Edimax ES-3116P User manual

0

1
Copyright©by Edimax Technology Co, LTD. all rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of this company
This company makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this company, its distributor,
or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in the contents hereof
without obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from those
shown in this Manual. The software and specifications are subject to change without notice.
Please visit our web site www.edimax.com for the update. All rights reserved including all brand
and product names mentioned in this manual are trademarks and/or registered trademarks of their
respective holders.
F
Fe ed de er ra al l C Co om mm mu un ni ic ca at ti io on n C Co om mm mi is ss si io on n I In nt te er rf fe er re en nc ce e S St ta at te em me en nt t
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter.This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the authority to operate equipment.
CE Mark Warning.
This is a Class B product. In a domestic environment, this product may cause radio interface, in
which case the user may be required to take adequate measures.

2
Thank you for purchasing Edimax ES-3116P Fast Ethernet switch. This 16 ports high
cost-efficiency switch complies with 10/100-Base-TX standards is the best choice for
Small office / Home office users. Easy install procedures allows any computer users to
setup a network environment in very short time .
Product Package
This package contains the following components:
One Fast Ethernet Switch
Quick Installation Guide
12V 1A Power Adapter
Accessaries kit
If any item is missing or damaged, please contact your local resellers for service.
Feature
•Complies with the IEEE 802.3 , IEEE 802.3u standards.
•Provides Store and Forward architecture, full wire speed filtering and forwarding rates.
•Supports Auto-MDI/MDI-X, full/half duplex modes and auto-negotiation.
•Supports flow control: back pressure for half-duplex, IEEE 802.3x for full-duplex mode.
•Automatic source address learning and aging, extensive front-panel diagnostic LEDs.
Front Panel & Connectors
ES-3116P
Fast Ethernet Switch LED Panel
LED Color Status Description
Lit Power is supplied
PWR
(Power) Green Off No power
Lit A valid link is established
Flash Data packets received
LNK/ACT
(Link/Activity) Green Off No link is established
Lit This port run at 100Mbps
SPEED
(10/100M) Yellow Off This port run at 10Mbps

3
1.Operating Environment
This switching hub must be installed and operated within the limits of specified operating
temperature (32-131°F) and humidity (10~95% Non-condensing).
zDo not place objects on top of the unit.
zDo not obstruct any vents at the sides of the unit.
zDo not position the unit near any heating source such as heater, radiator, or direct
exposure to sun.
Prevent entering of water and moisture into the unit. If necessary, use dehumidifier to
reduce humidity.
2.Connecting to network devices
The RJ-45 ports on the switch support Auto-MDI/MDI-X function which allows using
straight-through or cross-over type cables to connect this switch to workstation or hub.
Connect one end of the network cable to the RJ-45 port on the rear panel, and connect
the other end of the network cable to the RJ-45 port on the network device. Follow the
same procedure to connect all the RJ-45 ports of the switch.
The UTP network cables must comply with EIA/TIA 568 specifications and Category 5
standard for 100Mbps data transmission. Maximum length: using UTP cable, between
the switch and connected device is 100 meters (300ft).
Once the network cable is connected to both ends and the attached network device is
powered on, the green LNK/ACT LED should be lit.

4
3.Connecting the power
Connect the power adapter to the power connector on the rear panel of the unit; the
green Power LED on the front panel should be lit.
Trouble Shooting
1.Power LED is not lit
zCheck if the power cord is properly connected to the external power adapter and the
power outlet. Make sure the DC power jack is firmly plugged into the power socket of
the switch.
2.Link/Activity is not lit when connect to 100Mbps device
zCheck the power switch of the network device attached to the switch; make sure it is
turned ON.
zCheck the network cable; make sure it is properly connected to the switch and the
network device.
zCheck the network cable; make sure the UTP cables comply with EIA/TIA 568 and
Category 5 specification.
[!] Contact your dealer if problem persist.

5