Elation PowerSpot 575IE User manual

User Manual
Software Version 1.60 Revised 07/2005

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 2

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 3
Table of Contents
Introduction..........................................................................................................................5
Unpacking ......................................................................................................................5
Customer Support .......................................................................................................5
Discharge Lamp Precautions .......................................................................................6
Safety Instructions ............................................................................................................7
1Fixture Layout......................................................................................................................8
2Preparation and Installation ......................................................................................... 11
2.1 Mounting ..................................................................................................................... 11
2.1.1 Clamps............................................................................................................ 11
2.1.2 Mounting Plate................................................................................................ 12
2.2 Rigging the Power Spot 575IE™............................................................................ 12
2.3 Connections................................................................................................................ 13
2.3.1 Power Supply................................................................................................ 13
2.3.2 DMX-512 Pin Configuration.......................................................................... 13
2.4 DMX-512.................................................................................................................... 13
2.5 Data Cable Requirements........................................................................................ 13
2.6 Special Note............................................................................................................... 13
2.7 Line Termination ......................................................................................................... 13
2.8 MX Pin Conversion ................................................................................................... 13
2.9 Fuse Requirements ................................................................................................... 13
2.10 Transporting & Handling ............................................................................................ 13
3Menu Field .......................................................................................................................... 16
3.1 Setting the DMX - Address (D001)....................................................................... 18
3.2 Test Menu (TEST).................................................................................................... 18
3.3 Lamp On/Off (LAMP) .............................................................................................. 18
3.4 Reset (RESE).......................................................................................................... 18
3.5 Running Time (lamp/unit) (TIME)............................................................................. 18
3.6 Invert Pan Movement (RPAN)............................................................................... 19
3.7 Invert Tilt Movement (RTLT) ................................................................................... 19
3.8 DMX Mode ................................................................................................................ 19
3.9 Special Functions (SPEC) ...................................................................................... 19
3.9.1 Manual Drive (MANU) .................................................................................. 20
3.9.2 Lamp On (automatic) (LAAU) ...................................................................... 20
3.9.3 Lamp Off (via DMX)...................................................................................... 21
3.9.4 DMX Input (DLOF) ...................................................................................... 22
3.9.5 LED Display (DISP) .................................................................................... 21

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 4
3.9.6 Fixture Temperature (TEMP) ....................................................................... 22
3.9.7 Fan Control (FANS) .................................................................................... 22
3.9.8 Adjustments and Calibrations (ADJU) ...................................................... 23
3.9.9 Default Settings (DFSE) .............................................................................. 24
3.9.10Feedback (FEED) ........................................................................................ 24
3.9.11Fault Corrections (EFLD) ............................................................................ 24
3.10 Error and Information Messages............................................................................... 24
4Operating Modes.............................................................................................................. 25
4.1 Universal DMX Control ............................................................................................. 27
4.2 Stand Alone (Sound Active) .................................................................................... 27
4.3 Master-Slave.............................................................................................................. 28
5DMX Channel Selection (DMX Protocol)..................................................................... 29
6Lamp Change .................................................................................................................... 33
6.1 Safety Regulations .................................................................................................... 34
6.2 Realize the Lamp Change........................................................................................ 34
7Fuse Replacement........................................................................................................... 35
8Change a Gobo................................................................................................................. 37
8.1.1 Safety Regulations......................................................................................... 37
8.1.2 Realize the Gobo Change............................................................................ 37
9Maintenance and Cleaning the Power Spot 575IE™............................................ 39
9.1 Safety Regulations .................................................................................................... 39
9.2 Circumference and Interval........................................................................................ 39
9.3 Cleaning the Optical System.................................................................................... 40
10 Technical Specification.................................................................................................. 40
11 Warranty.............................................................................................................................. 41
12 Dimensions........................................................................................................................ 43
13 Index .................................................................................................................................... 44

