EINHELL CE-JS 8/1 User manual

CE-JS 8/1
Art.-Nr.: 10.915.11 I.-Nr.: 21020
9
DOriginalbetriebsanleitung
Fremdstarter – Energiestation
GB Original operating instructions
Jump Start – Power Bank
FInstructions d’origine
Démarreur externe – station
d’énergie
IIstruzioni per l’uso originali
Avviatore di emergenza – Carica-
batterie portatile
DK/ Original betjeningsvejledning
NJumpstarter – Energistation
SOriginal-bruksanvisning
Starthjälp – Energistation
NL Originele handleiding
Externe starter – energiestation
EManual de instrucciones original
Arrancador de batería - unidad
energética
FIN Alkuperäiskäyttöohje
Apukäynnistin / Varavirtalähde
RUS Оригинальное руководство по
эксплуатации
Внешний аккумулятор – Узел
электропитания
SLO Originalna navodila za uporabo
Zunanji zaganjač– Energetska
postaja
RO Instrucţiuni de utilizare originale
Starter auto – Staţie de energie
GR Πρωτότυπες Οδηγίες χρήσης
Βοηθητική εξωτερική εκκίνηση -
μονάδα ενέργειας
Anl_CE_JS_8_1_SPK9.indb 1 08.02.2021 08:42:45

- 2 -
2a1
2c
2
2b
3 4
3
3
4
1 5
6
7
Anl_CE_JS_8_1_SPK9.indb 2 08.02.2021 08:42:59

- 3 -
4d
4b
Beep,Beep
4c
4a
(559:
XK\KXYK IUXXKIZ
4
5
Anl_CE_JS_8_1_SPK9.indb 3 08.02.2021 08:43:00

GB
- 15 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Children are not allowed to use this equipment.
Children should be supervised so that they do not
play with the equipment. Children are not allowed
to carry out cleaning or maintenance. This equip-
ment is not allowed to be used by people with li-
mited physical, sensory or mental capacities or by
those with insufficient knowledge or experience
unless they are supervised or instructed by a per-
son who is responsible for them.
Key (Fig. 5)
Important! Read carefully before use!
Text on the equipment and jump start cable
Important! Read carefully before use!
1. Never press the “Boost” button before the car
battery has been connected.
2. Never connect the clamps together – risk of a
short-circuit and risk of injury.
3. Jump start only for 12 V cars; connect the red
clamp to the “+” and the black clamp to the “-”
battery pole.
4. „Correct“ LED lights up green = Start the en-
gine within 30 seconds.
5. Red LED + acoustic warning signal = Battery
connected reverse polarity (see 3.)
6. „Correct“ LED ashes green = Press the
„Boost“ button and start the engine within 30
seconds.
7. No LED, no acoustic warning signal = Check
the connector to the equipment, press the
„Boost“ button and start the engine within 30
seconds.
Warning!
1. Keep the equipment out of reach of children!
2. Do not open the equipment - risk of injury!
3. If fewer than 3 LEDs are illuminated, the jump
start is not available.
4. If the engine fails to start within 5 seconds,
stop the jump start operation. Wait at least 1
minute before you repeat the operation.
2. Layout and items supplied
2.1 Layout (Fig. 1)
1 Connection for jump start cable
2 Micro USB charging jack
3 5V/9V USB outlet
4 5V max. 2A USB outlet
5 LED lamp
6 On/Offbutton
7 LED battery capacity indicator
2.2 Items supplied
Please check that the article is complete as
specied in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Anl_CE_JS_8_1_SPK9.indb 15 08.02.2021 08:43:17

