ECR International EMI Deluxe Heat DHWAL12DA User manual

ECR International Inc.
2201 Dwyer Avenue, Utica, NY 13501
Tel. [phone]
www.ecrinternational.com
PN 615000260 REV. B[10/01/2021]
PRESENTS
WALL AIR HANDLER
DUCTLESS SPLIT SYSTEM
User Manual
IMPORTANT NOTE:
Read this manual carefully before installing
or operating your new air conditioning
unit. Make sure to save this manual for
future reference.
MODELS
DHWAL09DA 9 kBtu/h
DHWAL12DA 12 kBtu/h
DHWAL18DA 18 kBtu/h
DHWAL24DA 24 kBtu/h

Table of Contents
Owner’s Manual
Safety Precautions.................................................................................................. 3
Unit Specifications and Features ........................................................................ 5
1
2
Care and Maintenance.......................................................................................10
Troubleshooting......................................................................................................12
3
4
1. Indoor unit display..................................................................................5
2.
Other features ................................................................................5
3.
Normal Operating temperature . ................................................................. 8
4.
. Setting angle of airflow . ..........................................................................9
Disposal Guidelines
This appliance contains refrigerant and other potentially hazardous materials. When disposing of
this appliance, the law requires special collection and treatment. Do not dispose of this product
as household waste or unsorted municipal waste.
Dispose of the appliance at designated municipal electronic waste collection
facility.
Disposing of this appliance in the forest or other natural surroundings endangers your health and is
bad for the environment. Hazardous substances may leak into the ground water and enter the food
chain.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that waste electrical and
eletrical equipment should not be mixed with general household waste.
PN 615000260 REV. B [10/01/2021]

Page 3 
Safety
Precautions
Read Safety Precautions Before Operation and Installation
Incorrect installation due to not following instructions can cause serious injury or
damage. The seriousness of potential damage or injuries is classified as either a WARNING or
CAUTION.
• If there is a burning smell immediately disconnect the power. Call your dealer for instructions to
avoid electric shock, fire or injury.
• Do not insert fingers, rods or other objects into the air inlet or outlet. This may cause inj ury,
fan may be rotating at high speeds.
• Do not use flammable sprays such as hair spray, lacquer or paint near the unit. This may cause
fire or combustion.
•
Do not
operate the air conditioner near or around combustible gases. Emitted gas may collect
around the unit and cause explosion.
•
Do not
•
•
Do not
expose your body directly to cool air for a prolonged period of time.
•
•
1
Safety Precautions
Do not
allow children to play with the air conditioner. Children must be supervised around the
unit at all times.
operate your air conditioner in a wet room such as a bathroom or laundry room. Too
much exposure to water can cause electrical components to short circuit.
If the air conditioner is used with burners or other heating devices, thoroughly ventilate the
room to avoid oxygen deficiency.
In certain environments, such as kitchens, server rooms, etc., the use of specially designed air-
conditioning units is highly recommended.
!WARNING
CAUTION INDICATES A HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, COULD RESULT IN ,MINOR OR MODERATE INJURY.
CAUTIONCAUTION
WARNING INDICATES A HAZARDOUS SITUATION WHICH, IF
NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY
WARNING
!WARNING
WARNING INDICATES A HAZARDOUS SITUATION WHICH, IF
NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY
!
!
PN 615000260 REV. B [10/01/2021]