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 5
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The Power Spot 575IE™, has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to operate
this unit. These instructions contain important information regarding safety during use and
maintenance.
UNPACKING: Thank you for purchasing the Power Spot 575IE™ by Elation Professional®.
Every Power Spot 575IE™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your unit for damage
and be sure all accessories necessary to operate the unit have arrived intact. In the event
damage has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting customer
support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to
provide set up help and to answer any question should you encounter problems during your
set up or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Forum: www.ElationLighting.com/forum/
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself, doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Power Spot 575IE™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping container.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 6
If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items
returned without a R.A. number clearly marked on the outside of the package will be refused
and returned at cutomers exspence. You may obtain a R.A. number by contacting customer
support at [phone].
DISCHARGE LAMP WARNING: This fixture is fitted with a discharge
lamp, which is highly susceptible to damage if improperly handled. Never
touch the lamp with your bare hands, as the oil from your hands will
shorten lamp life. Also, never move the fixture until the lamps have had
ample time to cool. Remember, lamps are not covered under warranty
conditions.
This fixture emits intense UV radiation, which is harmful to the eyes and skin. The intense
luminance of the lamp can cause severe damage to the retina. Never operate this fixture with
the protective covers removed, these covers have been specially designed to shield against
UV radiation.
Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the lamp
at all times.
Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp life
and intensity.
To achieve the intensity associated with discharge lamps, these lamps use a gas sealed in a
high-pressure environment to emit a brilliant output. Due to the high pressure involved with the
construction of the lamp, the lamp may explode during prolonged extensive use. This risk is
increased with age; added care is encouraged when dealing with older lamps. Thus, lamp
should always be replaced at the end of their recommended duty cycle. Extreme caution
should be used when operated this or any fixture fitted with a gas discharge lamp.
Never open this fixture while in use!
During the initial operation of this fixture, a light smoke or smell may emit from the interior of the
fixture. This is a normal process and is caused by excess paint in the interior of the casing
burning off from the heat associated with the lamp.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 7
Safety Instructions
The Power Spot 575IE™ is an extremely sophisticated piece of
electronic equipment. To guarantee a smooth operation, it is important to
follow the guidelines in this manual. The manufacturer of this device will
not accept responsibility for damages resulting from the misuse of this
fixture due to the disregard of the information printed in this manual.
1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow
about 6” (15cm) between this fixture and other devices or a wall to allow for proper
cooling.
2. Never touch the fixture during normal operation. This can cause severe personal injuries
and/or damage to the fixture.
3. Be sure to unplug the POWER SPOT 575IE™ from the power outlet before performing
any service related issues.
4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power before you
open the POWER SPOT 575IE™. To prevent personal injury, never touch the lamp if
you are not absolutely sure it has cooled.
5. Never look directly into the lamp beam. You risk injury to your retina, which may induce
blindness.
6. Be sure to track and record the lamp running time. The lamp should be changed at the end
of the specified lamp life, regardless of lamp output. You may also have to change the
lamp if it shows any deformations or damage. The same is with all glass components,
color filters, lenses and mirrors.
7. For safe operation, follow the Installation guide described in chapter two of this manual.
Operating the POWER SPOT 575IE™ without suited safety aids such as safety cables
or clamps can increase the risk of damage and/or personal injury.
8. Installation should only be performed by qualified and certified personal.
9. When mounting this fixture, use only the original rigging parts included with this fixture.
Any structural modification will void the original manufactures warranty and may increase
the risk of damage and/or personal injury.
10. To reduce the risk of fire or shock, do not expose this unit to rain or moisture.
11. Do not attempt to operate this fixture if the power cord is frayed or damaged.
Attention: Lasers of class 3R may
injure your retina after a short residence
time even without any optical
instrument. Avoid any direct ex-
posure of your eyes!