GB
- 16 -
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suffocating!
• Jump start power bank
• Jump start cable
• 3-in-1 USB connection cable (Micro/Mini/C)
• USB high-speed charger cable
• Storage case
• Original operating instructions
• Safety instructions
3. Proper use
The jump start power bank is designed for char-
ging smart phones, cameras, tablets, etc. It can
also be used as a torch light. Used with the sup-
plied jump start cable the equipment can also be
used as a support for 12 V starter batteries (lead
acid batteries) in motor vehicles with maximum
petrol engine capacities of 3000 ccm.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse.The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Jump start power bank
Li-Po battery: .......11.1 V – 2500 mAh – 27.75 Wh
Micro USB inlet “IN: 5V/9V”:
................................................ 5 V d.c./3 A (max.)
............................................... 9 V d.c./2 A (max.)
Charging time 5V/1A, approx.: ....................... 7 h
Charging time 5V/2A, approx.: ....................... 4 h
Charging time 5V/3A, approx.: ....................... 2 h
Charging time 9V/2A, approx.: .................... 1.5 h
USB outlet “OUT: “5V/2A”: 5 V DC / 2 A (max.)
USB outlet “OUT:“5V/9V”:
............................................... 5 V d.c./3 A (max.)
............................................... 9 V d.c./2 A (max.)
Jump starting
current: .................... 200 A (5 sec) / 400 A (max.)
Ambient temperature
for jump starting: ....................... + 15 °C - + 40°C
Storage temperature: ................. + 5 °C - + 40 °C
Protection class: ................................................III
5. Before starting the equipment
5.1 Charging the jump start power bank
(Fig. 3)
You can charge up the jump start power bank
on any standard USB outlet (e.g. the charger of
a smart phone). Check that the voltage on the
rating plate is the same as your supply voltage
before you connect the USB charger. We recom-
mend that you charge up the equipment every 4
months.
Important! Pull out the power plug before making
adjustments to the equipment.
Observe the enclosed safety information with de-
tailed information about charging.
The outlets must not be used while charging is in
progress.
• Connect the USB charger to the Micro USB
inlet. Use the supplied USB cable (Fig. 2a) to
do so.
• Plug the charger into the socket outlet and the
battery will be charged. The LEDs of the LED
battery capacity indicator shine (flash) during
charging and indicate the charging status.
When charging is finished, all the LEDs shine.
Anl_CE_JS_8_1_SPK9.indb 16 08.02.2021 08:43:17

GB
- 17 -
The temperature of the battery pack may rise
slightly during the charging operation.This is
normal.
5.2 Battery capacity indicator
Press the ON/OFF button (Fig. 1/Item 6) briey.
The LED for the battery capacity indicator (Fig. 1
/ Item 7) light up. The number of LEDs that are lit
indicate the current charge level of the integrated
Li-Po battery.
100% charged = 4 LED steady on
>25% charged = 1 LED steady on
<25% charged = no LED steady on
5.3 Time limits
To protect the integrated battery cells, the LED
light will switch offafter being in use for approx.
3 hours.
6. LED lamp
Caution! Do not look into the light beam.
• Press the ON/OFF button for 3 seconds – the
LED lamp (Fig. 1 / Item 1) will be permanently
lit.
• Press the ON/OFF button again – the LED
lamp will be lit as a „strobe light“.
• Press the ON/OFF button again – the LED
lamp will be lit as an „SOS“ Morse code sig-
nal lamp.
• Press the button again to switch the LED
lamp off again.
7. Outputs
Caution! Check the voltage and current ratings of
the device you want to connect (e.g. mobile pho-
ne, notebook). Observe the operating instructions
for the device.
The supply time varies according to the level of
the charge of the jump start power bank, the level
of power consumption and the intensity of use of
the connected device. The battery needs char-
ging when the remaining charge is 25% (1 LED
shines) (see section 5). If the input current of the
connected device is very low, the equipment will
switch offagain within a few seconds.The equip-
ment will also switch offif the integrated battery
is empty.
The USB ports can be used in parallel. Please
ensure that the cumulative output current does
not exceed 5 A.
7.1 Charging/operating devices with a USB
connection
a) 5V/2A USB outlet
1. Connect an available (or the supplied 3-in-1)
USB connection cable to the USB port (Fig.
1 / Item 4) on the jump start power bank and
then to the device you want to connect (max.
2A).
2. Press the ON/OFF button (Fig. 1 / Item 6).
b) “OUT 5V/9V” USB outlet
Note: If charging does not work with this outlet,
this means that either the device or the cable is
not supported. In this case, use the 5V d.c. / 2A
USB outlet for charging, as described above.
1. Connect the supplied 3-in-1 USB cable (Fig.
2) to the “OUT 5V/9V” USB port (Fig. 1 / Item
3) on the jump start power bank and then to
the device you want to connect.
2. Press the ON/OFF button (Fig. 1 / Item 6).
3. The parameters required for charging will be
determined at the USB outlet and the connec-
ted device will be charged up. Depending on
the charger cable and the device being char-
ged, the charging time with the “OUT 5V/9V”
USB outlet may be shorter than with the “OUT
5V/2A” USB outlet.
8. Jump starting for the vehicle
The 12 V jump starting function provides welcome
help with starting difficulties due to too little batte-
ry capacity.
Warning! Only the jump start cable is allowed
to be connected during jump starting. Any power
supply to a connected device, e.g. via the USB
port, must be disconnected rst.
• Consult the vehicle’s operating manual for
information about jump starting. Non-obser-
vance can lead to damage to the vehicle.
• Switch off all power consumers on the vehicle
(headlights, radio, …). Never try to start a ve-
hicle without a connected starter battery.
• Make sure that the connector on the jump
start cable is securely connected to the de-
vice socket. If the connection is loose during
jump starting, the connector could melt as a
result of the high current.
• The poles on the vehicle battery must be
Anl_CE_JS_8_1_SPK9.indb 17 08.02.2021 08:43:17

