Eizo FlexScan MX300W User manual

Important
Please read this User’s Manual carefully to
familiarize yourself with safe and effective
usage procedures.
Please retain this manual for future
reference.
FCC Declaration of Conformity................................ 31
SAFETY SYMBOLS ...................................................2
PRECAUTIONS.....................................................3
1. Introduction.............................................................7
1-1. Features ............................................................ 7
1-2. Buttons and Indicators ...................................... 8
1-3. Utility Disk ......................................................... 9
2. Installation.............................................................10
2-1. Environmental Settings ................................... 10
2-2. Making Use of USB (Universal Serial Bus) ..... 12
3. Screen Adjustment and Settings ..........................13
3-1. Basic Operation and Functions ....................... 13
3-2. Color Adjustment............................................. 15
3-3. Power-save Setup ........................................... 18
3-4. Off Timer ......................................................... 19
3-5. Locking the Settings........................................ 19
3-6. Power Indicator Setting ................................... 20
3-7. Displaying Lower Resolutions ......................... 20
3-8. Setting the Orientation of the Adjustment Menu .... 21
3-9. Displaying EIZO logo....................................... 21
4.Troubleshooting .....................................................22
5. Reference .............................................................24
5-1. Attaching an Arm............................................. 24
5-2. Cleaning .......................................................... 25
5-3. Specifications .................................................. 26
5-4. Glossary.......................................................... 29

2
SAFETY SYMBOLS
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and can
be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury and/or
propertyor product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2007 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be
reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information
confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt
of said information. Although every effort has been made to ensure that this manual provides up-to-date
information, please note that EIZO monitor specifications are subject to change without notice.
Macintosh is registered trademarks of Apple Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards Association.
Windows is a registered trademark of Microsoft Corporation.
PowerManager and RadiCS are trademarks of EIZO NANAO CORPORATION.
ScreenManager, FlexScan and EIZO are registered trademarks of EIZO NANAO CORPORATION
Product specifications may vary depending on the region.
Confirm the specifications in the manual written in the language of the region of purchase.
• It shall be assured that the final system is in compliance to IEC60601-1-1 requirement.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in
malfunction of the monitor.
Install the equipment in a controlled environment, where such effects are avoided.
• This is a monitor intended for use in a medical image system.

PRECAUTIONS
3
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was originally shipped.
If operated outside the region to which it was originally shipped, the product may not perform as
stated in the specifications.
This product is designed for use in Japan only and cannot be used in any other countries.
• To ensure personal safety and proper maintenance, please read this section and the caution statements
on the unit (refer to the figure below).
[Location of the Caution Statements]
[Symbol on the Unit]
Symbol Location This symbol indicates
Front Power switch
Touch to turn the monitor’s power on or off.
Rear
Name Plate Alternating current
Rear Alerting electrical hazard
Rear Caution
Refer to SAFETY SYMBOLS section in this manual.
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes
strange noises, disconnect all power connections immediately and contact
your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or burn.

4
PRECAUTIONS
WARNING
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers may
result in fire, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or
spillage into the cabinet may result in fire, electric shock, or equipment damage. If an
object or liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit
checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment
damage.
If the unit falls, disconnect the power immediately and ask your dealer for advice.
Do not continue using a damaged unit. Using a damaged unit may result in fire or
electric shock.
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
• Do not place outdoors.
• Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
• Do not place in a dusty or humid environment.
• Do not place in a location where the steam comes directly on the screen.
• Do not place near heat generating devices or a humidifier.
• Do not place in an inflammable gas environment.
To avoid danger of suffocation, keep the plastic packing bags away from
babies and children.
Use the enclosed power cord and connect to the standard power outlet of your
country.
Be sure to remain within the rated voltage of the power cord.Not doing so may result
in fire or electric shock.
Power supply: 100-120/200-240 Vac, 50/60 Hz
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may cause in fire or electric shock.
Use the correct voltage.
• The unit is designed for use with a specific voltage only. Connection to another
voltage than specified in this User's Manual may cause fire, electric shock, or
equipment damage.
Power supply: 100-120/200-240 Vac, 50/60 Hz
• Do not overload your power circuit, as this may result in fire or electric shock.
OK

PRECAUTIONS
5
WARNING
Handle the power cord with care.
• Do not place the cord underneath the unit or other heavy objects.
• Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord may
result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user's manual of the arm
stand and install the unit securely.
Not doing so may cause the unit to come unattached, which may result in injury or
equipment damage. When the unit is dropped, please ask your dealer for advice.
Do not continue using a damaged unit. Using a damaged unit may result in fire or
electric shock. When reattaching the tilt stand, please use the same screws and
tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the eyes or
mouth.
If any part of the skin or body comes in direct contact with the panel, please wash
thoroughly. If some physical symptoms result, please consult your doctor.
Lamps contain mercury, dispose according to local, state or federal laws.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with
the cord attached is dangerous. It may result in injury.
Carry or place the unit according to the correct specified methods.
• When carrying the unit, grasp and hold firmly as shown in the illustration below.
• Do not unpack or carry the unit only by a single person, since the large size unit
is so heavy.
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
• Do not place any objects on the ventilation slots.
• Do not install the unit in a closed space.
• Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire, electric
shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.