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 8
1. Fixture Layout
1. Lens Assembly
2. DMX Input Jack
3. DMX Output Jack
4. Microphone Sensitivity
Adjustment Knob
5. Firmware Connection
6. Internal Cooling Fan
7. Base
8. Retaining Arm
9. Lamp Fuse Holder
10. Electronics Fuse Holder
11. Powercon Connector
12. Power Switch
13. Carrying Handle
14. 4-Segment Menu Display
15. Mode Select Button
16. Enter Select Button
17. Down Select Button
18. Up Select Button
1
3
5
4
2
6
8
6
13
11
9
10
12
14
15
16
17
18
7

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 9
1. Lens Assembly -This high quality lens is a fully focusing. Focus the lens by
manually turning the lens in a clockwise or counter-clockwise direction until the desired
effect is achieved.
2. DMX Input Jack – This 3-Pin XLR jack is used to receive an incoming DMX signal.
3. DMX Output Jack – This 3-Pin XLR jack is used to send an outgoing DMX signal.
For best results this jack should be terminated if it is the last fixture in a DMX daisy-
chain (see termination on page 14).
4. Microphone Sensitivity Adjustment Knob – This knob is used to adjust the
frequency sensitivity of the internal microphone when operating in “audio” mode.
When the knob is turned counter-clockwise the unit is less sensitive to sound. When
the knob is turned clockwise the unit is more sensitive sound.
5. Firmware Connection –This connection is designed to be used solely by an
authorized technician to upgrade the operating software and to test the fixture.
6. Internal Cooling Fan – This fixture is equipped with two high-velocity variable
speed fans mounted in the base to aid in the cooling process. These fans are
designed to vary their velocity at different operating temperatures. When the fixture
reaches a predetermined internal operating temperature the fans function at high
speeds. The higher speeds provide better cooling associated with higher operating
temperatures during long use. When the fixture is operating at a lower temperature
the fans operate at low speed. Be sure to keep all vents clean, blocked cooling
vents can shorten lamp life and reduce the fixtures reliability. For more information on
the fan functions see page 23, section 3.9.7.
7. Base –The main base holds the majority of the electronics and logic boards. The
base also provides a means to securely mount the fixture to the floor or ceiling.
8. Retaining Arm – These arm hold the head in place and provide a means of tilt
movement. These arms also provide a conduit for all the electronics traveling from the
base to the head.
9. Lamp Fuse Holder –This housing holds a 8A/250V GMA fuse. Never defeat this
fuse, this fuse is designed to protect the lamp in the event of severer power
fluctuations. In the event of fuse failure, always be sure to replace this fuse with an
exact match unless otherwise instructed by an authorized Elation technician.
10.Electronics Fuse Holder –This housing holds a 1A/250V GMA fuse. Never
defeat this fuse, this fuse is designed to protect the electronics in the event of severer
power fluctuations. In the event of fuse failure, always be sure to replace this fuse
with an exact match unless otherwise instructed by an authorized Elation technician.
11.Powercon Connector –This power jack is designed to be used only with the
Neutrik Powercon adapter included with your fixture. This jack provides main power
to your fixture.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 10
12.Power Switch – The switch is used to control main power to fixture’s electronics.
13.Carrying Handle –The fixtures includes two built-in carrying handles. Be sure to
always handle the fixture by the built-in carrying handles. Never lift or carry the fixture
by the head or retaining arms as this could cause serious damage to the fixture and
void your manufactures warranty.
14.4-Segment Menu Display – This display details menu functions.
15.Mode Select Button –This button is used to access the fixture’s main system
menu and on-board programming functions.
16.Enter Select Button –This button is used to select and confirm a menu function
when working in the fixture’s operating system.
17.Down Select Button –This button is used to scroll backwards when navigating
through the system menu.
18.Up Select Button - This button is used to scroll forward when navigating through the
system menu.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 11
2. Preparation and Installation
2.1 Mounting
The POWER SPOT 575IE™ is fully operational in two different mounting positions,
hanging upside from a ceiling or set on a flat level surface. To avoid internal damage to
the unit, never mount the unit on its side as illustrated below. Be sure this fixture is
kept at least 0.5m away from any flammable materials (decoration etc.). Install a safety
cable that can hold at least 10 times the weight of the fixture. Never use the carrying
handles for secondary attachment.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE
0711-217 for proper installation in Europe
To ensure proper installation, only qualified staff should
attempt installation.
2.1.1 Clamps
The POWER SPOT 575IE™ has been designed to hold multiple clamps to the
bottom of the unit in several different orientations. Always use an appropriately
rated clamp to mount this unit to truss. Refer to the printed instructions on the
bottom of the fixture for proper clamp installation.
a) Cam lock System: This system allows a quick and efficient means to secure
a clamp to the unit. To attach a clamp to the unit, attach a clamp that is rated to
handle the weight of the unit to your cam lock. After a clamp has been

