Edimax nLite 3G-6200N User manual

лчиттничюнльтцию.
глтчн.Бзвыдны
www.sotmarket.ru
дбняинфмциятв,
тзывы,бзыиы
Инструкция
Edimax 3G-6200N
Перейти в карточку товара
8 800 775 98 98

1
Copyright©by Edimax Technology Co, LTD. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical , chemical, manual or otherwise, without the
prior written permission of this company.
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
Notice according to GNU/GPL-Version 2
This product includes software that is subject to the GNU/GPL-Version 2. You find
the text of the license on the product cd/dvd. The program is free software and
distributed without any warranty of the author. We offer, valid for at least three
years, to give you, for a charge no more than the costs of physically performing
source distribution, a complete machine-readable copy of the corresponding
source code. Please contact Edimax at: Edimax Technology co., Ltd, NO. 3,
Wu-Chuan 3rd RD Wu-Ku-Industrial Park, Taipei Hsien, Taiwan. R.O.C., TEL :
[phone], FAX : [phone], [email protected]
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about
this product, please refer to the User's Manual on the CD-ROM.
 Software and specifications subject to change without notice. Please visit our web
site for the update.
All rights reserved. Trademarks or registered trademarks are the property of their
respective holders

2
Introduction.................................................................................................................4
Chapter 1..................................................................................................................18
1.1 Cable Modem......................................................................................................30
1.2 Fixed-IP xDSL.....................................................................................................31
1.3 PPPoE ................................................................................................................32
1.4 PPTP ..................................................................................................................34
1.5 L2TP ...................................................................................................................36
1.6 Telstra Big Pond..................................................................................................38
Chapter 2..................................................................................................................40
2.1 System................................................................................................................42
2.1.1 Time Zone........................................................................................................43
2.1.2 Password Settings ...........................................................................................43
2.1.3 Remote Management ......................................................................................45
2.2 3G/3.5G ..............................................................................................................47
( A ) Plug and play, no setup procedure required...............................................47
( B ) PIN code or user name / password required:.............................................48
2.3 WAN....................................................................................................................48
2.3.1 Dynamic IP.......................................................................................................49
2.3.2 Static IPAddress..............................................................................................50
2.3.3 PPPoE (PPP over Ethernet) ............................................................................50
2.3.4 PPTP ...............................................................................................................50
2.3.5 L2TP ................................................................................................................50
2.3.6 Telstra Big Pond...............................................................................................50
2.3.7 DNS .................................................................................................................51
2.3.8 DDNS...............................................................................................................51
2.4 LAN.....................................................................................................................53
2.5 Wireless..............................................................................................................55
2.5.1 Basic Settings..................................................................................................56
2.5.2 Advanced Settings ...........................................................................................58
2.5.3 Security............................................................................................................60
2.5.3.1 WEP only ......................................................................................................60
2.5.3.2 802.1x only....................................................................................................62
2.5.3.3 802.1x WEP Static key..................................................................................63
2.5.3.4 WPA Pre-shared key.....................................................................................64

3
2.5.3.5 WPA Radius..................................................................................................65
2.5.4 Access Control.................................................................................................65
2.6 QoS.....................................................................................................................69
2.7 NAT.....................................................................................................................72
2.7.1 Port Forwarding ...............................................................................................74
2.7.2 Virtual Server ...................................................................................................76
2.7.3 Special Applications .........................................................................................78
2.7.4 UPnP Settings..................................................................................................81
2.7.5 ALG Settings....................................................................................................82
2.7.6 Static Routing...................................................................................................83
2.8 Firewall................................................................................................................85
2.8.1 Access Control.................................................................................................86
2.8.2 URL Blocking ...................................................................................................86
2.8.3 DoS (Denial of Service)....................................................................................93
2.8.4 DMZ.................................................................................................................94
Chapter 3..................................................................................................................95
3.1 Status and Information........................................................................................96
3.2 Device Status......................................................................................................98
3.3 System Log.........................................................................................................99
3.4 Security Log......................................................................................................100
3.5 Active DHCP Client...........................................................................................101
3.6 Statistics............................................................................................................102
Chapter 4................................................................................................................103
4.1 Configuration Tools ...........................................................................................103
4.2 Firmware Upgrade............................................................................................104
4.3 Reset ................................................................................................................105
Appendix A..............................................................................................................107
Glossary..................................................................................................................109