Page 4 
Safety
Precautions
CLEANING AND MAINTENANCE WARNINGS
• Electric Shock Hazard! Turn off the unit and disconnect the power before cleaning. Failure to
do so can cause electrical shock.
•Do not
clean the air conditioner with excessive amounts of water.
•Do not
clean the air conditioner with combustible cleaning agents. Combustible cleaning agents
can cause fire or deformation.
Note about Fluorinated Gasses
1.
This air-conditioning unit contains fluorinated greenhouse gasses. For specific information on the
type of gas and the amount, please refer to the relevant label on the unit.
2. Installation, service, maintenance and repair of this unit shall be performed by a certified
technician.
3. Product removal and recycling shall be performed by a certified technician.
4. When the unit is checked for leaks, proper record-keeping of all checks is recommended.
WARNING
!
CAUTIONCAUTION
!
• Turn off the air conditioner and disconnect the power if you are not going to use it for a long time.
• Turn off and unplug the unit during storms.
• Make sure that water condensation can drain unhindered from the unit.
•Do not operate the air conditioner with wet hands. This may cause electric shock.
•Do not use device for any other purpose than its intended use.
•Do not climb onto or place objects on top of the outdoor unit.
•
•
Do not allow the air conditioner to operate for long periods of time with doors or windows open,
or if the humidity is very high.
How to install the appliance to its support, please refer to the “INSTALLATION MANUAL” for details
in "indoor unit installation" and "outdoor unit installation" sections.
PN 615000260 REV. B [10/01/2021]

Page 5 
Unit Specifications and Features 2
Unit
Specifications
and Features
Indoor unit display
“ ” for 3 seconds when:
• TIMER ON is set
• FRESH, SWING, TURBO, SILENCE or SOLAR PV ECO feature is turned on
“ ” for 3 seconds when:
• TIMER OFF is set
• FRESH, SWING, TURBO, SILENCE or SOLAR PV ECO feature is turned off
“
“
“
“
” when anti-cold air feature is turned on
” when defrosting(cooling & heating units)
” when unit is self-cleaning
” when 4.5°F (8°C) heating feature is turned on
Power Cable (Some Units )
Remote Control Remote Control
Holder (Some Units)
Display Code
Meanings
Functional Filter
(On Front of Main Filter - Some Units)
Louver
Front Panel
Signal receiver
Signal receiver
Display window
(A)
(C)
“ ” display the temperature setting or room temperature. When error occurs,
it displays error code. Some units can display the following functions:
“ ” when FRESH feature is turned on
“ ” when defrosting(cooling & heating units).
“ ” when the unit is operational.
“ ” when Timer is set.
(B)
PN 615000260 REV. B [10/01/2021]

Page 6 
Unit
Specifications
and Features
“ ” for 3 seconds when:
• TIMER ON is set
• FRESH, SWING, TURBO, SILENCE or SOLAR PV ECO feature is turned on
“ ” for 3 seconds when:
• TIMER OFF is set
• FRESH, SWING, TURBO, SILENCE or SOLAR PV ECO feature is turned off
“ ” when defrosting(cooling & heating units)
“ ” when anti-cold air feature is turned on
“ ” when unit is self-cleaning
“ ” when 8 C heating feature is turned on
Power Cable (Some Units )
Remote Control Remote Control
Holder (Some Units)
Display Code
Meanings
Functional Filter
(On Front of Main Filter - Some Units)
Louver
Front Panel
Display window
(D)
Display window
(E)
Display window
(F)
“ ” display the temperature setting or room temperature. When error occurs,
it displays error code. For some units, it can display the following functions:
“ fresh ” when FRESH feature is turned on
“ defrost ” when defrosting(cooling & heating units).
“ run ” when the unit is operational.
“ timer ” when Timer is set.
“ turbo ” when Turbo feature is turned on
“ auto ” when Auto mode is activated
fresh defrost run timer turbo defrost run timer auto defrost run timer
NOTE: Different models have different front panel and display window. Not all the indicators
described are available for your air conditioner Please check the indoor display window of the
unit you purchased.
Illustrations in this manual are for explanatory purposes. The actual shape of your indoor unit
may be slightly different. The actual shape shall prevail.
PN 615000260 REV. B [10/01/2021]

