Effydesk Executive User manual

7
8
6
Instruction Manual
UL
600-1250mm
Segment Column 3
300 lbs
Height Range
Recommend Load 240 lbs
35mm/s
Crossbar
Control Box
Power Cable
Lifting Column
Foot
Extension Cord
Side Bracket
Keypad
Certification
Tool Required
4mm Allen Key
(included)
Tape Measure Screwdriver
＜
9
Cable Tray
Accessory List
Technical Data
Accessory List
Parts List
3mm Allen Key
(included)
If you have any issues with your product, please feel free to contact us via
[e-mail]
Thank you for your order!
We will help you resolve the issue as soon as possible.
[e-mail]
or
For more information, please visit
https://effydesk.ca/pages/how-to-assemble-your-height-adjustable-standing-desk
3
3
3
2
M6X12 M6X8
or
M5X20
M6X16
Dx10
Zip Ties
Rubber Pads
M4X12
Gx12
M6X16
Hx6
M4X10
Lx2
Kx2
Ix12 Jx16
M5X18
Hangers
Mending Plates
Ax12 Bx8 Cx19
Ex19 Fx2
M8X10

6
B
Separate the Crossbar ⑦ and you will find the Crossbar Rail inside.
Crossbar End
Crossbar Rail
Crossbar End
Insert one of the Crossbar Ends into the one of the Lifting Columns ③ and secure with screws.
Attach the Side Bracket ⑥ to one of the Lifting Columns.
12
Allen Key
4mm
Repeat the same step for the other Lifting Column.
STEP 1
Repeat the same step for the other Lifting Column.
STEP 2
STEP 3
Allen Key
4mm
Step 2 Assembly
Side Bracket
A
12
Allen Key
4mm

Allen Key
4mm
12
G
STEP 4
STEP 5
2
B
Allen Key
4mm
Slide the Crossbar two Rails back into the Crossbar Ends.
Please make sure to fit the slots as shown below.
Attach the Crossbar as shown.
STEP 6 Attach the Feet ④ to the bottom of the Lifting Columns.
B
Allen Key
4mm
2
G
Allen Key
4mm
12

X 2
Install the tabletop (Predrilled / Non-predrilled).
C19
19
E
Non-predrilled
Use the screws to tighten the Hangers onto
the Crossbar.
Note: The screws do not go through the Crossbar.
Hangers, Allen Key and screws are found in
a separate bag.
C
Hangers
X 2
H
L
Allen Key
3mm
Predrilled
STEP 7
STEP 9
19
X 2
I
Screwdriver
STEP 8
Place Mending Plates (J) over the seam
between the two tabletops and attach
them using Wood Screws (I).
X 2
J
Mending
Plates
H
Allen Key
3mm
2
L2
I
Allen Key
3mm
12
K2
Allen Key
4mm
C19
E
C19
19
Screwdriver

D
connect all the cables to the Control Box ①.
Allen Key
3mm
Note : Use Zip Ties (D) to secure cables under the table.
7
STEP 10
H
Firmly secure the Crossbar with Screws (A) and
Allen Key
4mm
16
A D
10
A
Attach the Cable Tray ⑧ to the Hangers with screws.
Power Port
Lifting Column Ports
Keypad Port
M 3M 2M 1 H S
STEP 11
M 3M 2M 1 H S
Keypad Port
Lifting Column Ports
Power Port
Slider for Control Box
J
Allen Key
4mm
16
D10
J
4