
GOBO 3 shake
84－91
GOBO 4 shake
92－99
GOBO 5 shake
100－107
GOBO 6 shake
108－115
GOBO 7 shake
116－123
GOBO 8 shake
124－129
GOBO 9 shake
GOBO shake from slow to fast ( GOBO rotation mode.
130－137
GOBO 1 shake
138－145
GOBO 2 shake
146－153
GOBO 3 shake
154－161
GOBO 4 shake
162－169
GOBO 5 shake
170－177
GOBO 6 shake
178－185
GOBO 7 shake
186－193
GOBO 8 shake
194－199
GOBO 9 shake
200－201
Maximal hole
202－222
Clockwise flow from fast to slow.
223－243
Anti - clockwise flow from slow to fast.
244－249
Sound control GOBO
250－255
Random GOBO
20
21
Rotation GOBO
GOBO rotation index mode.
0-255
Index
GOBO rotation index mode.
0
Stop
1－127
Anti - clockwise flow from slow to fast
128
Stop
129－255
Clockwise flow from fast to slow.
*
22
Rotation GOBO fine
0－255
一
21
23
Prism whee1
0-3
一
Index mode
4-7
Prism 1
8-11
Prism 2
12-15
Prism 3
Rotation mode
16-19
Prism 1

מ"עב םינפלואו ןורטאת תוכרעמ רואנד7444222 |-| [e-mail]|www.danor.com| רגנה 'חר9ןורשה דוה ,
20
20-23
Prism 2
24-255
Prism 3
22
24
Prism 1
Rotation
Index mode
0-255
Index
Rotation mode
0
Stop
1－127
Clockwise flow from fast to slo
128
Stop
129－255
Anti - clockwise flow from slow to fa
23
25
Prism whee1 2
0-3
一
Index mode
4-7
Prism 1
8-11
Prism 2
12-15
Prism 3
Rotation mode
16-19
Prism 1
20-23
Prism 2
24-255
Prism 3
24
26
Prism 2
Rotation
Index mode
0-255
Index
Rotation mode
0
Stop
1－127
Clockwise flow from fast to slo
128
Stop
129－255
Anti - clockwise flow from slow to fa
25
27
Prism macro 1
0-3
一
Index mode
4-5
Macro 1
6-7
Macro 2
…
…
24-25
Macro 11
26-27
Macro 12
Rotation mode
28-29
Macro 1
30-31
Macro 2
…
…
64-65
Macro 19
66-67
Macro 20
68-255
一
26
28
Prism macro 1
Rotation
Index mode
0-255
Index
Rotation mode
0
Stop
1－127
Clockwise flow from fast to slo
128
Stop