Unit
Specifications
and Features
Page 7 
Other Features
•Auto-Restart(some units)
If the unit loses power, it will automatically
restart with the prior settings once power has
been restored.
•Anti-mildew (some units)
When turning off the unit from COOL, AUTO
(COOL), or DRY modes, the air conditioner will
continue operate at very low power to dry up
condensed water and prevent mildew growth.
•Wireless Control (some units)
Wireless control allows you to control your air
conditioner using your mobile phone and a
wireless connection.
•Louver Angle Memory(some units)
When turning on your unit, the louver will
automatically resume its former angle.
•Refrigerant Leakage Detection
(some units)
The indoor unit will automatically display “EC”
when it detects refrigerant leakage.
The SLEEP function is used to decrease
energy use while you sleep (and don’t
need the same temperature settings to
stay comfortable). This function can only
be activated via remote control. And the
Sleep function is not available in FAN or
DRY mode.
Sleep Operation
•
For the USB device access, replacement,
maintenance operations must be carried
out by professional staff.
Set
temperature
1hr
Keep
running
SLEEP Operation
Saving energy during sleep
Heat mode( -2 F/1 C) per hour
for the first two hours
Cool mode(+2 F/1 C) per hour
for the first two hours
1hr
A guide on using the infrared remote is not
included in this literature package. Not all
the functions are available for the air
conditioner, please check the indoor display
and remote control of the unit you purchased.
Press the SLEEP button when you are
ready to go to sleep. When in COOL mode,
the unit will increase the temperature
by 2°F (1°C) after 1 hour, and will increase
an additional 2°F (1°C) after another hour.
When in HEAT mode, the unit will decrease
the temperature by 2°F (1°C) after 1 hour,
and will decrease an additional 2°F (1°C)
after another hour.
For some units, the sleep feature will stop
after 8 hours and the system will keep
running with final situation.
For some units, the unit will turn off after
7 hours.
Set
temperature
1hr
7 hours
timer o
SLEEP Operation
Saving energy during sleep
Heat mode( -2 F/1 C) per hour
for the first two hours
Cool mode(+2 F/1 C) per hour
for the first two hours
1hr
Hold the new
temperature
for 5 hours
NOTE:
Best working conditions(the energy
efficiency can be affected if not set
under these conditions):
--The best angle of louvers is the default
angle of cooling mode.
-- The best way of setting the angle of
louvers at heating mode is: run the
unit for 5 minutes and then use the
remote controller to set the louvers at
the default angle of cooling mode.
PN 615000260 REV. B [10/01/2021]

Unit
Specifications
and Features
Page 8 
COOL mode HEAT mode DRY mode
Room Temperature (17°C - 32°C)
63°F - 90°F
(0°C - 30°C)
32°F - 86°F
(10°C - 32°C)
50°F - 90°F
Outdoor
Temperature
32°F - 122°F
(0°C - 50°C)
5°F - 86°F
(-15°C - 30°C)
32°F - 122°F
(0°C - 50°C)
32°F - 126°F
(0°C - 52°C)
(For special
tropical models)
32°F - 126°F
(0°C - 52°C)
(For special
tropical models)
5°F - 122°F
(-15°C - 50°C)
(For models with
low temp.
cooling systems.)
To further optimize the performance of your unit, do the following:
•Keep doors and windows closed.
•Limit energy usage by using TIMER ON and TIMER OFF functions.
•Do not block air inlets or outlets.
•Regularly inspect and clean air filters.
FOR OUTDOOR UNITS
WITH AUXILIARY
ELECTRIC HEATER
Inverter Split Type
When outside
temperature is below 0°C
(32°F ), we strongly
recommend keeping the
unit plugged in at all
time to ensure smooth
ongoing performance.
NOTE: Room relative humidity less than 80%. If the air conditioner operates in excess of this
figure, the surface of the air conditioner may attract condensation. Please sets the vertical air
flow louver to its maximum angle (vertically to the floor), and set HIGH fan mode.
When your air conditioner is used outside of the following temperature ranges, certain safety
protection features will activate and cause the unit to disable.
Normal Operating temperature
PN 615000260 REV. B [10/01/2021]