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 12
attached to the cam lock, attach the cam locks to the designated position on
the bottom of your unit. Lock the cam locks into position by turning the wing
nuts 90°.
90°
b) Be sure to always use two cam locks mounted to the bottom of unit to ensure
safe truss mounting (each two opposite threads max. M10x20).
4x M10x20mm
4x Camlock
2.2 Secure the POWER SPOT 575IE™
Regardless of the rigging option you choose for your POWER SPOT 575IE™
always be sure to secure your fixture with a safety cable. The fixture provides a built-in
rigging point for a safety cable on the underside of the fixture, be sure to use this point
and never secure a safety cable to a carrying handle.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 13
2.3 Connections
2.3.1 Power supply
Electronic ballast with:
90~260 Volts, 50~60 Hz,
Grounded contact type plug – Neutrik Powercon
Connected load 780W <=> 3.8A (blind current compensation).
NOTE: The universal power supply will accept any voltage source as detailed
above without any type of internal or user modifications.
2.3.2 DMX-512
3-Pin XLR Input/Output. [+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol
used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX controller
sends DMX data instructions from the controller to the fixture. DMX data is
sent out as serial data that travels from fixture to fixture via the DATA “IN” and
DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminals). DMX Linking: DMX is a language allowing all
makes and models of different manufactures to be linked together and
operate from a single controller, as long as all fixtures and the controller are
DMX compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The order in
which fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in
the middle. Therefore, the first fixture controlled by the controller could be the
last fixture in the chain. When a fixture is assigned a DMX address of 1, the
DMX controller knows to send DATA assigned to address 1 to that fixture, no
matter where it is located in the DMX chain.
2.4 Data C able (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The POWER SPOT 575IE™ can be controlled via DMX-512 protocol.
The POWER SPOT 575IE™ is a 16 channel DMX fixture. The DMX address is set
electronically using the controls on the side panel of the fixture. Your fixture and your
DMX controller require a standard 3-pin XLR connector for data input and data output
(Figure Below). If you are making your own cables, be sure to use standard two