GB
- 18 -
clean and the clamps of the jump start cable
must be securely attached to the battery po-
les.
• Warning! Do not connect together the
clamps of the jump start cable when the
“Boost” button is pressed or while jump
starting is in progress – this will lead to short-
circuiting with sparking, to risk of explosion
and to the destruction of the equipment..
Check that at least 3 LED of the battery capacity
indicator are lit. The equipment temperature must
be within the range of + 5 °C - + 40°C and the am-
bient temperature during jump starting within the
range of – 15°C - + 40°C. Use only the supplied
jump start cable (Fig. 2c).
1. Fig. 4: Pull open the cover on the jump start
cable connection (Fig. 1 / Item 1), push the
cover underneath it to the side and plug the
jump start cable into the equipment.
2. Fig. 4a: Connect the red cable to the positive
pole on the car’s battery and the black cable
to the negative pole on the car’s battery. Make
sure that the clamps are secure. In addition,
make sure that the jump start power bank is
tucked away securely in the engine bay and
will not be able to fall as a result of vibrations
during the jump start operation. The jump
start power bank must not be allowed to
come within the range of moving parts.The
following points 3. – 6. describe the status sig-
nals of the jump start cable. Please follow the
instructions.
3. Fig. 4a: The “Correct” LED on the jump
start cable lights up green. All the existing
connections are OK and the vehicle can be
started within 30 seconds.
4 Fig. 4b: The “Correct” LED on the jump
start cable ashes green. All the existing
connections are OK, but the car battery char-
ge status is very low. Press the “Boost” button
on the jump start cable and wait until the
“Correct” LED lights up green continuously.
Start the vehicle within 30 seconds.
Be particularly careful because pressing the
“Boost” button has the effect of overriding the
safety devices integrated in the jump start
power bank
5. Fig. 4c: The red LED on the jump start
cable lights up and an acoustic warning
signal sounds. The clamps of the jump
start cable are wrongly connected to the car
battery, i.e. with reverse polarity. Remove the
clamps and connect them to the car battery
again but with the correct polarity and in ac-
cordance with the previous instructions.
6. Fig. 4d: No LED lights up on the jump start
cable, nor is there an acoustic warning
signal. Check all the connections, especially
that the clamps are connected to the car bat-
tery with the correct polarity. If all the connec-
tions are OK, the cause is probably a defecti-
ve car battery. Press the “Boost” button on the
jump start cable and wait until the “Correct”
LED lights up green continuously. Start the
vehicle within 30 seconds.
Be particularly careful, because pressing the
“Boost” button has the effect of overriding the
safety devices integrated in the jump start
power bank. Replace the defective car battery
as soon as possible.
7. As soon as the engine is running, remove the
jump start cable from the equipment and then
remove the red clamp from the car battery
rst, followed by the black clamp.
8. Let the engine run.The generator will charge
up the built-in car battery.
At very low temperatures a number of jump start
attempts may be required before the car starts up.
Allow one minute waiting time between each att-
empt. Remove the equipment within 30 seconds
after a successful jump start as far as possible.
The number of times that you can attempt to start
the engine (max. 4 within 10 minutes) varies ac-
cording to the ambient temperature, the condition
of the battery you want to start and the charge
level of the jump start power bank battery.
If too many attempts to start are carried out within
10 minutes, the “Correct” LED will ash green /
red in alternation and further attempts to start will
be blocked.The jump start function will become
available again after a 10-minute waiting period
provided the battery has enough capacity and the
integrated safety device is compliant.
Anl_CE_JS_8_1_SPK9.indb 18 08.02.2021 08:43:17

