Eizo CuratOR EX190 User manual

Instructions for Use
1MP 19" LCD Monitor
Important
Please read the safety information and all information delivered
with the product carefully to familiarize yourself with safe and
effective usage.

EIZO GmbH
Carl-Benz-Straße 3
76761 Rülzheim
Germany
1071568-005
06/2022 Technical data subject to change.
Copyright © EIZO GmbH 2022.
All rights reserved.
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to
prevent damage to property. The notices referring to your personal safety are highlighted in the manual
by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These
notices shown below are graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that material damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of
danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a
warning relating to property damage.
Qualified personnel
The product/system described in this documentation may be operated only by personnel qualified for
the specific task in accordance with the relevant documentation, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are ca-
pable of identifying risks and avoiding potential hazards when working with these products/systems.
Use of EIZO products
WARNING
EIZO products may only be used for the applications described in the catalog and in the relevant tech-
nical documentation. If products and components from other manufacturers are used, these must be
recommended or approved by EIZO. Proper transport, storage, installation, assembly, commissioning,
operation and maintenance are required to ensure that the products operate safely and without any
problems. The permissible ambient conditions must be complied with. The information in the relevant
documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of their respective owners. Please refer to the
trademarks listed in the appendix. The remaining trademarks in this publication may be trademarks
whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of liability
We have reviewed the contents of this publication to ensure consistency with the hardware and soft-
ware described. Since variance cannot be precluded entirely, we cannot guarantee full consistency.
However, the information in this publication is reviewed regularly and any necessary corrections are in-
cluded in subsequent editions.

Table of contents
CuratOR EX190
Instructions for Use, 06/2022 3
Table of contents
Legal information ............................................................................................................. 2
1 Introduction....................................................................................................................... 6
1.1 Contents of this document ........................................................................................6
1.2 Intended use .............................................................................................................6
1.3 User groups ..............................................................................................................7
2 Safety information ............................................................................................................ 8
2.1 General safety instructions .......................................................................................8
2.2 Product-specific safety instructions ........................................................................12
3 Description...................................................................................................................... 13
3.1 Scope of delivery ....................................................................................................13
3.2 Features..................................................................................................................14
4 Setup and installation .................................................................................................... 15
4.1 Installation site ........................................................................................................15
4.2 Installing the monitor...............................................................................................16
5 Connecting...................................................................................................................... 17
5.1 Safety information for connection ...........................................................................17
5.2 Device connectors ..................................................................................................19
5.2.1 Connector locations .................................................................................. 19
5.2.2 Connection panel ...................................................................................... 20
5.3 Connecting the power cable ...................................................................................21
5.4 Connecting the signal cable....................................................................................22
6 Commissioning............................................................................................................... 23
6.1 Switching on the monitor ........................................................................................23
6.2 Using a screen saver ..............................................................................................23
6.3 Selecting the LUT ...................................................................................................23
6.4 Adapting the monitor to an analog video source ....................................................24
6.4.1 Adjusting the position, phase, and frequency ........................................... 24
6.4.2 Adapting brightness and contrast ............................................................. 25
6.5 Adapting the monitor using Force Mode.................................................................26
6.5.1 Introduction to Force Mode ....................................................................... 26
6.5.2 Basic information on timing....................................................................... 26
6.5.3 Entering timing data .................................................................................. 29
6.5.4 Determining the timing data ...................................................................... 30
7 Operation......................................................................................................................... 33
7.1 Operator controls ....................................................................................................33
7.2 Locking or unlocking the OSD menu ......................................................................34
7.3 Overview of the OSD menu ....................................................................................35