4
Introduction
Thank you for purchasing Edimax 3G-6200n nLite wireless 3G broadband
router! This high cost-efficiency router is the best choice for Mobile / Small
office / Home office users, all computers and network devices can share a
single wireless 3G modem or xDSL / cable** modem internet connection at
high speed. Easy install procedures allows any computer users to setup a
network environment in very short time - within minutes, even inexperienced.
When the number of your computers and network-enabled devices grow, you
can also expand the number of network slot by simple attach a hub or switch,
to extend the scope of your network!
You can configure the router by running the Setup Wizard in the CD-ROM
provided in the package. The wizard provides quick setup for wireless
3G/3.5G Internet connection, Ethernet WAN Internet connection, SSID,
wireless security, firmware upgrade and changing router’s password. When
you start the Setup Wizard, you will get the following Welcome screen. Please
choose the language to start with and follow the easy steps in the Wizard. No
instruction for the Setup Wizard is given here.

If you lost the CD-ROM or you prefer the traditional web setup, please follow
the procedures in Manual to configure the router.
Note 1: Only one Internet connection (wireless 3G or xDSL/Cable) can be
used at the same time.
Note 2: To prevent the compatibility problem between 3G USB Modem cad
and 3G router, it is recommended that you upgrade the latest firmware
of 3G router from Edimax website http://www.edimax.com .

5
Features
- Provides IEEE 802.11g/b wireless LAN access point
- Compatible with IEEE 802.11n standard with 150Mbps data rate
- High Internet access throughput
- Allow multiple users to share a single Internet connection
- Supports up to 253 network client users
- Provides one USB port for 3G wireless connection
- Internet Access via 3G modem or Cable or xDSL modem
- Access Servers on your LAN from the Public Network
- Equipped with four LAN ports (10/100M) and one WAN port (10/100M)
- Support DHCP (Server/Client) for easy setup
- Support advance features such as: special applications, DMZ, virtual
server, access control, firewall
- Allow you to monitor the router’s status such as: DHCP Client Log,
System Log, Security Log and Device/Connection Status
- Easy to use Web-based GUI for configuration and management
- Remote Management allows configuration and upgrades from a
remote site (over the Internet)
Minimum Requirements
- One External xDSL (ADSL) or Cable modem with an Ethernet port
(RJ-45)
- Network Interface Card (NIC) for each Personal Computer (PC)
- Computer with a Web-Browser (Internet Explorer 5.0 or higher /
Netscape Navigator 7.2 or higher)
Package Contents
- One Wireless 3G broadband router
- One Quick Installation Guide
- One CD-ROM (Wizard, Multi-languages QIG and User Manual)
- One Power Adapter
- Ethernet Cable
- Holding base
- Accessories
Note
The WAN “idle timeout” auto-disconnect function may not work due to
abnormal activities of some network application software, computer
virus or hacker attacks from the Internet. For example, some software

6
sends network packets to the Internet in the background, even when
you are not using the Internet. So please turn off your computer when
you are not using it. This function also may not work with some ISP. So
please make sure this function can work properly when you use this
function in the first time, especially your ISP charge you by access time.
Back Panel
The diagram (fig1.0) below shows the broadband router’s back panel.
The router’s back panel is divided into four sections, LAN, WAN, USB,
and Reset:
Figure 1.0
1) Local Area Network (LAN)
The Broadband router’s 4 LAN ports are where you connect your LAN’s
PCs, hubs / switches etc.
2) Wide Area Network (WAN)
The WAN port connected to your xDSL or Cable modem which linked to
the Internet.
3) USB
The USB port allow you to share internet via 3G USB modem card.
4) WPS / Reset button
You can press the button 2~4 seconds to enable WPS for wireless
security.
When you experience some problem on using this router, or you forgot
your password, you can press the reset button for longer than 20
seconds and the router will reset itself to the factory default settings
(warning: your original configurations will be replaced with the factory
default settings)
5) Wireless on/off
You can enable/disable WiFi wireless signal via switch button.

7
Front Panel
On the router’s front panel there are LEDs, which shows the status of
this router. Below is the list of each LED and its description.
Figure 1.1
LED Light
Status Description
ON Router is powered on
WAN
LNK/ACT
ON WAN is connected
Off WAN is unconnected
Flashing WAN port is sending / receiving data
LAN
LNK/ACT
(Port 1-4)
ON LAN port is connected
Off LAN port is unconnected
Flashing LAN port is sending / receiving data
3G
ON 3G USB modem is connected
Off 3G USB modem is not connected
Flashing 3G USB modem card is sending / receiving data
ON Wireless LAN has been activated
Off Wireless LAN is disabled
Flashing Wireless LAN is sending / receiving data

8
Setup Diagram
(
(A A) ) 3 3G G/ /3 3. .5 5G G M Mo od de em m c ca ar rd d i in ns st ta al ll la at ti io on n: :
If you have 3G/3.5G modem card and SIM card, please follow the following
instructions to establish connection
1. Connect power adapter to 3G-6200n
2. Connect another Ethernet cable from the any LAN ports (1~4) on router to
the
Ethernet socket on the PC
3. Insert SIM card into 3G/3.5G modem card, and connect the modem card
with one of USB port of 3G-6200n. The corresponding USB LED indicator
on 3G-6200n will light.