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 14
conductor shielded cable (This cable may be purchased at almost all professional
sound and lighting stores). Your cables should be made with a male and female XLR
connector on either end of the cable. Also remember that DMX cable must b e daisy
chained and can not be split.
2.5 Notice: Be sure to follow the above figure when making your own cables. Do not
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor
to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behavior.
2.6 Special Note: Line Termination.When longer runs of cable are used, you
may need to use a terminator on the last fixture to avoid erratic behavior. A terminator is
a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male
XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR
connector of the last fixture in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
2.7 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be
implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors
in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at
most electric stores. The chart below details a proper cable conversion.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 15
2.8 Fuse Requirements
The POWER SPOT 575IE electronic and lamp systems are protected by two GMA
(5x20mm) external fuses:
Lamp: 250V/8A
Electronics: 250V/1A
The fuse requirements are clearly printed on the side of the fixture.
WARNING:
•Always disconnect main power before changing the fuse!
•Always replace with the exact same type fuse unless otherwise
specified by an authorized Elation®service technician. Replacing with
anything other than the specified fuse can severely damage your fixture
and will void your manufactures warranty.
2.9 Transportation and Handling
The POWER SPOT 575IE ™ comes with two carrying handles built into the base.
Always transport the fixture by these handles. Never lift or carry the POWER SPOT
575IE™ by the yoke (head assembly) this can seriously damage the unit.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 16
3. Fixture Menu
The control panel located on the side of the fixture allows you to access
the main menu and make all necessary adjustments to the POWER
SPOT 575IE™. During normal operation, tapping the “MODE” key
once will access the fixture’s main menu. Once in the main menu you
can navigate through the different functions and access the sub-menus
with the Up and Down buttons. Once you reach a field that requires
adjusting, tap the ENTER button to activate that field and use the UP
and Down button to adjust the field. Tapping the Enter button once
more will confirm your setting. Once a setting is saved the LED will
briefly readout OK to confirm a new setting has been made and locked
into memory. You may exit the main menu at any time without making
any adjustments by tapping the MODE button.
MODEENTER
UP DOWN
MODE ENTER UPDOWN
UPMODE ENTER DOWN
Display
Level 1
Level 2
Level 3
Remark
D001
Define the DMX start address
TEST
Test program of all functions
AUDI
ASLW
Self-running audio program (slow)
AFST
Self-running audio program (fast)
MSTR
Master for the audio program
SVPT
Basic position for the audio program
SIZE
Size for the audio program (NORM-BIG-MIDL-SMAL)
LAMP
Switch on/of the lamp direct at the Power Spot 575IE
RESE
Reset
TIME
POWR
Running time of the fixture (non destructible)
LA1
Running time of the lamp (erasable)
LA2
Running time of the lamp (non destructible)
RPAN
Reverse Pan-direction
RTLT
Reverse Tilt-direction
SPEC
MANU
Manual control of all device functions
LAAU
Automatic lamp start
DLOF
Switch off lamp via DMX
DMXI
Reed out actual DMX-values
DISP
D ON
Display On/Off
REV
Flip display readout
TEMP
Displays internal temperature
FANS
HIGH
Maximum cooling fan velocity
REG
Automatic cooling fan control
LOOF
Low cooling fan speed lamp off
LOHI
Low cooling fan speed automatic
ADJU
CODE
xxxx
These menu settings are reserved for authorized
technician use only and are protected by a user code.
COLO
Calibration of the color wheel
GOB1
Calibration of gobo wheel 1
GOB2
Calibration of gobo wheel 2
SHTR
Calibration of the shutter
PRIS
Calibration of the prism wheel
IRIS
Calibration of the IRIS
POFS
Calibration of the pan-offset
TOFS
Calibration of the tilt-offset
clre
Clears internal memory (technician only)
ares
Adjust Reset (wheels static after reset)
DOWN - UP 
VTIL
Software version, tilt pc-board

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 17
VTR1
Software version, driver board 1
VTR2
Software version, driver board 2
VTR3
Software version, driver board 3
DFSE
Call on the default function values
FEED
Pan/Tilt feedback (error correction) On/Off
EFLG
Correction of faults
3.1 Setting/Changing the DMX Address
After applying power to the POWER SPOT 575IE™ the LED will display the fixture’s
current DMX address immediately after the reset sequence. If the fixture is not receiving
a DMX signal the display will flash continuously.
D001
To set or adjust a DMX address, please follow the procedure below:
1. Switch on the POWER SPOT 575IE™ and wait for the fixture reset process to
finished ('RESE'will flash in the LED while fixture is in reset mode).
2. Press the Mode button to access the main menu. Toggle through the menu by
pressing the Up and Down buttons until the display shows D001. Tap the enter
button to make changes to the address, the current three digit address will
immediately begin to flash.
3. While the current three-digit address is flashing, use the Up and Down buttons to
select adjust the address. Lock your new address into the unit’s memory by pressing
the Enter button. After the new address has been successfully stored into the
fixture’s memory the LED will briefly readout OK.
The DMX address is non-destructible and will remain in the fixture’s memory even when
the power has been switched off. Memory is backed-up and retained by an internal
power source with a five year shelf life.
3.2 Test Program
Test
The Test Program engages the fixture’s internal test mode. This function runs a
complete test procedure of all functions. Press Enter to launch the self-test or the Mode
button to cancel and return to the main menu.

