ECOVACS DEEBOT T20 OMNI User manual

平面印刷品基本技术要求
科沃斯机器人股份有限公司
物料名称 T20 OMNI 美国说明书 尺 寸 145*210mm
型 号 ZJ2230 印刷颜色 单色 K 印刷 +Pantone 279C
物料编码 451-2230-2500 装订方式 骑马钉
版 次 A00 页 数 68p
材 质 封面 157 哑粉纸 + 内页 105g 哑粉纸 比 例 1:1
变更记录：
设计 审核 批准
ECOVACS：机密图档
PLD
2023.03.03
徐天琪

Instruction Manual

2EN
Important Safety Instructions
1. Do not allow to be used as a toy. Close
attention is necessary when used by or near
children.
2. Clear the area to be cleaned. Remove power
cords and small objects from the floor that
could entangle the Appliance. Tuck rug fringe
under the rug base, and lift items such as
curtains and tablecloths off the floor.
3. If there is a drop off in the cleaning area due
to a step or stairs, you should operate the
Appliance to ensure that it can detect the
step without falling over the edge. It may
become necessary to place a physical barrier
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE.
When using an electrical appliance, basic
precautions should always be followed, including the
following:
WARNING:
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire or serious injury.
at the edge to keep the unit from falling. Make
sure the physical barrier is not a trip hazard.
4. Only use as described in this manual. Only
use attachments recommended or sold by
the manufacturer.
5. Do not handle plug or appliance with wet
hands.
6. Non-rechargeable batteries are prohibited.
7. Do not use without dust bin and/or filters in
place.
8. Do not operate the vacuum in an area where
there are lit candles or fragile objects on the
floor to be cleaned.
9. Do not use and store in extremely hot or
cold environments (below -5˚C /23˚F or
above 40˚C/104˚F). Please charge the robot
in temperature above 0°C/32°F and below
40°C/104°F.
10. Keep hair, loose clothing, fingers, and all
parts of body away from any openings and
moving parts.
11. Do not operate the Appliance in a room
where an infant or child is sleeping.
12. For INDOOR use ONLY. Do not use the
Appliance in outdoor, commercial or industrial

3EN
environments. Do not use Appliance on wet
surfaces or surfaces with standing water.
13. Do not allow the Appliance to pick up large
objects like stones, large pieces of paper or
any item that may clog the Appliance.
14. Do not use to pick up flammable or
combustible materials such as gasoline,
printer or copier toner, or use in areas where
they may be present.
15. Do not pick up anything that is burning or
smoking, such as cigarettes, matches, hot
ashes, or anything that could cause a fire.
16. Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce
air flow.
17. Take care not to damage the power cord. Do
not pull on or carry the Appliance or Docking
Station by the power cord, use the power
cord as a handle, close a door on the power
cord, or pull power cord around sharp edges
or corners. Do not run Appliance and Docking
station over the power cord. Keep power
cord away from hot surfaces. Do not unplug
by pulling on cord. To unplug, grasp the plug,
not the cord.
18. If the power cord is damaged, it must be
replaced by the manufacturer or its service
agent in order to avoid a hazard.
19. Do not use with a damaged power cord or
plug. Do not use the Appliance or Docking
Station if it is not working properly, has been
dropped, damaged, left outdoors, or come in
contact with water. It must be repaired by the
manufacturer or its service agent in order to
avoid a hazard.
20. Turn OFF the power switch before cleaning
or maintaining the Appliance. Turn off all
controls before unplugging. Always turn
off this appliance before connecting or
disconnecting motorized nozzle.
21. Remove the Appliance from the Docking
Station, and turn OFF the power switch to
the Appliance before removing the battery for
disposal of the Appliance.
22. The battery must be removed and discarded
according to local laws and regulations
before disposal of the Appliance.
23. Please dispose of used batteries according to
local laws and regulations.

4EN
24. Do not incinerate the Appliance even if it is
severely damaged. The batteries can explode
in a fire.
25. When not using the Docking Station, unplug
from outlet when not in use and before
servicing.
26. The Appliance must be used in accordance
with the directions in this Instruction Manual.
ECOVACS ROBOTICS cannot be held liable
or responsible for any damages or injuries
caused by improper use.
27. Prevent unintentional starting. Ensure the
switch is in the off position before connecting
to battery pack, picking up or carrying the
appliance.
28. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
29. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
30. Do not use a battery pack or appliance that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
31. Do not expose a battery pack or appliance
to fire or excessive temperature. Exposure to
fire or temperature above 130°C may cause
explosion. The temperature of 130°C can be
replaced by the temperature of 265°F.
32. Follow all charging instructions and do
not charge the battery pack or appliance
outside of the temperature range specified
in the instructions. Charging improperly or at
temperatures outside of the specified range
may damage the battery and increase the risk
of fire.
33. Have servicing performed by a qualified repair
person using only identical replacement
parts. This will ensure that the safety of the
product is maintained.
34. Do not modify or attempt to repair the
appliance or the battery pack (as applicable)
except as indicated in the instructions for use