Table of contents
4
CuratOR EX190
Instructions for Use, 06/2022
7.4 "Image" menu .........................................................................................................35
7.5 "Geometry" menu ...................................................................................................37
7.6 "Signal" menu .........................................................................................................40
7.7 "LUT" menu ............................................................................................................42
7.8 "Info" menu .............................................................................................................43
7.9 "Others" menu ........................................................................................................44
7.10 "Force Mode" menu ................................................................................................47
7.11 "Adjust LUT" menu .................................................................................................48
7.12 "Expert" menu.........................................................................................................50
7.13 "Expert 2" menu......................................................................................................51
8 Cleaning and check settings ......................................................................................... 54
8.1 Cleaning..................................................................................................................54
8.1.1 Recommended cleaning agents and disinfectants ................................... 54
8.1.2 Prohibited cleaning agents and disinfectants............................................ 55
8.2 Check settings ........................................................................................................55
9 Troubleshooting ............................................................................................................. 56
9.1 Fault correction .......................................................................................................56
9.2 Additional information .............................................................................................56
10 Technical specifications ................................................................................................ 57
10.1 Monitor characteristics............................................................................................57
10.2 Voltage supply ........................................................................................................57
10.3 Electronics ..............................................................................................................57
10.4 Inputs/Outputs ........................................................................................................58
10.5 Controls and connectors.........................................................................................58
10.6 Mechanical design ..................................................................................................58
10.7 Climatic conditions..................................................................................................59
10.8 Safety specifications ...............................................................................................59
11 Dimension drawings ...................................................................................................... 60
11.1 Monitor without stand..............................................................................................60
11.2 Monitor with stand...................................................................................................61
12 Appendix ......................................................................................................................... 62
12.1 Markings and symbols ............................................................................................62
12.2 Information on electromagnetic compatibility (EMC) ..............................................63
12.3 FCC Declaration of Conformity...............................................................................68
12.4 China RoHS (Restriction of Hazardous Substances) .............................................69
12.5 Declaration of compliance with India RoHS............................................................71
12.6 Environmental protection ........................................................................................71
12.7 Warranty .................................................................................................................71

Table of contents
CuratOR EX190
Instructions for Use, 06/2022 5
12.8 Repairs ...................................................................................................................71
12.9 Additional devices...................................................................................................71
12.10 Contact ...................................................................................................................71
12.11 Trademarks.............................................................................................................72
Index ................................................................................................................................ 73

Introduction
1.1 Contents of this document
6
CuratOR EX190
Instructions for Use, 06/2022
1 Introduction
1.1 Contents of this document
This document explains the functionality and the approved use of the CuratOR EX190. To
ensure clarity, it does not contain all detailed information on this product.
The contents of this document are neither part of a previous or existing agreement, commit-
ment or legal relationship, nor does it modify such.
Note
This documentation is available in electronic format only. It can be found on the CD-ROM
provided and can be downloaded from www.eizo-or.com.
1.2 Intended use
Intended purpose
The CuratOR EX190 is intended for the display of still images and moving images from vari-
ous commercially available devices commonly used in a medical environment, in particular
radiology. The monitor is optimized for the reproduction of grayscale X-ray images. The
monitor is not suitable for mammography.
Intended patient population and medical conditions
The EX190 can be used for the intended purpose irrespective of age, body weight and gen-
der.
The EX190 is intended to be used in combination with or mounted on medical devices. The
monitor therefore has no direct contact with the patient.
The EX190 is intended to display still images and moving images from various commercially
available (medical) devices commonly used in a medical environment. The monitor cannot
be used for direct diagnosis and as main device for monitoring live support equipment.
Intended users
The intended users for the EX190 are qualified healthcare professionals.
Intended environment
The EX190 is intended to be used in professional healthcare facilities such as clinics and
hospitals. The monitor can be used in operating rooms (OR) or near patients, but is not lim-
ited to them. The monitor is not intended for direct patient contact!
The EX190 is not suited for the following environments:
• Home-based healthcare facilities.
• Near short-wave therapy devices.
• Near an MRI-System.
• Built into vehicles, including ambulances.

Introduction
1.3 User groups
CuratOR EX190
Instructions for Use, 06/2022 7
Note
Serious incident
Any serious incident that has occurred in relation to the device should be reported to the
manufacturer and the competent authority of the Member State in which the user and/or
patient is established.
1.3 User groups
User
In the following, healthcare personnel such as surgeons or medical technicians are referred
to as the "user".
Service / service personnel
"Service" or "Service personnel" identifies authorized personnel with knowledge of electrical
and signal connection, local standards for image quality requirements, and safety of medical
products, for example a hospital technician or manufacturer of medical devices.
Cleaning staff
"Cleaning staff" refers to personnel responsible for cleaning medical devices.