9
(
(B B) ) C Ca ab bl li in ng g i in ns st ta al ll la at ti io on n: :
If you can also access Internet by xDSL/Cable modem, please follow the
following instructions:
1. Connect the Ethernet cable from the router’s WAN port to the LAN port of
the
modem.
2. Connect another Ethernet cable from the any LAN ports (1~4) on router to
the
Ethernet socket on the PC.
3. Check to make sure the router’s LINK LED is lit; to confirm the cable
connections are made correctly.

10
Getting started
This is a step-by-step instruction on how to start using the router and
get connected to the Internet.
1) Setup your network as shown in the setup diagram above (fig 1.2).
2) You will need to set your LAN PC clients so that it can obtain an IP
address automatically. All LAN clients require an IP address. Just like
the mailing address in real world, it allows LAN clients to find one
another. (If you already configured your PC to obtain an IP automatically,
please jump to step 3, page 11)
Configure your PC to obtain an IP address automatically
Broadband router’s DHCP function is switched on by default; this
means that you can obtain an IP address automatically once you’ve
configured your PC to obtain an IP address automatically. This section
will show you how to configure your PC’s so that it can obtain an IP
address automatically for either Windows 95/98/Me, 2000 or NT
operating systems. For other operating systems (Macintosh, Sun, etc.),
follow the manufacturer’s instructions. The following is a step-by-step
illustration on how to configure your PC to obtain an IP address
automatically for:
2a) Windows 95/98/Me
2b) Windows XP
2c) Windows 2000, and
2d) Windows NT.
2a) Windows 95/98/Me
1.Click the Start button and select Settings, then click Control Panel.
The Control Panel window will appear.
2.Double-click Network icon. The Network window will appear.
3.Check your list of Network Components. If TCP/IP is not installed,
click the Add button to install it; if TCP/IP is installed, jump to step 6.
4.In the Network Component Type dialog box, select Protocol and click
Add button.
5.In the Select Network Protocol dialog box, select Microsoft and
TCP/IP and then click the OK button to start installing the TCP/IP
protocol. You may need your Windows installation CD to complete the
installation.
6.After installing TCP/IP, go back to the Network dialog box. Select
TCP/IP from the list of Network Components and then click the
Properties button.
7.Check each of the tabs and verify the following settings:

11
•Gateway:All fields are blank.
•DNS Configuration: Select Disable DNS.
•WINS Configuration: Select Disable WINS Resolution.
•IP Address: Select Obtain IP address automatically.
8. Reboot the PC. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router is the only DHCP
server on your LAN.
Once you’ve configured your PC to obtain an IP address
automatically, please proceed to Step 3
2b) Windows XP
1.Click the Start button and select Settings, then click Network
Connections. The Network Connections window will appear.
2.Double-click Local Area Connection icon. The Local Area Connection
window will appear.
3.Check your list of Network Components. You should see Internet
Protocol [TCP/IP] on your list. Select it and click the Properties button.
4.In the Internet Protocol (TCP/IP) Properties window, select Obtain an
IP address automatically and Obtain DNS server address
automatically as shown on the following screen.

12
5.Click OK to confirm the setting. Your PC will now obtain an IP address
automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router is the only DHCP
server on your LAN.
Once you’ve configured your PC to obtain an IP address
automatically, please proceed to Step 3
2c) Windows 2000
1.Click the Start button and select Settings, then click Control Panel.
The Control Panel window will appear.
2.Double-click Network and Dial-up Connections icon. In the Network
and Dial-up Connection window, double-click Local Area Connection
icon. The Local Area Connection window will appear.
3.In the Local Area Connection window, click the Properties button.
4.Check your list of Network Components. You should see Internet
Protocol [TCP/IP] on your list. Select it and click the Properties button.
5.In the Internet Protocol (TCP/IP) Properties window, select Obtain an
IP address automatically and Obtain DNS server address
automatically as shown on the following screen.

