Edge Lighting Cody CPL-6-P Series User manual

Installation Instructions for Cody 6" Plug-In Picture Light
904-CPL-6-P-01
Install the Fixture
1
CPL-6-_-P
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: [phone]
Fax: [phone]
www.edgelighting.com
[email protected]
1: Rotate the Cody's head perpendicular to the arm making
sure the arm is completely inserted into the head. Tighten
the M3 set screw on the swivel connector with the provided
1.5mm Allen wrench to secure the head in place.
SAVE THESE INSTRUCTIONS!
- This product is ETL listed for indoor location
- This product is wall mounted only.
- This instruction shows a typical installation.
IMPORTANT INFORMATION
A
1
B
3
4
ANCHOR
WALL
2
MOUNTING BRACKET
2: Hold the mounting bracket against the wall where Cody 6"
will be mounted. Level the mounting bracket and mark the
bracket holes on the wall.
3: Tap the anchors onto the marked points into the wall up to
the threaded portion with a hammer.
4: Screw the threaded portion of the anchors in with the a
Phillips screwdriver.
NOTE: The Cody 6" plug-in comes with 9' of cord and
plug-in power supply. Make sure there is a power outlet
near to where Cody 6" will be mounted.
HEAD
ARM
1.5MM ALLEN
WRENCH
M3 SET SCREW
SWIVEL
CONNECTOR
1
© 2015 Edge Lighting. All Rights Reserved.

RIDGED WIRE
1"
SMOOTH WIRE
8
9
CORD
C
ANCHOR
#8 SCREW
MOUNTING
BRACKET
5
5: Line up the mounting bracket holes with the anchors and
secure the fixture to the anchors with the two #8 screws
provided.
ARM
D
2MM ALLEN WRENCH
M4 SET
SCREW
6
6: To adjust the Cody height, loosen the two M4 set screws on
the mounting bracket with the provided 2mm Allen wrench.
Adjust the Cody by sliding it up or down. When the desired
height is achieved tighten the two M4 set screws with the
2mm Allen wrench.
MOUNTING
BRACKET
E7: Select the location on the cord where the switch will be
installed.
8: With a sharp knife cut about 1" in the cord web. Make sure
not to nick the insulation on either wire.
9: Cut the smooth wire in half.
F
NUT
SMOOTH
WIRE
RIDGED
WIRE
10: Loosen the screw on one side of the switch to remove the
nut from the other side. Separate the two halves from each
other.
11: Place the half of the switch without the wheel onto the cut
portion of the cord. The uncut ridged wire should pass
through the half where the cut wire will be blocked in the
middle. This will ensure the switch connectivity.
12: Replace the half with wheel onto the other half so that the
sharp prongs pierce the insulation of the cut wire.
13: Replace the nut and tighten the screw ensuring that both
halves are mated properly.
CORD WEB SHARP PRONG
2
10
12
11
WHEEL
13

G
3
H
NOTE: The Cody 6" contains 6 watt integrated LED lamps. These
lamps are rated for 50,000 hours.
15: Hang the frame cable in the mounting bracket slot.
MOUNTING BRACKET SLOT
IFIXTURE HEAD
16
14: Use the provided cable clips to secure the cord to the
wall, or use a cable cover (not provided)
CORD
CABLE CLIP
14
J
17: Plug the power supply into the 120 volt power outlet.
PLUG-IN
POWER SUPPLY
120 VOLT
POWER OUTLET
17
16: Rotate the fixture head to properly wash the picture with
light.
15
FRAME CABLE