5EN
and care.
35. Place the cords from other appliances out of
the area to be cleaned.
36. Do not operate the vacuum in a room that
has lit candles on furniture that the vacuum
may accidentally hit or bump into.
37. Do not allow children to sit on the vacuum.
38. Use only as described in this manual.
Use only manufacturer’s recommended
attachments.
39. Recharge only with the charger specified by
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk
of fire when used with another battery pack.
40. Use appliances only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and
fire.
41. The robot contains batteries that are only
replaceable by skilled persons. To replace
the robot’s battery, please contact Customer
Service.
42. If the robot will not be used for a long time,
fully charge the robot and power OFF for
storage and unplug the Docking Station.
43. To Reduce The Risk Of Electric Shock – Do
not use on wet surfaces. Do not expose to
rain. Store indoors.
44. To Reduce The Risk Of Injury From Moving
Parts – Unplug Before Servicing.
45. Risk Of Injury. Brush May Start Unexpectedly.
Unplug Before Cleaning or Servicing.
46. To reduce the risk of injury, user must read
instruction manual.
47. To Reduce The Risk Of Electric Shock – Do
not use outdoors or on wet surfaces.
48. Please make sure your power supply voltage
matches the power voltage marked on the
Docking Station.
49. Do not use the Docking Station if it is
damaged.
50. The plug must be removed from the
receptacle before cleaning or maintaining
the Docking Station.
51. Connect to a properly grounded outlet only.
See GroundingInstructions.GROUNDING
INSTRUCTIONSThis appliance must
be grounded. If it should malfunction or
breakdown, grounding provides apath
of least resistance for electric current to

6EN
Federal Communications Commission (FCC)
Interference Statement
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
Direct current
Alternating current
This Device Complies with DHHS Radiation Rules,
21CFR Chapter 1, Subchapter J.
reduce the risk of electric shock. This
appliance isequipped with a cord having
an equipment-grounding conductor and
grounding plug. The plugmust be inserted
into an appropriate outlet that is properly
installed and grounded inaccordance with
all local codes and ordinances.WARNING
– Improper connection of the equipment-
grounding conductor can result in a risk
ofelectric shock. Check with a qualified
electrician or service person if you are in
doubt as towhether the outlet is properly
grounded. Do not modify the plug provided
with the appliance – ifit will not fit the outlet,
have a proper outlet installed by a qualified
electrician.This appliance is for use on a
nominal 120-V circuit and has a grounding
attachmentplug that looks like the plug
illustrated as the following photo . Make
sure that theappliance is connected to an
outlet having the same configuration as the
plug. Noadaptor should be used with this
appliance.

7EN
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
RF exposure warning
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
This equipment must be installed and operated
in accordance with provided instructions and
the antenna(s) used for this transmitter must be
installed to provide a separation distance of at
least 20 cm from all persons and must not be
collocated or operating in conjunction with any
other antenna or transmitter.
MPE caution (for mobile device under Part
15.247)
To satisfy FCC&ICRF exposure requirements, a
separation distance of 20cm or moreshould be
maintained between the antenna of this device
interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Caution: Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user's authority to
operate the equipment.
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science

8EN
Device Update
Typically, some devices are updated bi-monthly,
but not always so specific.
Some devices, especially those that went on sale
more than three years ago, will only be updated if
a critical vulnerability is found and fixed.
and persons during device operation.
To ensure compliance, operations at closer than
this distance is not recommended.
To disable Wi-Fi module on DEEBOT, power the
robot ON. Place the robot on the OMNI Station
making sure the Charging Contacts on DEEBOT
and the Station Pins make a connection.
Press and hold the Button on the Station for
30 seconds. And press and hold the AUTO Mode
Button on the robot for 30 seconds.
To enable Wi-Fi module on DEEBOT, power the
robot OFF and then power ON. And unplug the
Station and plug it again.
SAVE THESE INSTRUCTIONS
For INDOOR household use ONLY.
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
To satisfy FCC&ICRF exposure requirements, a
separation distance of 20cm or more should be
maintained between the antenna of this device
and persons during device operation.
To ensure compliance, operations at closer than
this distance is not recommended.
GROUNDING
PIN
GROUNDED
OUTLET

