Larson Electronics Golight 51494 Manual

51494 Golight Wired Remote Control
LED Spotlight - 900' Beam - 36 Watt High
Power LED - Perm. Mount
INSTRUCTION GUIDE
Part# GL-9149
Congratulations
You are now the owner of one of the finest remote control searchlights available today. Thank you for
letting Larson Electronics assist you in your lighting application needs. We're proud of our products and
the technology that we've developed to ensure our customers the most durable, versatile and powerful
searchlights in the lighting industry.
Please read these instructions before using your new Remote Control Spotlight from Larson Electronics.

The Golight® is a Portable Searchlight designed to
be permanently or temporarily attached to a vehicle
for your specific use. The Searchlight with
Directional Flexibility is controlled by a wired remote,
which gives the operator a full 370° horizontal
rotation and a 135° vertical tilt with fingertip control.
The Golight® provides superior light penetration with
Cr5 PentaBeam™ technology in a halogen
configuration or with state of the art P-Vex™ lens
and LED technology.
MOUNTING INSTRUCTIONS
Temporary (Suction):
1. Always clean mounting surface with a clean
cloth.
2. Remove light from permanent mount shoe by
depressing spring-loaded lock and sliding
light out.
3. Place suction base on clean, dry surface and
move side lever into the locked position.
WARNING: Check the suction cup frequently to
ensure that suction strength is maintained.
Temperature variations, rough terrain, grease
and dirt affect the length of time that the suction
cup will remain in place. Suction mounting is not
recommended for road use.
Permanent:
1. On clean, dry surface, place gasket and
shoe in desired location. Using 3/16” screws,
attach shoe to vehicle.
2. Slip the Golight® into the shoe. Verify that
the spring lock secures the Golight® into the
shoe. An optional magnetic mounting shoe
is available (see web store).
OPERATION OF GOLIGHT®
1. Place your Golight® into the mounting shoe
or attach to the outside of your vehicle (see
mounting instructions).
2. Plug your Golight® into your vehicle’s
cigarette lighter outlet or12 Volt direct battery
hookup.
3. Using the remote control, turn on the light by
depressing the on/off button.
4. With the 4-way arrows on the remote
control, rotate your light to the desired
location.
5. The spotlight should not be turned on when
the snap on lens cover (rockguard) is
attached. (Not applicable for LED)
USAGE:
» This light is intended for off-road and utility use only
» This light is intended to be mounted outside the
vehicle while in use
» This light may only be disassembled and repaired
by an authorized representative
MISUSE:
» This light is not approved for road or highway use
» This light is not approved for underwater use
» This light is not approved for inverted mounting
» This light is not approved for use inside a vehicle
or enclosure and power should be disconnected prior
to placing the light in such circumstance
» This light may be damaged if operated in icing
conditions
» This light may only be dismantled by an authorized
Golight representative.
» Any violation of the above referenced misuses
will be considered grounds for warranty refusal.
IMPORTANT SAFETY INFORMATION
This symbol is to alert you to important operating
or servicing instructions that appear in your
instructions. Always follow basic safety precautions
when using this product to reduce the risk of injury,
fire or electric shock.
This light is for off road and utility use only. It is
not designed for road use as a driving light.
FCC RULE Part. 15.21 - Changes or
modifications made by the user not expressly
approved by Golight, Inc. for compliance could void
the user’s authority to operate the equipment.
For safe and efficient operation of your Golight®,
observe these guidelines:
Using your Golight® in icing conditions could
damage the gear motors.
The remote must be kept clean and dry to avoid
damage to the internal circuitry.