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 18
3.3 The Audio Program
Audi
The Audio menu allows you to run a stand-alone audio program. This program can run
either fast (AFST) or slow (Aslw); Fast (AFST): When running in “fast” mode every
sound impulse will trigger a new step. (Aslw): When running in You may run several
fixtures together at once to achieve a synchronized light show running to sound in a
Master/Slave configuration. To run in a Master/Slave.
Additionally you can choose a basic position for this audio chaser. Use either the internal
manual mode or an external DMX controller to set the desired Pan/Tilt position. Confirm
this setting in the SVPT menu by pressing the Enter button.
You can also set the size of the audio chaser in the SIZE menu. You have the choice
between: NORM (no basic position has to bee chosen), 'BIG', 'MIDL' and 'SMAL').
If you want to run several units in a Master/Slave system be sure designate your first unit
in the chain as the master. All others must be "Slave" Master = OFF. Notice: The Audio
function is only working if no DMX is connected.
3.4 Lamp On/Off
LAMP
This function allows you to manually control the lamp operation. Access the lamp function
in the main menu and use the use the Up and Down buttons to toggle between lamp
On and lamp Off. Press the Enter button to confirm the operation or the Mode button
to cancel and return to the main menu. (The lamp OFF command will only functions if and
when the shutter is closed at the same time).
3.5 Reset
RESE

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 19
This function will rest and return all motors to the home position. Access the reset function in
the main menu and press the Enter button to engage the reset function (RST will readout in
the display).
3.6 Running Time (lamp/unit)
TIME
This menu function will read out three different fixture running times.
POWR
Fixture running time (non destructible). Total running time logged by the unit.
LA 1
Lamp running time (erasable). Press and hold down the Up and Down
buttons together for three seconds to reset this function.
LA 2
Lamp running time (non destructible). Total lamp hours logged by the unit
3.7 Invert Pan Movement
RPAN
This function allows you to invert all pan movements. Use the Up and Down buttons to
turn this function On and Off. Press the Enter button to accept the change or the Mode
button to cancel and return to the main menu.
3.8 Invert Tilt Movement
RTLT
This function allows you to invert all tilt movements. Use the Up and Down buttons to
turn this function On and Off. Press the Enter button to accept the change or the Mode
button to cancel and return to the main menu.
3.9 Special Functions
SPEC
This menu option accesses several special features and function of the POWER SPOT
575IE™. The SPEC sub-menu consists of several sub-menus. Navigation details of the

Power Spot 575IE™
©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 20
special functions and their sub-menus are as followed:
3.9.1 Manual Drive
MANU
This feature allows you to drive all the unit’s functions manually for use in an
environment that requires a static position (no movements), determining focus
points, or testing. Use the Up and Down buttons to select the function you wish
to adjust, then use the Enter button to accept your selection. Now adjust the
values with the Up and Down buttons and use the Enter button to lock in your
value. Use the Mode button to cancel at any time.
Function
Value
Remark
PAN
000 - 255
Pan Position
TILT
000 - 255
Tilt Position
COLO
000 - 255
Color wheel
GOB1
000 - 255
Gobo wheel 1
GROT
000 - 255
Gobo rotation
GOB2
000 - 255
Gobo wheel 2
shut
000 - 255
Shutter/Strobe functions ~ Lamp will strike
at a channel value of 255 if the dimmer
channel is at a value of 255 (Open)
dimr
000 - 255
Dimmer
FOCU
000 - 255
Focus
Pris
000 - 255
Prism: (000-127)/Stop/Prism rotation
IRIS
000 - 255
Iris
Spec
000 - 255
Lamp Off, Reset, Laser…,
3.9.2 Lamp On (automatic lamp strike)
LAAU
This function automatically strikes lamp when main power is turned on. If you
would prefer to strike the lamp through a DMX controller you must turn this function
off. To toggle between “OFF” and “ON” use the Up and Down buttons. Use the
Enter button to confirm your setting.