9EN
Package Contents
Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specications
are subject to changes without notice.
Robot OMNI Station
Instruction Manual Dual Side Brushes
Power Cord Mopping Pad Plates
Cleaning Brush
Washable Mopping Pads
Dust BagMulti-Function Cleaning Tool
Instruction Manual

10EN
Product Diagram
Robot
Dust Bin
Top Cover
AUTO Mode Button
TrueDetect 3D
Sensor
Anti-
collision
Sensors
and Bumper
TrueMapping
Distance Sensor
Wi-Fi Status
Indicator
Microphone
RESET Button
Dust Bag Handle
Release Button
Dust Disposal Port
Filter Net
High
Efciency Filter
Power Switch
"I"åç=ON
" "=OFF
Data transfer port
For professional
maintenance
personnel only
Con󽗉guring the network: During the connection, press the RESET Button, and
there will be voice prompts to guide you through the connection.
Restore to default settings: Press and hold RESET button for 5 seconds. After
you hear the voice prompt, the startup music will be played and the robot will
be restored to default settings. Please use with caution.

11 EN
Anti-drop Sensors
Anti-drop
Sensors
Floating Main
Brush Release
Button
Universal Wheel
Dual Side Brushes
Driving Wheels
Floating Main
Brush
Ultrasonic Sensor
Bottom View
Mounting Slots
for Mopping Pad
Assembly
Washable Mopping Pads
Mopping Pad Plates
Mopping Pad Assembly
Charging Contacts

12EN
OMNI Station
Dirty Water Tank
Top Cover
Clean
Water Tank
Water Inlet
Start/Pause/
Self-cleaning
Button
Dust Collection
Cabin
Pop-up Button
(Below the Dust
Collection Cabin )
Filter
Dust Bag
Dust Bag Handle
Press: Start/Pause/Self-cleaning Button
Press and hold the button for 5 seconds:to add water to or
drain the water out of Cleaning Sink
Cleaning Sink
Control Panel Botton

13 EN
Sensors
Name Functional Description
TrueMapping Distance Sensor
With Laser Ranging-measuring the distance between DEEBOT and surroundings through the
time difference of reection, it can map according to the objects around while DEEBOT is
moving. Detection of 10m
TrueDetect 3D Sensor
The TrueDetect 3D structured light sensor scans the object with a line laser and collect images
with a monocular camera, and generates the three-dimensional coordinates of the object
through image algorithms to identify the size of the object. The detection distance is 0.35m
Microphone Vibrating the diaphragm through air by human voice, it can realize Voice Recording and ask
DEEBOT to complete the assigned work by Voice Control. Effective wake of 8m
Anti-drop Sensor
With Infrared Ranging-detecting the distance between the bottom of DEEBOT and ground by
Infrared Sensor at the bottom, DEEBOT will not move forward when there are stairs in front or
the identied distance exceeds the preset one, realizing the Anti-drop. The trigger distance is
60mm
Carpet Detection Sensor
The difference in energy of the ultrasonic echo signal on different surfaces is used to identify
the oor material and help DEEBOT to adjust the cleaning strategy automatically. Drive
frequency 290kHZ

14EN
Notes Before Cleaning
Tidy up the area to be cleaned by putting furniture, such as chairs, in
their proper place.
During the rst use, make sure each room door is open to help DEEBOT
fully explore your house.
It may be necessary to place a physical barrier at the edge of a drop to
stop the unit from falling over the edge. Put away objects including cables, cloths and slippers, etc.
on the oor to improve the cleaning efciency.
Before using the product on a rug with tasseled edges, please
fold the rug edges under.
Clean the AIVI Camera and TrueMapping Distance Sensor with
a clean cloth, and avoid using any detergent or cleaning spray.

