EINHELL ERGO TOOLS E-DP 600 User manual

Original operating instructions
Drywall Sander
Art.-Nr.: 42.599.15 I.-Nr.: 11013 E-DP 600
GB

2
1
2a
3
7
4
3
5
6
8
3
5
7
12
2b
2c

GB
4
6
3
7
8
5
2
1
A
4
3
9
7

GB
4
Caution - Read the operating instructions to
reduce the risk of injury
The impact of noise can cause damage to
hearing.
Wear a breathing mask.
Dust which is injurious to health can be
generated when working on wood and other
materials.
Never use the device to work on any materials
containing asbestos!
Wear Safety goggles.
Sparks generated during working or splinters,
chips and dust emitted by the device can
cause loss of sight.

GB
5
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with
due care. Keep this manual in a safe place, so that
the information is available at all times. If you give
the equipment to any other person, give them
these operating instructions as well. We accept no
liability for damage or accidents which arise due to
non-observance of these instructions and the safety
information.
1. SAFETY REGULATIONS
The corresponding safety information can be found
in the enclosed booklet.
Read all safety regulations and instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
2. LAYOUT (FIG.1)
1. witch
2. 2 Speed regulator
3. Lock for telescopic length extension
/ dust extraction hose
4. Telescopic length extension
5. Lock for lower handle bar
6. Dust extraction hose
7. Sanding/grinding disk
8. Lower handle bar
3. INTENDED USE
The drywall power sander is designed for sanding/
grinding of smoothed dry mortarless walls, for interior
ceilings and walls, as well as to remove residual
hangings, colour, coverings, glue and loose plaster.
The appliance may only be used for the tasks it is
designed to handle. Any other use is deemed to
be a case of misuse. The user/operator - not the
manufacturer - will be liable for any damage or
injuries caused as a result thereof.
Please note that our appliance has not been
designed for use in commercial, trade or industrial
applications.
Our warranty will be voided if the appliance is used
in commercial, trade or industrial businesses or for
equivalent purposes.
4.TECHNICAL DATA
Mains connection 230 - 240 Volt ~ 50 Hz
Power input 600 W
Oscillation rate 600-1,500 rpm
Abrasive paper size Ø 225 mm
Protection class: II /
Weight 3.55 kg
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
LpA Sound pressure level 84 dB(A)
KpA Uncertainty 3 dB
LWA Sound power level 95 dB(A)
KWA Uncertainty 3 dB
W
The impact of noise can cause damage to hearing.
Overall oscillation value determined according to
EN60745
Vibration emission value a = 3.03 m/s²
Caution:
The vibration value changes according to the area of
application of the electric tool and may exceed the
Keep the noise emissions and vibrations to a
minimum.
•Only use appliances which are in perfect working
order.
•Service and clean the appliance regularly.
•Adapt your working style to suit the appliance
•Do not overload the appliance.
•Have the appliance serviced whenever necessary.
•S
•Wear protective gloves.
5. BEFORE STARTING THE
APPLIANCE
5.1 Assembly
Fold the lower handle bar (Fig. 1/ Item 8) and lock the
ever in place (Fig. 1/ Item 5) as shown in Fig 2a-2c.
5.2 Using the telescopic length extension (Fig.7)
Undo the lock for the telescopic length extension
(3) and attach the telescopic length extension (4) as
shown in Fig. 7.
Before you connect the appliance to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Warning!
h
Telescopic handle 1.15 m - 1.65 m
Spindle size M6
Disc size Ø 215 mm

GB
6
Always pull the power plug before making
adjustments to the appliance.
5.3 Changing the abrasive paper (Fig. 3)
The sanding/grinding disk comes with a Velcro
fastening system for sanding/grinding paper. This
permits new sanding/grinding paper to be attached
without a clamping device.
Before you attach a new piece of sanding/grinding
paper, knock out any dirt from the Velcro fastener and
clean with a brush or, if necessary, with compressed
air.
Place the sanding/grinding paper on the sanding/
grinding disk (7). Ensure that the holes of the paper
are aligned with the holes of the sanding disk. Fix the
with your hand.
Caution:
be used.
5.4 Fitting the dust extraction system (Fig. 4)
The dust extraction system prevents the
accumulation of dirt and high dust loads in the air,
and it makes it easier to dispose of the dust.
•Undo the lock for the dust extraction hose (1)
and attach the dust extraction hose (6) as shown
•Tighten the lock (3) again.
•Connect the other end of the dust extraction hose
(6) to a vacuum cleaner.
Advantages:You will protect both the appliance and
your own health.Your work area will also be clean
6. STARTING UP
6.1 ON/OFF switch (Fig. 5)
•T
(1). Then press the locking button ‘A’ to lock the
•T
again and then let go of it.
6.2 Speed regulator (Fig. 6)
•To pre-select the speed turn the knurled screw (2)
on the switch and adjust the speed according to
the work you are doing.
6.4 Swivelling grinding/sanding disk (Fig. 8)
and therefore enables comfortable grinding/sanding
even for overhead work and for working in small
spaces.
7. REPLACING THE POWER
CABLE
If the power cable for this appliance is damaged,
it must be replaced by the manufacturer or its
aftersales service or similarly trained personnel to
avoid danger.
8. Cleaning, maintenance and ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
•Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
•Wipe the appliance with a clean cloth or blast it
with compressed air at low pressure.
•We recommend that you clean the appliance
immediately after you use it.
•Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the appliance. Ensure that no water can
get into the interior of the appliance.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
Caution: The carbon brushes should not be replaced
8.3 Servicing
There are no parts inside the appliance which require
additional maintenance.
8.4 Ordering replacement parts:
Please provide the following information on all orders
for spare parts:
•Model/type of the appliance
•Article number of the appliance
•ID number of the appliance
•Spare part number of the required spare part
For our latest prices and information please call
1300 922 271.
8.5 Changing the sanding disc (Fig. 9)
Hold the sanding disc (7) in place. Loosen the allen
screw (b) on the sanding disc (7) with a allen key.
Lift the sanding disc carefully out.
To assemble the new sanding disc proceed in reverse
order.
Important: Ensure you replace it with a disc that has
the machine in low speed for a couple of minutes to
in Fig. 4.
and safe.