Safety information
2.1 General safety instructions
8
CuratOR EX190
Instructions for Use, 06/2022
2 Safety information
2.1 General safety instructions
Correct and safe operation of EIZO devices assume professional transport, storage, installa-
tion, and connection, as well as careful operation and service.
The devices may only be used for applications for which they are intended.
For safety reasons, the following precautions must be observed:
DANGER
Please observe all warning information present on the device and in the instructions for use.
There is a danger to life if warnings are not obeyed. Severe personal injury or damage to property
may occur.
Observe the safety requirements of EN 60601-1 (IEC 60601-1)
To prevent injury to patients and users, connect the electrical system in accordance with the safety
requirements of EN60601‑1 (IEC60601‑1) for "Safety requirements for medical electrical systems".
Connecting the protective earth conductor
If the device is connected to line power, the device must be connected to a protective ground con-
ductor. This is the only way to ensure that the touch leakage current in a first fault event does not ex-
ceed 500 µA.
The interruption of the device's protective conductor is considered a first fault event in accordance
with EN 60601-1.
Use the following measures to ensure that the leakage currents remain below the specified limits:
• Separators for signal input unit or signal output unit
• Use of a safety isolating transformer
• Use of the additional protective ground terminal
Mounting of the monitor: The monitor's suspension arm must have its own protective ground conduc-
tor. This protective ground conductor guarantees, together with the protective ground conductor of
the monitor, that the housing leakage current always remains less than 500µA, even in the event of
a single fault condition.
No unauthorized opening of the device / no unauthorized service or maintenance work
The device may only be opened by qualified personnel. Likewise, service or maintenance work may
only be carried out by qualified personnel. There is a risk of electric shock.
No liability is accepted for death and injury to persons or damage to property resulting from work car-
ried out by non-qualified personnel.
Do not touch components in the device
If the device is connected to the line power, components in the device are subjected to high voltages.
Touching the components may be fatal.
No contact between device and patients
The device is not suitable for direct contact with a patient. The device and patient must never be
touched simultaneously. Otherwise there is a danger to life and limb.

Safety information
2.1 General safety instructions
CuratOR EX190
Instructions for Use, 06/2022 9
DANGER
Please observe all warning information present on the device and in the instructions for use.
There is a danger to life if warnings are not obeyed. Severe personal injury or damage to property
may occur.
Never use defective power cables
If a damaged or unsuitable power cable is used, it could result in a fire or electric shock. Only use
power cables with PE contacts approved by the manufacturer.
Disconnect the power cable correctly
When disconnecting the power cable, always do so by holding the plug. Ensure that your hands are
dry. There is a risk of electric shock.
Do not insert any objects into the housing
Objects inserted into the housing may result in an electric shock or damage to the device.
Do not place any objects on top of the device
If you place objects on top of the device, this can lead to overheating and fire.
Avoid penetration of liquid
Liquids seeping into the device may result in electric shock or device failure.
CAUTION
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
Connection must be carried out by specialists
Please ensure that all steps are taken to avoid injuries or incorrect diagnoses.
• Only use the video cables specified by the manufacturer for the connection.
• Only use power cables with PE contacts.
• Only use power outlets with PE contacts.
• Do not connect too many devices to a power outlet or extension cable.
• Observe the information provided by the respective manufacturer.
• If required by the application or local regulations, QA software must be used for quality control
and documentation.
Connection in the USA and Canada
Molded power supply plugs must comply with the requirements for "hospital grade attachments" CSA
Std. C22.2 No.21 and UL498.
Connection in China
Only use power cables approved for China. These power cables are identified by the labels "CCC" or
"CQC".
Observe the country-specific regulations
Observe all regulations of the country in which the device is used.

