Egamaster Egatronik User manual

LASER DISTANCE DETECTOR

OPERATING INSTRUCTIONS

GUARANTEE........................ 13

COD.51269

PRODUCT INTRODUCTION

Code 51269, Handheld Laser Distance Meter, is specially designed for users. It is a meter with

high-precision and multi-function distance measurement. Code 51269 can measure distance,

area and volume, Pythagorean Laws can also be used in code 51269 to measure indiectly. Code

51269 which is light, easy to use and reliable to measure,can make sure your measurement more

accuracy, easier and faster.

Code 51269 can widely apply to Construction, Upholster, Property, Trafc, Fire-Fighting,

Gardens, Urban Planning, Water Mornitoring, Electric Power Overhaul,etc. As the replacer of

traditional measuring instrument (for example,measuring tape), code 51269 is your best choice.

UNPACKING INSPECTION

Unpack and check, if there is any damage or loss.

1. Mainframe one unit

2. User manual one copy

3. AAA battery(2×1.5V) one piece

4. Carrying case one unit

5. Mini screwdriver one piece

SAFETY INSTRUCTION

PERMITTED USE

- Measuring distances

- Computing functions, e. g. areas and volumes

- Indirect Measuring with Pythagorean Prohibited use

- Using the instrument without instruction

- Using outside the stated limits

- Deactivation of safety systems and removal of explanatory and hazard labels

- Opening of the equipment by using tools (screwdrivers, etc.), as far as not specically permitted

for certain cases

- Carrying out modication or conversion of the product

- Use of accessories from other manufacturers without the express approval of manufacturer.

- Deliberate or irresponsible behavior on scaffolding, when using ladders, when measuring near

machines which are running, or near parts of machines or installations which are unprotected

- Aiming directly into the sun or glare

- Deliberate dazzling of third parties; also in the dark Inadequate safeguards at the surveying site

(e.g. when measuring on roads, construction sites,etc.)

LASER CLASSIFICATION

The code 51269 produced a visible laser beam which emerges from the front of the instrument.

Laser Class II products:

Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is

normally afforded by aversion responses including the blink reex.

WARNING

Looking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous.

Precautions:

Do not look directly into the beam with optical aids.

CAUTION

Looking into the laser beam may be hazardous to the eyes.

Precautions:

Do not look into the laser beam. Make sure the laser is aimed above or below eye level.

METER STRUCTURE

Keypad

1. ON / MEAS (On/measuring) button

2. Area / volume button

3. Indirect measurement button

4. Continuous measurement button

5. Plus (+) button

6. Minus (-) button

7. Storage button

8. Reference level button

9. Illuminating button

10. Clear/off button

LCD Display

1 Laser active

2 Reference level (front)

3 Reference level (rear)

4 Reference level (End piece)

5 Continuous measurement

6 Instrument error warning

7,8,9,10,11

Variable measuring functions

Length measurement

Area measurement

Volume measurement

Indirect (2 times) measurement

Indirect (3 times ) measurement

12 Battery status

13 Historical memory, call up values

14 First value display line, minimum value

15 Second value display line, maximum value

16 Third value display line

17. Summary line for last measure or calculation result

SETTING AND OPERATION OF METER

Switching on and off

Switches on the instrument and laser.

Press this button longer to switch off the instrument..

The instrument switches off automatically after three minutes of inactivity.

CLEAR button

The last action is cancelled or the data display is cleared.

REFERENCE LEVEL SETTING

The default reference setting is from the rear of the instrument.

Press this button to take the selection from the front edge . A special beep sounds

whenever the reference setting is changed. After a re-startup the reference returns automatically to

the default setting (rear reference).

Press this button again to take the next selection from end piece edge.

Press this button , to set the rear reference again.

In a word, to select the reference level, push button repeatedly until the required reference

level is indicated in the display. Each time after switching on, the rear edge of the measuring tool is

preset as the reference level.

DISPLAY ILLUMINATION

Click illumination button of the display can be switched on or off, User can trigger the

function when he/she is in darkness situation. The value is clear viable on the LCD.

DISTANCE UNIT SETTING FOR INSTRUMENT

Click the button longer change the next type of unit, m, ft. in, ft/in then to continue click the

button for the next unit selection.

MEASURING

SINGLE DISTANCE MEASUREMENT

Press to activate the laser. Press again to trigger the distance

measurement. The measured value is displayed immediately.

Continuous Measurement & Max and Min Measurement The continuous measurement function

(tracking) is used for the transferring of measurements, e.g., from construction plans. In continuous

measurement mode, the measuring tool can be moved close to the target, whereby the measured

value is updated approx. every 0.5 seconds. The corresponding dynamically maximum and

minimum values are displayed in the rst and second line.

As an example, the user can move from a wall to the required distance, while the actual distance

can be read continuously. For continuous measurement, press button until the indicator

for continuous measurement appears in the display. And press it again or press to stop the

function.