6
PRECAUTIONS
CAUTION
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period, disconnect the
power cord from the wall socket after turning off the power switch for the
safety and the power conservation.
Notice for this monitor
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a
monitor in lower brightness is recommended.
The LCD panel is manufactured using high-precision technology. However, note that the appearance of any
missing pixels or lit pixels does not indicate damage to the LCD monitor.
Percentage of effective pixels : 99.9994% or higher.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker,
please contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in damage to the screen. There
will be prints left on the screen if the pressed image is dark or black. If pressure is repeatedly applied to the
screen, it may deteriorate or damage your LCD panel. Leave the screen white or black to decrease the prints.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or timer to avoid displaying the same image for extended
periods of time.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until
dew condensation disappears, otherwise it may cause some damages to it.
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in
damage to the panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
To use the monitor comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

1. Introduction
7
1. Introduction
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
•29.8 inch class wide screen format LCD
•WQXGA (2560 × 1600) display compliant
•HDCP signal (SIGNAL2) compliant
•Dual-display compliant by introducing dual-input system (DVI-D × 2 connectors)
•DVI digital input (TMDS) compliant
•Horizontal scan frequency: 31 - 100 kHz
•Vertical scan frequency: 25.5 - 61 Hz (VGA TEXT: 69 - 71 Hz)
•Resolution: 2560 dots × 1600 lines
•Compatible with frame synchronization mode (59 - 61 Hz)
•Smoothing (soft - sharp) function
•DICOM mode (CAL Switch function)
•CAL Switch function for selecting an optimal calibration mode
•The quality control software "RadiCS LE" (for Windows) used to calibrate the monitor is
included(refer to the EIZO LCD Utility Disk).
•The utility software "ScreenManager Pro for Medical" (for Windows) to control the monitor from
a PC with mouse/keyboard is included (refer to the EIZO LCD Utility Disk).
•Portrait/Landscape display available (rotate 90 degrees clockwise)
Tips
•This monitor supports the Portrait/Landscape display. This function allows you to change the
orientation of the Adjustment menu when using the monitor screen in vertical display position.
(Refer to "3-8. Setting the Orientation of the Adjustment Menu" on page 21.)
•If you use the monitor with“ Portrait” position, the setting may be required to change
depending on the graphics board used in your PC. Refer to the manual of the graphics board for
details.


8
1. Introduction
1-2. Buttons and Indicators
1. Input Signal Selection button
2. Mode button
3. Enter button
4. Control buttons (Left, Down, Up, Right)
5. Power button
6. Power indicator
Indicator status Operation status
Blue The screen is displayed
Orange Power saving
Off Power off
*ScreenManager®is an EIZO's nickname of the Adjustment menu.
Buttons
Adjustment menu
(ScreenManager ®*)

1. Introduction
9
1-3. Utility Disk
An "EIZO LCD Utility Disk" (CD-ROM) is supplied with the monitor. The following table shows the
disk contents and the overview of the application software programs.
Disk contents and software overview
The disk includes a monitor information file, application software programs for adjustment, and User’s
Manual. Refer to "Readme.txt” or the "Readme" file on the disk for software startup procedures or file
access procedures.
Item Overview For Windows For Macintosh
A “Readme.txt” or “Readme” file √ √
Color Profiles
(ICC Profiles)
Color profiles - √
RadiCS LE RadiCS LE is quality control software used to calibrate
the monitor and manage the calibration history.
(A PC must be connected to the monitor with the
supplied USB cable.) Refer to the description later.
√ -
ScreenManager
Pro for Medical
A utility software program to control monitor adjustments
from a PC using its mouse and keyboard.
(A PC must be connected to the monitor with the
supplied USB cable.) Refer to the description later.
√ -
User’s Manual (PDF file)
To use RadiCS LE or ScreenManager Pro for Medical
Refer to the corresponding User's Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable.
For more information refer to the "2-2. Making Use of USB (Universal Serial Bus)" (page 12).