GB
7
9. DISPOSAL AND RECYCLING
The appliance is supplied in packaging to prevent
its being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The appliance and its accessories are made of
various types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.

GB
Anleitung_GE_CH_1855_Li_Kit_SPK7__ 01.07.13 08:40 Seite 17
EINHELL AUSTRALIA PTY LTD
6/166 Wellington Street
Collingwood VIC 3066
Australia
Phone: [phone]
Dear Customer,
All of our products undergo strict quality checks. In the unlikely event that your device develops a fault, please
contact our service department at the address shown on this guarantee certificate. Of course, if you would
prefer to call us then we are also happy to offer our assistance under the service number printed below.
Please note the following terms under which claims under the Einhell Express Guarantee can be made:
1. The benefits conferred by the Einhell Express Guarantee are in addition to all rights and remedies which
you may be entitled to under the Australian Consumer Law, and any other statutory rights you may have
under other applicable laws. This Einhell Express Guarantee does not exclude, restrict or modify any
We do not charge you for the Einhell Express Guarantee.
2. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
3. The Einhell Express Guarantee only covers problems caused by material or manufacturing defects, and
our liability under the Einhell Express Guarantee is limited, at our discretion, to the rectification of these
defects or replacement of the product. Please note that the product has not been designed for use in
commercial, trade or industrial applications. Consequently, the Einhell Express Guarantee will not apply
if the product is used in commercial, trade or industrial applications or for other equivalent activities.
4. The following are also excluded from the Einhell Express Guarantee: compensation for transport
damage, damage caused by failure to comply with the installation/assembly instructions or damage
caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to
the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the
product or use of non-approved tools or accessories), failure to comply with the maintenance and safety
regulations, ingress of foreign bodies into the product (e.g. sand, stones or dust), effects of force or
external influences (e.g. damage caused by the product being dropped) and normal wear resulting from
proper operation of the product. The Einhell Express Guarantee will also not apply if any attempt is made
The Einhell Express Guarantee is valid for a period of 2 years starting from the purchase date of the
product. Claims made under the Einhell Express Guarantee should be submitted before the end of this
guarantee period and within two weeks of the defect being noticed. No claims under the Einhell Express
Guarantee will be accepted if submitted after the end of this guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such
cases, the work performed or parts fitted will not result in an extension of the guarantee period for the
Einhell Express Guarantee, and the Einhell Express Guarantee will not apply for the work performed or
6. To make a claim under the Einhell Express Guarantee, please send the relevant product postage-free to
the address shown below and enclose either the original or a copy of your sales receipt or another dated
proof of purchase. It would help us if you could describe the nature of the problem in as much detail as
possible. If the defect is covered by the Einhell Express Guarantee, your product will be repaired
immediately and returned to you, or we will send you a new device (at our election).
Any costs incurred by you in making a claim under this Einhell Express Guarantee, unless specified
otherwise in this guarantee certificate, must be borne by you.
Of course, we are also happy to offer a chargeable repair service for any defects which are not covered by the
scope of the Einhell Express Guarantee or for products which are no longer covered by the Einhell Express
Guarantee. To take advantage of this service, please send the product to our service address.
such rights or remedies.
to tamper with the product.
parts fitted. This also applies when an on-site service is used.
The guarantee provided in this Guarantee Certificate is given by Einhell Australia Pty Limited
ACN 134 632 858 of 6/166 Wellington Street, Collingwood, Victoria (Telephone number 1300 922 271)
GUARANTEE CERTIFICATE
(Einhell Express Guarantee).
EH 11/2013 (01)