The function is terminated after 5 minutes’ continuous measurement.

With this function, customers can measure the max and min distance from a certain point.

FUNCTIONS

ADDITION / SUBTRACTION DISTANCE MEASURING.

The next measurement is added to the previous one, then press the button , the second

measured value is shown and the result is shown automatically. The next measurement is

subtracted from the previous one. Then press the button , the result is shown in the summary

line with the previous value in the second line. Operate the above steps repeatedly, the meter will

add or reduce cumulatively. The last step is cancelled.

AREA

Press once. The symbol appears in the display.

Press button to take the rst length measurement (e.g. length).

Press again to take the second length measurement (e.g. width).

After taking the second measurement, the area/surface is automatically calculated and displayed

in the summary line. The last individual measured value is indicated at the second line in the

display.

VOLUME

For volume measurements, push button twice until the indicator for volume

measurement appears in the display.

Afterwards, Press this button to measure the length.

Press this button for width.

Press button to take the height,

After taking the third measurement, the volume is automatically calculated and displayed. The

last individual measured value is not displayed.

INDIRECT MEASUREMENT

when measuring heights that require the measurement of two or three

measurements ,as following step:

USING 2 MEASUREMENTS

Press this button , the display shows.

Aim at the upper point (1) and trigger the measurement. After the rst measurement, the

value is adopted.

Keep the instrument as horizontal as possible.

Aim at the lower point (2), press this button , the second distance is measured and adopted.

Meanwhile, the height of (1) and (2) are displayed in the summary line.

USING 3 MEASUREMENTS

Press this button twice; the display shows the

symbol .

Aim at the upper point (1) and press the button to trigger the measurement. After the rst

measurement the value is adopted.

Keep the instrument as horizontal as possible.

Aim at the upper point (2) and press the button . The value is measured and adopted.

Aim at the lower point (3) and press the button to trigger the measurement.

Meanwhile, the height of (1) and (3) will be shown in summary line.

Press the button ,the meter will return to single measurement status.

HISTORICAL STORAGE

Continue press the next value of previous 20 records (measurements or

calculated results) are shown in the reverse order.

Press to retrieve the next value of 20 records .

Press then retrieve the previous value of 20 records.

TECHNICAL SPECIFICATIONS

GENERAL CHARACTERISTICS

Measurement Distance 0.1m ~ 60m (4 in ~197 ft)

Measurement Speed 3 times / s

Battery Type AAA 2 x 1.5V

Battery Life up to 3,000 measurements

Battery indicator Three states: full, medium, low

Dimension 116 x 49 x 28 mm

Weight 100g (Including batteries)

Laser Type 635nm﹤1mW

Laser Class Class II

Dust Protect/Splash proof IP54

Auto power off after 3 min

Auto laser switch-off after 0.5 min

ENVIRONMENTAL REQUIREMENTS

Altitude: 2000m

Operating Temperature 0°C to +40°C(+32°F to +104°F)

Storage Temperature -10 °C to +60°C (14°F to +140°F)

FOLLOWING STANDARDS

EN61326-1 EMC;

EN60825-1 Laser Safety

SPECIFICATIONS

Laser distance meter Code 51269

Basic functions Range Accuracy

Measuring distances

0.1m~60m* ± 1.5 mm**

4 in ~197 ft ± 0.06 in

Measuring units: m / in / ft

Special functions Explanation

Area, Volume Calculations √m2 / ft2 / m3 / ft3

Indirect Measuring with

Pythagorean √Two or three measurements

Addition/Subtraction √

Continuous Measurement √

Max/Min √

multi-line display √Up to four lines show

Reference level setting √ Front edge or end piece edge

Buzzer indication √

Backlight √white

Auto Bias Technology™ √Support for external

calibration

error indication √Display error code

Hold √Automatic

History measurement recodes √20 records

Clear √

Keyboard Type Super Soft-Touch (Long life) Over 1 Million Times

* during daylight or if the target has poor reection properties!

** in favorable conditions (good target surface properties, room temperature)

up to 60 m. In unfavorable conditions, such as intense sunshine, poorly reecting target surface

(black surface) or high temperature variations, the deviation over distances above 10m may

increase more.

MAINTENANCE

Warning: during replacing battery or measuring, keep the sensitive mirror from scratch or

dirt to avoid damaging the mirror or inuencing the measuring precision; and do not charge the

replaced battery to avoid explosion and safety accident!

BATTERY INSTALLATION AND REPLACEMENT

- When the symbol ashes permanently in the display replace the battery immediately.

Use alkaline batteries only.

Remove the batteries before any long period of non-use to avoid the danger of corrosion.

As following steps:

- Turn of the screw, remove battery compartment lid.

- Insert batteries in the two space respectively, observing correct

polarity.

