Edis EA183 User manual

EA183 100W Portable outdoor speaker IPX4

1. Packing content
• Speaker x 1
• USB-C Charging Cable x 1
• User Manual x 1
2. Specifications
Input: DC 5V =-= 2A
Capacity: 10400mAh
Charging time: 6 hours
Playtime: Up to 12 hours (at 50% volume)
Bluetooth range: up to 20 m/66 ft
Weight: 4.3 kg/9.4 lbs
Size: 9.9 x 10.9 x 14.0 inches
Warranty: One-year limited
3. Buttons and Controls

4. LED Display Indicators
5. Connections

Tips
●Only one audio source can be played at a time. The priority order is USB > TFCARD > Bluetooth >
AUX IN.
●The speaker will auto-off after 30 minutes without audio input.
●To avoid sudden loud sound from the speaker, always turn down the volumeto minimum level on
the Bluetooth device and speaker(s) before playback
●Please feel free to contact support team at support if you needany assistance while using this
speaker.
6. Pairing PartyBoom with Your Device
1. Turn on the speaker, press to enter into Bluetooth pairing.
2. Turn on Bluetooth on your device, and select PartyBoom in theBluetooth list.
3. Once paired, will be steady white with a prompt tone.
●When the speaker connects with two devices at the same time viaBluetooth tracks plaved from the
last connected device.
7. True Wireless Stereo Pairing
1. Turn on the two speakers and long press on both simultaneously.
2. The speakers will enter stereo pairing mode, flashes white.
3. Once paired, the LED display of primary speaker will light in "A", and thesecondary speaker will
light in "B”
4. Turn on Bluetooth on your device and select PartyBoom.
5. Once paired, on the LED display will light in white.
●In TWS mode, if you want to play via PartySync mode, press and hold toexist TWS mode first.
●lf there are two devices connected to the speaker, long press to disconnectthe playing one
and enter TWS pairing mode.
●In TWS mode, press on both speakers if you want to active the Extra Bass.
8. PartySync Mode
1. Turn on one speaker and get it paired with your device. Then long press to enter the PartySync
mode. The speaker will be the primary speaker andlight in “A” on the LED display.
2. Turn on the other speaker(s) and long press to enter the PartySyncmode. The speaker(s)
will be the secondary speaker(s) and light in “B” on theLED display.
●In PartySync mode, if you want to play via TWS mode, press and hold to exist PartySync
mode first.
●lf there are two devices connected to the speaker, long press todisconnect the playing one
and enter TWS pairing mode.
●In PartySync mode, press on all speakers if you want to active theExtra Bass, and audio
control can only be adjusted on the primary speaker.

9. Warning
●Avoid dropping or hitting the speaker.
●Avoid exposing to extreme temperature.
●Avoid using the speaker near a microwave.
●Never disassemble or repair the speaker
●Never use any corrosive cleanser/oil to clean.
●Never leave the speaker in a car parked in the sun.
●Never attempt to charge the speaker while it is wet.
10. FCC Statement
This equipment has been tested and found to comply with the limits for a ClassB digital device,
pursuant to part 15 of the FCC Rules. These limits are designedto provide reasonable protection
against harmful interference in a residentiainstallation. This equipment generates, uses and can
radiate radio frequencyenergy and, if not installed and used in accordance with the instructions,
maycause harmful interference to radio communications. However, there is noguarantee that
interference will not occur in a particular installation. If thisequipment does cause harmful
interference to radio or television receptionwhich can be determined by turning the equipment off
and on, the user isencouraged to try to correct the interference by one or more of the
followingmeasures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver. Connect the equipment into an outlet
on a circuit different from that to whichthe receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help
●Caution: Any changes or modifications to this device not explicitly approved bymanufacturer could
void your authority to operate this equipment.This devicecomplies with part 15 of the FCC Rules.
Operation is subject to the followingtwo conditions:
(1) This device may not cause harmful interference, and (2) this device mustaccept any interference
received, including interference that may causeundesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.