Safety information
2.1 General safety instructions
10
CuratOR EX190
Instructions for Use, 06/2022
NOTICE
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
• Desktop installation:
Place the device on a solid and level surface. The attached stand, as well as the installation sur-
face, must be suitable for the weight of the device.
• For mounting on a wall or ceiling suspension:
The mount unit must be suitable for the weight of the device.
• For installation in a rack:
Observe the installation sequence, and provide ventilation for the device.
Provide adequate air circulation
When installing the device, ensure that there is adequate air circulation for operation. The permissi-
ble ambient temperature range must not be violated. Otherwise, the device could be destroyed by
overheating.
Avoid sources of heat
Do not install the device in the vicinity of sources of heat, such as radiators, heating appliances or
other devices that can generate or emit heat.
Do not subject the device to jolting or shocks
The device contains sensitive electronic components that could be damaged by jolting or shocks.
Only switch on a cold device following adaptation to room temperature
If the device is brought into a room with a higher or rising temperature, condensed water will form in
and on the device. Do not switch on the device until the condensed water has evaporated. Other-
wise, the device could be damaged.

Safety information
2.1 General safety instructions
CuratOR EX190
Instructions for Use, 06/2022 11
NOTICE
Extensive damage to property may result if the device is not connected correctly
That is why you should observe the warning information:
Transportation only in original packaging
Use the original packaging for transportation, and transport in the correct shipping position. Be sure
in particular to protect the monitor LCD modules from shocks.
Care of device / cleaning agents
• Remove water drops immediately; extended contact with water discolors the surface.
• Only clean the surfaces using the cleaning agents referred to in the Instructions for Use.
• Monitor: The screen is extremely sensitive to mechanical damage. Absolutely avoid scratches,
shocks, etc.
What to do if the device is faulty
If the following conditions exist, the device must be disconnected from the line power supply and
checked by qualified personnel:
• Damage to the plug or power cable.
• After liquid seeps into the device.
• If the device has been exposed to moisture.
• If the device does not function or if a fault cannot be eliminated using the Instructions for Use.
• If the device has been dropped and/or the housing damaged.
• If the device smells of burning or makes peculiar noises.
Be aware of the monitors aging
Note that monitors can fail as a result of aging, and that image properties such as brightness, con-
trast,and color value can change.
Do not touch the monitor screen
Due to mechanical pressure or electrostatic discharges, touching the screen can result in brief distur-
bances to the image.

Safety information
2.2 Product-specific safety instructions
12
CuratOR EX190
Instructions for Use, 06/2022
2.2 Product-specific safety instructions
CAUTION
Check the gray levels
After each LUT recalculation performed in the "Adjust LUT" menu, it is absolutely neces-
sary to apply an appropriate test pattern and check that all gray levels are displayed cor-
rectly.
CAUTION
Setting the monitor height / turning the display
When the monitor is installed on a stand, setting the monitor height or turning the display
can result in injuries.
• Carefully change the monitor height.
• When changing the height of the monitor or turning the display, make sure that you do
not trap your fingers or any other objects.
• To turn the display, move the monitor to the highest monitor position.
CAUTION
Tilting the monitor
Tilting the monitor can result in injuries or damage to the device.
• Ensure that the monitor is stable after installing a stand.
NOTICE
Subsequent installation of a stand
If a stand is subsequently attached to the monitor, the stand must meet the requirements
of standard EN60601 so that the system, comprising the stand and monitor, meets the re-
quirements.
Note
No zero error rate
LCD monitors do not have a zero error rate. For this reason, the image parameters can
change over time, e.g. reduced luminance or changing/fading colors.
Note
Image quality
To maintain constant image quality, EIZO recommends cleaning the monitor on a regular
basis and checking image properties in accordance with all applicable local regulations.

Description
3.1 Scope of delivery
CuratOR EX190
Instructions for Use, 06/2022 13
3 Description
3.1 Scope of delivery
The device and various components are included in the scope of delivery. After unpacking,
check the scope of delivery for correctness and completeness.
Note
Keep the packaging material for subsequent transport of the device.
Device
The CuratOR EX190 is a 1MP 19" LCD Monitor for installation in a ceiling or wall mount, or
for installation in a stand. The CuratOR EX190-S version has a stand. Otherwise, the ver-
sions are identical.
Product Order number Description
CuratOR EX190 6GF62102EL10 Without stand
CuratOR EX190-S 6GF62102EL01 With stand
Components
Components
The following components are included in the scope of delivery:
• Signal cable
– DVI single link cable
– VGA-DVI-I adapter
– DisplayPort cable
• General safety instructions (22 languages)
• CD-ROM with the documentation