- Close the battery compartment again, and x the screw for reliability.

GENERAL MAINTENANCE

When the surface of meter is dirty, clean with wet cloth and neutral detergent, grinding miller

and solvent are forbidden.

When the meter is damaged and needs to be repaired, please send it to the designated

maintenance center of our company for repair by professional service man, do not repair it without

authorization.

Especially in the process of using, keep the sensitive mirror of meter away

from scratch or dirt to avoid damaging the mirror or inuencing the measuring

precision.

Remove the battery if it won’t be used for a long time.

Troubleshooting – Causes and Corrective Measures

All message codes are displayed with either or “Error”. The following errors can be corrected:

Code Cause Corrective Measure

204 Calculation error Refer to user menu, repeat the procedures

208

Temperature too high

The measuring tool is outside the

operating temperature range from 0

°C to +40 °C

Cool down instrument, make it working

in stable temperature environment

253 Temperature too high Cool down the instrument

255 Receiver signal too weak, measurement

time too long

Use target plate or change a good

refection

256 Received signal too strong

Target too reective use target plate or do

not aim

at strong light objective

Error Hardware error and

uncertainty error

Switch on/off the device several times. If

the

symbol still appears, try to replace the

battery,

Otherwise your instrument is defective.

Please call

your dealer for assistance

NOTES

IMPORTANT!

The maker will not take responsibility for damage or malfunction as a result of the device being

incorrectly used or, applied for a purpose for whith it was not intended.

According to Waste Electrical and Electronic Equipment directive (WEEE), these ones must

be collected and arranged separately. If you have to throw them out, please, do not use the usual

rubbish. Please, contact your distributor for free recycling.

GUARANTEE

The maker guarantees to the device owner 12 months against any manufacture defect.

This guarantee do not cover the parts wich are consumables.

Note: to apply the guarantee its necesary to send the “GUARANTEE CERTIFICATE” duly lled

within one week after purchased the machine to the maker.

ARTICULO / ITEM / ARTICLE: ....................................................................................................................

Nº DE SERIE / SERIE Nº / Nº SERIE: ...........................................................................................................

DISTRIBUIDOR / DISTRIBUTOR / DISTRIBUTEUR: ...................................................................................

PAIS / COUNTRY / PAYS: .............................................................................TEL.:....................................

FECHA DE VENTA / SALE DATE / DATE VENTE:........................................................................................

NOMBRE DEL COMPRADOR / BUYER NAME / NOM DE L’ACHETEUR:..................................................

TEL. COMPRADOR / BUYER TEL. / TEL. DE L’ACHETEUR:........................................................................

CERTIFICADO DE GARANTIA

GUARANTEE CERTIFICATE

CERTIFICAT DE GARANTIE

SELLO / STAMP / CACHET

EGA MASTER GARANTIZA AL COMPRADOR DE ESTA MAQUINA LA GARANTIA TOTAL (DURANTE 12 MESES), DE LAS PIEZAS CON DEFECTOS DE FABRICACION. ESTA

GARANTIA NO CUBRE AQUELLAS PIEZAS QUE POR SU USO NORMAL TIENEN UN DESGASTE. PARA OBTENER LA VALIDEZ DE LA GARANTIA , ES ABSOLUTAMENTE

IMPRESCINDIBLE QUE COMPLETE Y REMITA ESTE DOCUMENTO A EGA MASTER , DENTRO DE LOS SIETE DIAS A PARTIR DE LA FECHA DE COMPRA.

EGA MASTER GUARANTEES TO THE BUYER OF THIS MACHINE THE TOTAL WARRANTY (DURING 12 MONTHS), OF THE PIECES WITH MANUFACTURING FAULTS.

THIS GUARANTEE DOES NOT COVER THOSE PIECES WORN OUT DUE TO A NORMAL USE. IN ORDER TO OBTAIN THE VALIDITY OF THIS WARRANTY , IT IS

ABSOLUTELY NECESSARY TO FULFILL THIS DOCUMENT AND RESEND IT TO EGA MASTER WITHIN 7 DAYS FROM SALE DATE.

EGA MASTER GARANTIE A L’ACHETEUR DE CETTE MACHINE LA GARANTIE TOTALE (PENDANT 12 MOIS) DES PIECES AVEC DEFAUTS DE FABRICATION. CETTE GARANTIE

NE COUVRE PAS LES PIECES QUE PAR UN USAGE NORMAL, SOIENT DETERIOREES. POUR OBTENIR LA VALIDITE DE LA GARANTIE, IL EST ABSOLUMENT IMPERATIF

COMPLETER ET ENVOYER CE DOCUMENT EGA MASTER, DANS UN DELAI DE 7 JOURS A PARTIR DE LA DATE D’ACHAT.

EJEMPLAR PARA EGA MASTER / COPY FOR EGA MASTER / EXEMPLAIRE POUR EGA MASTER