Page 9 
Setting vertical angle of air flow
While the unit is on, use the SWING/DIRECT
button on remote control to set the direction
(vertical angle) of airflow. Please refer to the
Remote Control Manual for details.
The horizontal angle of the airflow must be set
manually. Grip the deflector rod (See Fig.B)
and manually adjust it to your preferred direction.
For some units, the horizontal angle of the airflow
can be set by remote control. please refer to the
Remote Control Manual.
NOTE ON LOUVER ANGLES
When using COOL or DRY mode, do not set
louver at too vertical an angle for long periods
of time. This can cause water to condense on
the louver blade, which will drop on your floor
or furnishings.
When using COOL or HEAT mode, setting the
louver at too vertical an angle can reduce the
performance of the unit due to restricted air
flow.
Do not put your fingers in or near the blower
and suction side of the unit. The high-speed
fan inside the unit may cause injury.
Fig. B
Fig. A
Setting Angle of Air Flow
Setting horizontal angle of air flow
•
Unit
Specifications
and Features
To operate your unit manually:
1. Open the front panel of the indoor unit.
2. Locate the MANUAL CONTROL button on
the right-hand side of the unit.
3. Press the MANUAL CONTROL button one
time to activate FORCED AUTO mode.
4. Press the MANUAL CONTROL button again
to activate FORCED COOLING mode.
5. Press the MANUAL CONTROL button a third
time to turn the unit off.
6. Close the front panel.
The manual button is intended for testing purposes
and emergency operation only. Please do not use this
function unless the remote control is lost and it is
absolutely necessary. To restore regular operation,
use the remote control to activate the unit. Unit must
be turned off before manual operation.
Manual Operation(without remote) Deflector
rod
Manual control
button
Range
NOTE: Do not move louver by hand. This will
cause the louver to become out of sync. If this
occurs, turn off the unit and unplug it for a few
seconds, then restart the unit. This will reset the
louver.
IMPORTANT!
!
cACAUTION
!
PN 615000260 REV. B [10/01/2021]

Page 10 
Cleaning Your Indoor Unit
IMPORTANT
Only use a soft, dry cloth to wipe the unit clean.
If the unit is especially dirty, you can use a cloth
soaked in warm water to wipe it clean.
• Do not use chemicals or chemically treated
cloths to clean the unit
• Do not use benzene, paint thinner,
polishing powder or other solvents to clean
the unit. They can cause the plastic surface
to crack or deform.
• Do not use water hotter than 104°F (40°C)
to clean the front panel. This can cause the
panel to deform or become discolored.
Care and Maintenance 3
Cleaning Your Air Filter
A clogged air conditioner can reduce the cooling
efficiency of your unit, and can also be bad for
your health. Make sure to clean the filter once
every two weeks.
1. Lift the front panel of the indoor unit.
2. Grip the tab on the end of the filter, lift it
up,then
pull it towards yourself.
3. Now pull the filter out.
4. If your filter has a small air freshening filter,
unclip it from the larger filter. Clean this air
freshening filter with a hand-held vacuum.
5. Clean the large air filter with warm, soapy
water. Be sure to use a mild detergent.
6. Rinse the filter with fresh water, then shake
off excess water.
7. Dry it in a cool, dry place, and refrain from
exposing it to direct sunlight.
8. When dry, re-clip the air freshening filter to
the larger filter, then slide it back into the
indoor unit.
9. Close the front panel of the indoor unit.
Do not touch air freshening (Plasma) filter for
at least 10 minutes after turning off the unit.
Filter Tabs
Remove air freshening filter from back of
larger filter (some units)
Plasma
Air filter
Hold the two parts of Plasma which
marked with signal and lift it. Then
you can open the cover of the the
plasma and remove the filter
(some units)
Care and
Maintenance
! cAWARNING
!
ALWAYS TURN OFF YOUR AIR CONDITIONER
SYSTEM AND DISCONNECT ITS POWER SUPPLY
BEFORE CLEANING OR MAINTENANCE.
!
cACAUTION
!
PN 615000260 REV. B [10/01/2021]