Edsal TRK-361860W4 User manual

Model Numbers & Sizes
TRK-361860W4 (36”w x 18”d x 60”h x 4 levels)
TRK-482478W5 (48”w x 24”d x 78”h x 5 levels)
TRK-602478W5 (60”w x 24”d x 78”h x 5 levels)
Edsal Tri-Rack Heavy Duty Storage Unit
Rubber Mallet (preferred) or
Hammer (protect surface with
cloth or wood block)
Contents
Description Quantity Part Number Size
A: beam
8
10
10
TBE36BLK
TBE48BLK
TBE60BLK
36”
48”
60”
B: brace 8
10
TBE18BLK
TBE24BLK
18”
24”
C: post 8
8
UPT30BLK (60”)
UPT39BLK (78”)
30”
39”
D: shelf
4
5
5
RWD1836SF
RWD2448SF
RWD2460SF
18” x 36”
24” x 48”
24” x 60”
E: coupler 4 CPIDSPBLK - - -
F: post cap 4 RLPC - - -
Components
A: beam (long)
B: brace (short)
C: post
D: wire shelf
E: coupler
F: post cap
General Instructions
Assembly of this unit is done by fitting the rivets of the
beams and braces into the slots of the posts.
A rubber mallet should be used on the ledge of the
beams and braces to properly seat the rivets.
The wire deck will rest on the ledge surface of the
beam or brace depending upon the orientation of the
shelf level.
A rivet should engage and fit firmly into the tapered
slot of the post. This engagement is into a tapered slot
and will apply resistance as it engages. A visual in-
spection should be made to show that the rivet is prop-
erly engaged in the slot.
A rubber mallet is the recommended tool. If a hammer
is used care should be taken to protect the beam or
brace surface to avoid damage by using a protective
cloth or block of wood. Tap gently to assure that all
rivets are straight and engaged. After assembly re-
check each beam and brace for engagement.
Refer to “Shelf Position Chart” for ideal shelf spacing.
Assembly Options
This unit can be assembled by positioning the beams
and braces in one of two different orientations and
combinations: beams and braces facing upwards or
beams and braces facing downwards. Each shelf level
can then be used as utilized as a) standard flush shelf,
b) recessed tray, or c) combination of shelf and tray.
a) STANDARD FLUSH SHELF
b) RECESSSED TRAY
c) COMBINATION SHELF & TRAY
… create a flush front with raised sides
… create a four-sided tray
Tools Required

Assembly of this unit is done by fitting the rivets of the beams and braces into the slots of the posts.
The unit is assembled one level at a time. Each level is assembled with two beams (a) and two braces (b) connected to
the posts (c) and one wire shelf (d).
These units should be placed on a level surface. Failure to do so can result in a possible safety hazard.
This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included.
Do not use this unit for anything other than the manufacture’s intended purpose.
Do not stand on any part of the unit, or use it as a ladder. Use care when working with metal parts.
Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
Safety & Assembly Instructions
STEP 1 … check the orientation of the components
Check that each post is in the proper orientation. The post should
be positioned so that the tapered end of the hole is pointing down-
ward.
Check that the flat surface of the beam and brace ledge is facing in
the desired orientation.
STEP 2 … assemble bottom level
Assemble one brace to two lower posts skipping one hole from the
bottom of each post.
Place the rivets into the posts, and tap lightly to seat the rivets.
Repeat this with the other two lower posts and braces.
Assemble the beams into the two post and brace assemblies.
Place a wire deck on the ledge of the assembled beams and braces
with the flat side facing upwards.
STEP 3 … assemble next level
Connect another two braces and two beams to the posts for the next
level.
Check that each beam and brace is spaced equally.
Place a wire deck on the ledge of the assembled beams and braces
STEP 4 … connect posts with couplers
Position the couplers on the top edge of each bottom post.
Tap the couplers down to the mid-point of the coupler.
Position another post into the top half of the coupler and tap down
until the two posts connect fully into the coupler.
STEP 5 … assemble the remaining levels
Connect additional braces and beams to the posts for each level.
Check that each beam and brace is level and properly spaced.
Place a wire deck on the ledge of the assembled beams and braces
for each level.
STEP 6 … final assembly and check
Check each beam and brace connection to be sure that the rivets
are properly seated.
Place and fasten the post caps to the top of each post.
F: post cap
E: coupler
C: post
C: post
ALTERNATE HORIZONTAL CONFIGURATION ...
Shelf can be split into two units and used side by side. Cou-
plings are not required.
Beams and braces should be positioned in the top and bottom
two post holes of each section for stability.
vertical or
horizontal
configuration
Should you have any comments, missing parts, or problems with assembly of this unit
please contact our Quality Service and Manufacturing facility at
773-475-3137 or s[email protected]
To obtain replacement parts, please provide the following information :
- Model Number - Part Number & Description - Location Purchased - Date Purchased
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609
www.edsal.com
REV 2.2A
Made in the USA
patents pending