EDFM FX LOOPER User manual

FX LOOPER + EFFECTS CONTROLLER

FX LOOPER + EFFECTS CONTROLLER
USER Manual
FX LOOPER + EFFECTS CONTROLLER
Features:
6 banks with heavy duty foot switch and unique color status indicators.
True BYPASS heavy duty foot switch (click type) with LED indicator.
MUTE/TUNER heavy duty foot switch (click type) with LED indicator for silent tuning.
Switchable Buffer Circuit for long cable runs.
Buffer placement in the effects single path.
6 Effects send and return jacks.
All true bypass switching.
Adjustable LED Brightness Control.
Small footprint for actual on pedalboard placement. (8 1/8 x 4 13/16 x 2 3/8)
Operates on +9V DC Power supply, +9V Battery or both (Not Included).

CONTROLS & JACKS LAYOUT
TOP SIDE
1. BANKS (6)
1. Each of the 6 banks consist of a heavy duty foot switch, LED on/off indicator.
1. FX-1 through FX-6 Effects Foot Switch's - Heavy duty (click) Switches. Engages/disengages the effects that are connected to
their corresponding send and return jacks.
1. LED's - When illuminated all effects plugged into the corresponding send and return jacks are placed in the instrument signal
path. There are 6 different LED color's for each effect bank. FX-1 Blue, FX-2 Orange, FX-3 Yellow, FX-4 Pink, FX-5 Aqua, FX-6 Cyan.
2. BYPASS - When engaged the input signal path bypasses all effects inputs and goes directly to Output jack.
*Note: If the BUFFER switch is in the engaged ON position, then the BYPASSED signal will be routed through the Buffer circuit
then to the OUTPUT jack.
3. TUNER/MUTE - When engaged the Input device is muted and no signal is routed to the OUTPUT jack. This will also engage the
TUNER jack for silent tuning of your instrument using a tuner of your choice. This allows you to remove your tuner out of your
instruments signal path and leave the tuner on all the time.

4. BUFFER OFF-ON switch -When in the ON position the Buffer circuit is engaged, when in the OFF position the Buffer circuit is
completely removed from the instruments signal path using True Bypass switching. See *NOTE: Below
5. BUFFER SELECT switch -The Buffer Select switch allows you have control of where the actual Buffer circuit is place in the
instruments signal path. When the switch is in the OFF/ALL position the Buffer circuit is placed after the Instrument Input jack and
all effects will be buffered. When in the 4-6 position the Buffer circuit is place just before the effects plugged into the S4,R4 jacks,
leaving the effects plugged into the S,R 1-3 jacks unbuffered.
*NOTE: To turn off the buffer, both the BUFFER and BUFFER SELECT switches must be in the OFF (left) position. If the BUFFER
SELECT switch is in the 4-6 position there will be no signal at the output jack.
6. LED's Brightness Adjust - Turning the knob counter-clock wise dim's the LED's. Turning it clock wise brightens the LED's. The
Brightness Adjust and the Buffer on/off LED's will not be affect by the brightness adjustment knob.
*NOTE: The brighter you set the LED's the shorter the battery life will be.
BACK SIDE
A total of 6 individual effects can be plugged into the FX Looper +. You can also combine multiple effects into one channel.
Jacks for channel 1 - 5 are located on the back side with 6 located on the left side.
The top row are all SEND jacks and the bottom row are all RETURN jacks.
7. 1S-5S Send jack's - Connect this 1/4 inch jack to your effect or effects input jack.
8. 1R-5R Return jack's - Connect this 1/4 inch jack to your effect or effects output jack.

RIGHT SIDE
9. INPUT jack - Connect any 1/4" instrument or other equipment here. DO NOT INCERT A STEREO PLUG!
10. PWR power adapter jack - Plug a +9V DC female negative tip, 5.5mm O.D. x 2.1mm I.D. barrel style DC power supply or
wall-wart adapter (Not Included). Both a power supply and a 9V battery can be used at the same time. If the power supply
connector comes unplugged the unit will automatically switch to battery power.
LEFT SIDE
11. TUNER jack, Connect this 1/4 inch jack to your tuner input jack. Your tuner output jack is not used, leave unplugged.
12. 6R Return jack, Connect this 1/4 inch jack to your effect or effects output jack.
13. 6S Send jack, Connect this 1/4 inch jack to your effect or effects input jack.
14. OUTPUT jack, Connect this 1/4 inch jack to your amplifier or recording devices input.

FRONT SIDE
15. 9Volt Battery Compartment - To open gently squeeze the tab on the right side inward with your finger tip and pull. Insert a 9volt
battery (not included) observing proper polarity. The positive side of the battery (the smaller post) goes towards the top. If the
compartment door will not close and latch make sure the battery is inserted all the way and that the positive side is towards the top.
*NOTE: The input jack acts as a switch for the 9V battery. If a plug is inserted into the input and no external Power supply is connected to
the PWR jack then the unit will be on all the time and shorten the battery life span. If a Power Supply is connected to the PWR jack then
the battery is eliminated from the power circuit. Unplug instruments from the INPUT jack to save battery life if no external power supply
is used. NEVER INCERT A STEREO PLUG INTO THE INPUT JACK!
SN:
LIMITED WARRANTY
Your EDFM FX LOOPER + Effect Controller pedal comes with a 1 year limited warranty on parts and workmanship. During the
warranty period EDFM will repair or replace, at our option, defective parts or pedal free of charge, and return them to the owner.
Warranty service does not include: Opened Units, Damaged, Modified, Misused pedals, Powder Coating and Graphics/Lettering, and
such will be subject to a standard repair charge. It is the product owners responsibility to securely package the product for shipment, pay
for shipping or transportation, or pay for any international shipping charges for repair returns to EDFM.