15 EN
Click!
ECOVACS HOME App
To enjoy all available features, it is recommended to control your DEEBOT via
the ECOVACS HOME app.
Make sure the colors of Dual Side Brushes are consistent with those of mounting
slots.
Before using DEEBOT, please remove all protective lms or
protective strips on DEEBOT and OMNI Station.
Wi-Fi Indicator Light
Before you start, make sure that:
Install the Dual Side Brushes
• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz or 2.4/5 GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on DEEBOT is slowly ashing.
Slowly flashing Disconnected to Wi-Fi or
waiting for Wi-Fi connection
Rapidly flashing Connecting to Wi-Fi
Solid Connected to Wi-Fi
Quick Start Wi-Fi Connection
Before Wi-Fi setup, make sure DEEBOT, mobile phone, and Wi-Fi network
meet the following requirements.
DEEBOT and Mobile Phone Requirements
• DEEBOT is fully charged and the power switch of DEEBOT is turned on.
• Wi-Fi status light slowly ashes.
• Turn off mobile phone’s cellular data (you can turn it back on after setup).
Wi-Fi Network Requirements
• You are using a 2.4GHz or 2.4/5 GHz mixed network.
• Your router supports 802.11b/g/n and IPv4 protocol.
• Do not use a VPN (Virtual Private Network) or Proxy Server.
• Do not use a hidden network.
• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
• WEP EAP (Enterprise Authentication Protocol) is not supported.
• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North
America (refer to local regulatory agency).
• If you are using a network extender/repeater, the network name (SSID) and
password are the same as your primary network.
After Wi-Fi connection, DEEBOT will enter into Networked Standby mode if it has
no signal input within 10 minutes.
Please be aware that the realization of intelligent functions such as remote startup,
voice interaction, 2D/3D map display and control settings, and personalized
cleaning (depending on different products) requires users to download and use
ECOVACS HOME App, which is constantly updated. You need to agree to our
Privacy Policy and User Agreement before we can process some of your basic and
necessary information and enable you to operate the product.If you do not agree
with our Privacy Policy and User Agreement, some of the aforementioned intelligent
functions cannot be realized through ECOVACS HOME App, but you can still use
the basic functions of this product for manual operation.

16EN
Keep the area around the Station clear of objects and reective object surfaces.
Charging DEEBOT
1
2
Assemble OMNI Station
OMNI Station Placement
* If there are reective objects such as mirrors and reective skirting lines near the
Station, the bottom 14cm of that should be covered.
Do not place the Station under direct sunlight.
It is recommended to place the Station on the hard oor to experience complete
functions of the robot.
0.05m (0.16’)

0.05m (0.16’)

0.8m (2.62’)
3Add Water to Clean Water Tank
Note: It is recommended to use ECOVACS DEEBOT Cleaning Solution (sold
separately). Using other cleanig solution may cause DEEBOT slipping, water tank
block and other problems.
×10
DEEBOT cannot be charged when being powered OFF.
4Power ON
Note: I = ON, O = OFF.

17 EN
1
When creating a map for the rst time, please follow DEEBOT to help eliminate some minor issues.
For example, DEEBOT may get stuck under the furniture. Please refer to the following solutions:
1. Raise the furniture if possible; 2. Cover the bottom of the furniture; 3. Set up Virtual Boundary via the App.
Start
Operating DEEBOT
Tap on DEEBOT or on the OMNI Station to start
2Pause/Wake Up
Note: The indicator light will go out after the robot is paused for a few minutes.
Press the AUTO Mode Button on DEEBOT to wake up the robot.
Note: For the rst-time cleaning, please ensure that DEEBOT is fully charged.
Tap on DEEBOT or on the OMNI Station to pause.
3
Tap for 3 seconds to recall DEEBOT to the OMNI Station.
Back to Station
Note: When DEEBOT is not working, it is recommended to keep it switched ON
and charging.
3s

18EN
1
2
Attach the Mopping Pads and Mopping Pad Plates.
Mop
Note:
1. To prolong the service life of the reservoir, do not frequently remove washable
mopping pads.
2. Do not use a rag or any other object to scratch the Moping Pad Plates.
3. When the ECOVACS HOME App prompts that the mops need to be replaced,
please replace them in time.
Explore more accessories at ECOVACS HOME App or at https://www.ecovacs.
com/global.
Mopping
Tap on DEEBOT or on the OMNI Station to start mopping.
You would hear a “click” when the Mopping Pad Plates is properly
installed.
Press the button to Start/Pause/Continue DEEBOT Cleaning
OMNI Station

19 EN
To keep DEEBOT running at peak performance, perform maintenance tasks and replace parts with the following frequencies:
A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: ECOVACS manufactures various replacement parts and ttings. Please contact Customer Service for more information on replacement parts.
Robot Part Maintenance Frequency Replacement Frequency
Washable Mopping Pad / Every 1-2 months
Dust Bag / Replace when voice prompts
Dual Side Brushes Once every 2 weeks Every 3-6 months
Floating Main Brush Once per week Every 6-12 months
Sponge Filter/High Efciency Filter Once per week Every 3-6 months
TrueDetect 3D Sensor
TrueMapping Distance Sensor
Universal Wheel
Anti-Drop Sensors
Bumper
Charging Contacts
OMNI Station Pins
Once per week /
Cleaning Sink Once every 2 weeks /
Clean Water Tank Once every 3 months /
Dirty Water Tank After each mopping /
Dust Collection Cabin Once per month /
OMNI Station Once per month /
Filter Once per month /
Regular Maintenance
Before performing cleaning and maintenance tasks on DEEBOT, turn the robot OFF and unplug the OMNI Station.