13
6.Click OK to confirm the setting. Your PC will now obtain an IP address
automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router is the only DHCP
server on your LAN.
Once you’ve configured your PC to obtain an IP address
automatically, please proceed to Step 3
.
2d) Windows NT
1.Click the Start button and select Settings, then click Control Panel.
The Control Panel window will appear.
2.Double-click Network icon. The Network window will appear. Select
the Protocol tab from the Network window.
3.Check if the TCP/IP Protocol is on your list of Network Protocols. If
TCP/IP is not installed, click the Add button to install it now. If TCP/IP
is installed, go to step 5.
4.In the Select Network Protocol window, select the TCP/IP Protocol
and click the Ok button to start installing the TCP/IP protocol. You may
need your Windows CD to complete the installation.

14
5.After you install TCP/IP, go back to the Network window. Select
TCP/IP from the list of Network Protocols and then click the Properties
button.
6.Check each of the tabs and verify the following settings:
•IP Address: Select Obtain an IP address from a DHCP server.
•DNS: Make all fields blank.
•WINS: Make all fields blank.
•Routing: Make all fields blank.
7.Click OK to confirm the setting. Your PC will now obtain an IP address
automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router is the only DHCP
server on your LAN.
Once you’ve configured your PC to obtain an IP address
automatically, please proceed to Step 3
3) Once you have configured your PCs to obtain an IP address
automatically, the router’s DHCP server will automatically give each of
your LAN clients an IP address. By default the Broadband Router’s
DHCP server is enabled so that you can obtain an IP address

15
automatically. To see if you have obtained an IP address, see Appendix
A.
Note: Please make sure that the Broadband router’s DHCP server is
the only DHCP server on your LAN. If there is another DHCP on your
network, then you’ll need to switch one of the DHCP servers off. (To
disable the Broadband router’s DHCP server see chapter 2 LAN Port)
4) Once your PC has obtained an IP address from your router, enter the
default IP address 192.168.2.1 (broadband router’s IP address) into
your PC’s web browser and press <enter>
5) The login screen below will appear. Enter the “User Name” and
“Password” and then click <OK> to login.
Note: By default the user name is “admin” and the password is “1234”.
For security reasons it is recommended that you change the
password as soon as possible (in General setup / system /
password, see chapter 2)
6) The HOME page screen below will appear. The Home Page is
divided into four sections, Quick Setup Wizard, General Setup,
Status Info and System Tools.

16
Quick Setup Wizard (Chapter 1)
Select your Internet connection type and setup the configurations
needed to connect to your Internet Service Provider (ISP).
General Setup (Chapter 2)
This section contains configurations for the Broadband router’s
advanced functions such as: address mapping, virtual server, access
control, hacker attack prevention, DMZ, special applications and other
functions to meet your needs.
Status Info (Chapter 3)
In this section you can see the Broadband router's system information,
Internet Connection, Device Status, System Log, Security Log and
DHCP client information.
System Tools (Chapter 4)
This section contains the broadband router’s tool sets - tools include
configuration, firmware upgrade and Reset. Configuration tools allow
you to backup (save), restore, or restore to factory default configuration
for your Broadband router. The firmware upgrade tool allows you to
upgrade your Broadband router's firmware. The RESET tool allows you
to reset your Broadband router.
7) Click on Quick Setup Wizard (see chapter 1) to start configuring
settings required by your ISP so that you can start accessing the
Internet. The other sections (General Setup, Status Information and

17
Tools) do not need to be configured unless you wish to implement /
monitor more advanced features/information.
Select the section (Quick Setup Wizard, General Setup, Status
Information and Tools) you wish to configure and proceed to the
corresponding chapter.

18
Chapter 1
Quick Setup
The Quick Setup section is designed to get you using the broadband
router as quickly as possible. In the Quick Setup you are required to fill
in only the information necessary to access the Internet. Once you click
on the Quick Setup Wizard in the HOME page, you should see the
screen below.
Step 1) Time Zone
The Time Zone allows your router to base its time on the settings
configured here, this will affect functions such as log entries and firewall
settings.
Parameter Description
Set Time Zone Select the time zone of the country you are living.
The router will set its time based on your selection
Time Server
Address You can manually assign time server address if the default time server dose not work
Daylight Savings
The router can also take Daylight savings into
account. If you wish to use this function, you must
check/tick the enable box to enable your daylight
saving configuration (below)
Times From Select the period in which you wish to start using
daylight saving
Times to Select the period in which you wish to stop using
daylight saving
Click on NEXT to proceed to the next page (step 2): Broadband Type.