Ecotec Fountain 5/160-LED User manual

Operating manual
solar waterpump system
“Fountain 5/160-LED”
These instructions relate ONLY to this product and contain important infor-
mation for using the product for the first time. Please keep these instructions
for later reference and should always accompany the product in the event of
transference to a new user.
1. Introduction
Dear Costumer,
Thank you for purchasing the solar light. With this solar light you purchased a product
manufactured according to the current state of technology.
This product fulfils all requirements of the valid European and national regula-
tions. The conformity was proved. The relevant declarations and documentati-
on are deposited with the manufacturer.
To maintain this state and guarantee a safe operation, you as the user will have to
follow this operating manual!
2. Safety Instructions
- In case of damages caused by not
following this operating manual, the
warranty rights will expire! We exclude
liability for any consequential damages!
- We exclude liability for property or
personal damages caused by inappropriate
handling or not following the safety instructions.
- In these cases any guarantee rights will expire.
Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct
and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade cooperative
association for electric plants and working material are to be considered in industrial
environments.
3. Intended Use
- The pump system is designed for the outdoor use in garden ponds. The
integrated accumulator is charged depending on the solar radiation to the
solar module and the pump will produce water correspondingly.
- A direct and shadow-free solar radiation is required for the function of the
pump.
- When starting the pump, the integrated accumulator may be partially
discharged and the pump will not produce/lift any water. Please charge the
accumulator in the accumulator station for one day with solar radiation and
leave the pump switched-off while charging (switch in position “OFF”). For
more details, please see the manual of the accumulator box.
- The pump system is particularly characterized by its ease of installation and
assembly. No tools are required for the assembly.
- The pump must not be used for the production/lifting of drinking water.
- In order to avoid any disturbing gurgling, simply shorten the standpipe.
- In order to safely interrupt the production (of water) and protect the system
against unauthorized activation, you will have to switch-off the pump system
and disconnect the cable between accumulator box and pump.
4. Assembly and commissioning
The pump system consists of the following components:
1. 5 Wp solar module with ground spike.
2. Submerged pump in a plastic housing with a 5 m connection cable.
3. Accumulator box with a 6,4 V/ 1,5 Ah Li-Fe accumulator.
4. Standpipes and 4 water nozzles.
5. LED Light ring with twilight sensor mounted on an adapter.
Note: Before assembly, please carefully read the manual of the accumu-
lator box. It contains important information and notes!
1. Completely unroll the connection cable at the pump.
2. Attach the adapter to the pump outlet and then the standpipes onto the
adapter. Then, insert the LED light ring onto the standpipe by means of the
included adapter. Now, attach the desired sprinkler onto the standpipe.
3. Now, release the cap at the cable of the pump, pull out the sealing plug and
insert the plug of the LED light ring into the socket. Screw the cap nut tight.
4. Put the pump onto a stone in the pond. Please avoid placing the pump
directly at the ground of the pond because here, a particularly high amount
of dirt is sucked in by the pump and the nozzles will be clogged quickly.
5. Please make sure that the accumulator box is switched-off and now connect
the plug of the pump with the socket at the accumulator box.
6. Completely unroll the cable at the accumulator box and insert the plug into
the back side of the solar module.
7. Now, screw the ground spike tight at the back side of the solar module by
means of the cap nut and insert the solar module at a sunny and shadow-
free place.
Note: Before switching on the system, please carefully read the manual of the
accumulator box and pump. It contains important information and notes!
Note: Do not apply force when inserting the solar module. The front side of the
solar module is fragile.
Attention: Risk of injury! A broken may not be repaired anymore and has to be
disposed of it in an environmentally sound manner.
5 m extension cable for the pump: item no: 101740
5 m extension cable for the solar panel: item-no: 101740
Available on www.esotec.de
5. LED Illumination
The LED illumination of the light ring
is automatically activated at dusk.
Apart from the 3 LEDs, a twilight
sensor is installed as light sensor.
This sensor looks like an LED but is
not illuminated.
6. Malfunctions
Solar pump does not work:
- Accumulator box switched-on?
- After a long standstill in winter, it is required to charge the accumulator via
the solar module. The accumulator should be exchanged every 2 - 3 years.
- Accumulator is discharged. Wait for sunshine and, if required, switch-off the
accumulator box for one day and have it recharged.
- Pump clogged. Cleaning according to the manual of the pump!
- Check plug connection at the cable.
7. Storage during the winter
In case of sub-zero temperatures, i.e. during the winter, the pump and the accumu-
lator box have to be stored at a warm place. Before storing it, clean the pump with
lukewarm water as described in the manual of the pump. Switch-off the accumulator
box (position “OFF”), for further notes, see manual of the accumulator box.
!
GB
LED light
LED light
LED light
twilight sensor
no light!
LED lightring
LED holder
standpipe
adapter
sprinkler
sealing plug

9. Safety Notes:
DANGER for children! Keep your children away from small parts which may
present a choking hazard (standpipe and sprinkler) and the packing material
fern. There is danger of suffocation!
WARNING of trip hazards! Please lay the connection cable so that it won’t
constitute a tripping hazard!
CAUTION material damages! If you set up the solar module without any
module mounting you will have to pay attention to an adequate stability. The
solar module may be damaged due to toggling or impact by foreign bodies.
10. Disposal:
Dear customer,
please cooperate in avoiding waste. When you intend to dis-
pose of the product in future, please consider that it contains
valuable raw materials suited for recycling.
Therefore, do not dispose it of with domestic waste but bring
it to a collection point for the recycling of waste electrical and
electronic equipment.
Thank you very much for your cooperation!
Copyright, esotec GmbH
8. Technical Data
Solar pump system: Fountain 5/160 LED
• System voltage: 6 - 9 VDC
Solar module
• Cell type: polycrystalline
• Number of cells: 16 pieces
• Nominal power: 5 Wp
• Nominal voltage: 7,68 V
• Nominal current: 651 mA
• Protection class: IP 65
• Temperature range: -30°C to +75°C
Water pump:
• Operating voltage: 6 V DC
• Power consumption (6V): approx. 1 W
• Max. lift (6V): approx. 0,5 m
• Flow rate (6V): approx. 160 l/h
• Protection class: IP 68
• Operating temperature range: +4 to +40°C
• Dry running: dry run protection
Accumulator box:
• Max. pump runtime with fully
charged accumulator: approx. 4 h
• Accumulator: Li-Fe 6,4 V/ 1,5 Ah
• Max. load current (output): 2 W
• Max. connectable module capacity (input): 5 Wp
• Protection class: IP 44
• Protection grade: III
Customer support:
If you have problems or questions regarding this product, simply contact us!
Monday to Friday 9 am to 12 noon and 1 pm to 4 pm.
By phone: [phone]
By e-mail for ordering spare parts: [email protected]
By e-mail for questions about the product: [email protected]
Product: Manufacturer Item No.: 101920
Battery take-back
- Batteries must not be discarded into domestic waste.
- The consumer is legally required to return batteries after
use, e.g. to public collecting centers or to battery distribu-
tors.
- Contaminant-containing batteries are labeled with the sign
“crossed-out trashcan“ and one of the chemical symbols.
Used batteries should be disposed environmentally friendly
and should not be discarded into domestic waste. Your
dealer is legally required to take back old batteries. Li-Fe