GB
- 19 -
9. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the power plug before starting any
cleaning work.
Remove all the connected cables from the jump
start power bank.
9.1 Cleaning
• Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
• We recommend that you clean the device
immediately each time you have finished
using it.
• Clean the equipment regularly with a damp
cloth. Do not use cleaning agents or solvents;
these could attack the plastic parts of the
equipment. Ensure that no water can seep
into the device. The ingress of water into an
electric tool increases the risk of an electric
shock.
9.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
9.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
10. Repair
Should the tool experience problems beyond
those mentioned above, let only an authorised
professional or a customer service shop perform
an inspection.
11. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled.The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offices.
12. Storage
Store the equipment and its accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between +5 and
40°C.
Observe the enclosed safety information with
detailed information about storage. Since the bat-
tery reacts if the temperature is too high (above
+40°C) or too low (below 0°C), do not keep the
battery permanently in a vehicle. For transporting
in a vehicle, place the equipment in a suitable
location where it cannot move in response to an
abrupt change in speed and/or direction. Keep
the equipment in its original packaging.
Anl_CE_JS_8_1_SPK9.indb 19 08.02.2021 08:43:18

GB
- 20 -
13. Troubleshooting guide
Fault Possible cause Remedy
The equipment can-
not be switched on:
- Battery voltage too low - Charge battery
Jump starting does
not work
- Battery voltage too low
- Connections on the vehicle con-
nected with reverse polarity
- Temperature outside the tempera-
ture range
- Charge battery
- Check the polarity and connect cor-
rectly
- Try jump starting within the tempe-
rature range
All LED ash - The overload cutout has responded
- Equipment too cold/hot
- Ambient temperature too low/high
- Switch offthe equipment, check for
possible overloading
- Observe equipment temperature of
+ 5°C - + 40°C.
- Observe ambient temperature ran-
ge of – 15°C - + 40°C
Anl_CE_JS_8_1_SPK9.indb 20 08.02.2021 08:43:18

GB
- 21 -
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and
its implementation in national laws, old electric power tools have to be separated from other waste and
disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment
must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.
The old equipment can be returned to a suitable collection point that will dispose of the equipment in
accordance with the national recycling and waste disposal regulations. This does not apply to any ac-
cessories or aids without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers ac-
companying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes
This consignment contains lithium-ion batteries.
In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle
with care. Danger of ignition in case of damage to the consignment package. If the consignment packa-
ge is damaged: Check and if necessary repackage.
For further information contact: 0049 9951 95920-66. Outside Germany charges will apply instead for a
regular call to a landline number in Germany.
Anl_CE_JS_8_1_SPK9.indb 21 08.02.2021 08:43:18

GB
- 22 -
Service information
We have competent service partners in all countries named on the guarantee certicate whose contact
details can also be found on the guarantee certicate. These partners will help you with all service re-
quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Category Example
Wear parts* Battery
Consumables*
Missing parts
* Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
Please ensure that you provide a precise description of the problem and answer the following questions
in all cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Anl_CE_JS_8_1_SPK9.indb 22 08.02.2021 08:43:18

GB
- 23 -
Warranty certicate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the
unlikely event that your device develops a fault, please contact our service department at the address
shown on this guarantee card.You can also contact us by telephone using the service number shown.
Please note the following terms under which guarantee claims can be made:
1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product
neither for their commercial activities nor for any other self-employed activities. These warranty
terms regulate additional warranty services, which the manufacturer mentioned below promises to
buyers of its new products in addition to their statutory rights of guarantee.Your statutory guarantee
claims are not affected by this guarantee. Our guarantee is free of charge to you.
2. The warranty services cover only defects due to material or manufacturing faults on a product which
you have bought from the manufacturer mentioned below and are limited to either the rectication of
said defects on the product or the replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or professional applica-
tions. A guarantee contract will not be created if the device has been used by commercial, trade or
industrial business or has been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect
installation, a failure to follow the operating instructions (for example connecting it to an incorrect
mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-
posing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the
use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,
stones or dust, transport damage), the use of force or damage caused by external forces (for ex-
ample by dropping it).
- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal
use of the device.
4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-
arantee claims should be submitted before the end of the guarantee period within two weeks of the
defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.
The original guarantee period remains applicable to the device even if repairs are carried out or
parts are replaced. In such cases, the work performed or parts tted will not result in an extension
of the guarantee period, and no new guarantee will become active for the work performed or parts
tted. This also applies if an on-site service is used.
5. To make a claim under the guarantee, please register the defective device at:
www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new
device. Devices that are returned without proof of purchase or without a rating plate shall not be
covered by the guarantee, because appropriate identication will not be possible. If the defect is co-
vered by our guarantee, then the item in question will either be repaired immediately and returned to
you or we will send you a new replacement.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by
the scope of this guarantee or for units which are no longer covered. To take advantage of this service,
please send the device to our service address.
Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as
set out in the service information in these operating instructions.
Anl_CE_JS_8_1_SPK9.indb 23 08.02.2021 08:43:18