Description
3.2 Features
14
CuratOR EX190
Instructions for Use, 06/2022
3.2 Features
The CuratOR EX190 has the following features that permit a wide range of applications:
Perfect picture reproduction thanks to LCD technology
The use of LCD technology eliminates picture geometry distortions and color spots.
The monitor delivers flicker-free images even at low border rates (60 Hz). The monitor thus
meets the strictest ergonomic requirements.
Screen resolution
The EX190 is equipped with an active 19" TFT display that has an extremely wide viewing
angle. The monitor offers maximum gray scale contrast across a very wide viewing angle
(in-plane switching (IPS) technology).
The optimum screen resolution is 1280x1024pixels. Video signals with other resolutions,
as are common in medical technology, are automatically adapted to the screen size. Alter-
natively, they can be displayed in original size (1:1).
Digital and analog video inputs
The monitor is connected to a digital video source using DisplayPort or DVI-I. Analog video
sources can be connected via BNC (monochrome) or via DVI-I (analog).
Use the On Screen Display (OSD) to adapt the monitor if necessary.
Force Mode
Using the Force Mode function, the EX190 can be adapted to special timing settings.
Dynamic key help
Dynamic key help displays the functions of the keys, simplifying navigation in the OSD
menu.
Adjustable LUT
The adjustable LUT functions allows manual recalculation of the lookup table. This allows
users to modify the gamma model, luminance settings, or color parameters in accordance
with local needs or preferences.
The LUT is recalculated via the OSD menu without having to access external calibration
software. The reset LUT is calculated immediately, saved in the device, and used internally.

Setup and installation
4.1 Installation site
CuratOR EX190
Instructions for Use, 06/2022 15
4 Setup and installation
CAUTION
Changes to device
Do not make any mechanical or electric changes to the device. Otherwise the device war-
ranty becomes invalid.
The manufacturer is not liable for changes made to the device.
4.1 Installation site
Note the following conditions at the installation site.
NOTICE
The power switch and connections must be accessible at all times
When installing and connecting the monitor, ensure that the power switch and the connec-
tions are accessible at all times.
NOTICE
Condensation
If the device is brought into a warm environment from a cold one, condensation may form
in the device. This could result in a short circuit when switching on the device, damaging it.
• Wait until the condensed water has evaporated, including that inside the device, before
you switch it on. This can take several hours.
Sufficient ventilation
Ventilation holes are located on the rear of the housing.
If the ventilation holes are covered or closed, the heat generated in the monitor will not be
dissipated sufficiently.
• Do not cover the ventilation holes.
• Do not close the ventilation holes.
• The minimum distance from the top, back, and side of the monitor to the wall must be at
least 10cm, and at least 15cm from other heat-emitting devices.
Avoid dusty environments
The monitor is intended for use in the clean environment of medical diagnostics. In dusty
environments, ventilation holes in the back can allow dust to penetrate into the monitor. In
the worst case, deposits are possible which become evident as dark spots in a white picture
and result in deterioration of the luminance.
• Protect the monitor from dust, for example through appropriate construction measures at
the installation site.
• During transport, use the original packaging or service packaging.

Setup and installation
4.2 Installing the monitor
16
CuratOR EX190
Instructions for Use, 06/2022
Maintain the permissible ambient temperature
The ambient temperature should be in a range of +5 °C to +40 °C. If the ambient tempera-
ture exceeds this range it could result in overtemperature in the monitor. In this case the Op-
eration LED initially flashes orange. If the temperature continues to rise the LED will flash
red and brightness will be reduced to prevent overheating.
Avoid reflections on the screen
The monitor has an anti-glare surface that is only effective if the screen is clean and grease-
free.
• Comply with the specifications for Cleaning [}54].
• Position the monitor to avoid reflections on the display area.
Reflections can be caused by lights, windows, furniture with shiny surfaces, or light-col-
ored walls.
• In order to reduce reflections on the monitor, only use non-dazzling reflector bulbs for the
ceiling lighting.
Avoid shocks and impacts
The monitor is sensitive to shock. Shocks and impacts on the panel surface can lead to total
failure.
• Ensure that such mechanical influences are avoided.
Movable installation
If the monitor is installed such that it can move, make sure that persons or objects in the fa-
cility are not endangered by the monitor's range of movement.
4.2 Installing the monitor
Mounting on a pole or a monitor stand
Multiple monitors can be installed flush horizontally and vertically to one another. The moni-
tor has a VESA100 x 100 adapter.
Note the following during installation:
• The maximum torque for attaching to the holder is 3 Nm.
• The screws used for attaching to the holder must meet the following requirements:
Number 4
Thread M4
Solidity class 8.8
Insertion depth 5 mm to 10 mm
• Mounts must be tested and approved by the manufacturer for the weight to be sup-
ported.
• An installed stand must be sufficiently stable to withstand tilting of up to 10° without top-
pling the monitor.

Connecting
5.1 Safety information for connection
CuratOR EX190
Instructions for Use, 06/2022 17
5 Connecting
5.1 Safety information for connection
All safety information and warnings for the device must be observed to ensure danger-free
operation.
CAUTION
Changes to device
Do not make any mechanical or electric changes to the device. Otherwise the device war-
ranty becomes invalid.
The manufacturer is not liable for changes made to the device.
CAUTION
Shielding measures
Follow all shielding measures in accordance with local EMC directives. If these guidelines
are not observed, device malfunction may result.
CAUTION
Grounding
The permissible leakage current is not exceeded during the first fault event in accordance
with EN60601-1. The device is grounded with an additional protective conductor to ensure
the greatest possible electric safety.
CAUTION
Excessive currents, short circuits, and ground faults
In accordance with national standards and regulations, protection against excessive cur-
rents, short circuits, and ground faults must be incorporated into the building installation.
NOTICE
Changes to device settings
Device settings may only be adjusted by service personnel.
NOTICE
Disconnecting from line power
Always set the power switch to "Off" before disconnecting the device from power. Other-
wise the device could be destroyed.

Connecting
5.1 Safety information for connection
18
CuratOR EX190
Instructions for Use, 06/2022
NOTICE
Cable installation
Observe the following instructions:
• Only shielded cables are to be used for all signal connections.
• The connecting cables must not be kinked.
• The minimum bending radius of a connecting cable generally equals five times the ca-
ble diameter.
• Do not route signal cables and power cables next to one another. Otherwise, line power
subject to heavy interference could result in reversible pixel errors.
• The device must not share a line power supply with motors or valves (interference!).
• Externally connected cables can represent a trip hazard. Make sure that all incoming
cables are safely routed.
• If the device offers strain relief mechanisms for the cables, use them to prevent unin-
tended loosening of connected cables.

Connecting
5.2 Device connectors
CuratOR EX190
Instructions for Use, 06/2022 19
5.2 Device connectors
5.2.1 Connector locations
The connectors are located in the connection panel behind a cover on the back of the moni-
tor. The power switch is not covered and is freely accessible.
3RZHUVZLWFK6FUHZ&RYHU
Fig.: Rear view with cover
*URXQGLQJFODPS*URXQGLQJVFUHZ
Fig.: Rear view without cover

Connecting
5.2 Device connectors
20
CuratOR EX190
Instructions for Use, 06/2022
5.2.2 Connection panel
CAUTION
Opening the connection panel cover
• Only service may open the connection panel cover.
• The screw torque may not exceed 0.75Nm +/- 0.05Nm.
• Patients must not be present when the cover is open.

DisplayPort 5V/1A DVI-I BNC
In
BNC
Out
USB
Type B
USB
Type A
Power
connector
Power
switch
Fig.: EX190 connection panel
DisplayPort
The monitor has a DisplayPort connector.
5 V connector
The monitor has a 5 V output that can be used to supply external devices.
DVI interface
The monitor has a DVI-I connector.
BNC In
Input for BNC connector "G" for displaying gray scale images.
BNC Out
Output for BNC connector "G".
USB ports
The USB-A ports enable communication with external devices.
The USB-B port enables communication between the monitor and a connected PC, or can
be used for service purposes.
Power connector
The device's power supply is connected using an appliance plug.
Power switch
The power switch is to the right next to the connection panel cover and is used to turn the
device on and off.