10
2. Installation
2. Installation
2-1. Environmental Settings
Depending upon your operating environment, it may be necessary to set the frequency that corresponds
to your graphics board. If you install it for the first time or change environment, set the monitor.
NOTE
•Factory default settings are for single display mode and Dual Link.
•Use RadiCS/RadiCS LE only in single display mode in landscape orientation. This software cannot be
used with dual display mode or in portrait orientation.
•Refer to the manual of the graphics board.
•These environment described below can be set regardless of whether or not the computer is running.
Displaying Two Screens Simultaneously
It is possible to display two screens on a single monitor at the same time by using one graphics board
with DVI-D2 type output or two graphics boards with DVI-D output on the same computer.
Dual display with 1280 × 1600 resolution is the maximum display size.
How to set
1
Connect the [SIGNAL1] signal input connector and the computer using the
[DD200DL-BK] signal cable.
2
Connect the [SIGNAL2] signal input connector and the computer using the
[FD-C39] signal cable.
After connecting the cable connectors, tighten the screws of the connectors to secure the coupling.
Connectors on the PC Signal cable Connectors on the
monitor
Signal cable (DD200DL-BK) SIGNAL1
Signal cable (FD-C39) SIGNAL2
FD-C39
DD200DL-BK

2. Installation
11
3
Hold down the button and press the button.
4
The <Display Setup> menu will appear in the middle of the screen. Press the
buttons to select "Dual Display" and then press .
Inputting 10 bit Color Signal
Some graphics boards support 10 bit color signal input.
How to set
1
Connect the [SIGNAL1] signal input connector and the computer using the
[DD200DL-BK] signal cable.
After connecting the cable connectors, tighten the screws of the connectors to secure the coupling.
Connectors on the PC Signal cable Connectors on the monitor
Signal cable (DD200DL-BK) SIGNAL1
2
Hold down the button and press the button.
3
The <Display Setup> menu will appear in the middle of the screen. Press the
buttons to select "Single Display" and then press .
4
The <Signal Selection> menu will appear. Press the buttons to select "Single
Link/10bit", and press .

12
2. Installation
2-2. Making Use of USB (Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC
or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily
connected.
Required system environment
•PC equipped with USB ports or another USB hub connected to the USB compliant PC
•Windows 2000/XP/Vista // Mac OS 9.2.2 and Mac OS X 10.2 or later
•USB Cable (MD-C93, enclosed)
NOTE
•The USB hub function may not work properly depending on the PC or peripherals. Please consult the
manufacturer of each device about the USB support.
•Using the USB Rev. 2.0 compatible PC or peripherals is recommended.
•If the monitor is in the power saving mode, or if the monitor is connected to the power outlet with the
monitor turned off, all the devices connected to the USB ports (upstream and downstream) work.
Therefore, power consumption of the monitor varies with connected devices even in the power saving
mode.
•The followings are procedures for the Windows2000/XP/Vista and Mac OS.
Connecting to the USB HUB
1
Connect the monitor to the PC with the signal cable first, then turn on the PC.
2
Connect the upstream port of the monitor to the downstream port of the
USBcompliant PC or another hub by using the USB cable.
After connecting the USB cable, the USB function can be set up automatically.
3
After setting up, the monitor's USB hub is available for connecting USB
compliantperipherals to the downstream ports of the monitor.
Downstream
Upstream

3. Screen Adjustment and Settings
13
3. Screen Adjustment and Settings
3-1. Basic Operation and Functions
ScreenManager allows you to adjust screen performance though the main menu and select a CAL Switch
mode easily.
NOTE
•The Adjustment menu and the CAL Switch menu cannot be displayed at the same time.
1
Entering the ScreenManager
Press once to display the main menu of the ScreenManager.
2
Making Adjustments and Settings
1. Select the desired sub menu icon using and press . The sub menu appears.
2. Use to select the desired setting icon and press . The setting menu appears.
3. Use to make all required adjustments and press save the settings.
3
Exiting the ScreenManager
1. To return to the main menu, select the <Return> icon or press twice, followed by .
2. To exit the ScreenManager, select <Exit> icon or press twice, followed by .
Tips
•Double clicking at any time also exits the ScreenManager menu.
Adjustment menu (ScreenManagaer®)
Mode button Control buttons
(Left, Down, Up, Right)
Power button
Enter button
CAL Switch Menu

14
3. Screen Adjustment and Settings
Functions
The following table shows all the ScreenManager's adjustment and setting menus.
Main menu Sub menu Reference
Setup Mode Preset Setting CAL Switch Mode Display Settings
Input Signal Set the input signal selection of automatic or manual.
Color(Custom)*1Brightness 3-2. Color Adjustment
Temperature
Gamma
Saturation
Hue
Gain
6 Colors
Reset
PowerManager DVI DMPM 3-3. Power-save Setup
OFF
Others Screen Size 3-7. Displaying Lower Resolutions
Smoothing
Border Intensity
Off Timer Set the monitor's Off Timer to on or off.
Menu Settings Menu Size Change the size of the menu.
Menu Position Adjust the menu position.
Menu Off Timer Set the menu displaying time.
Translucent Set the transparency of the background.
Orientation Set the orientation of the Adjustment menu.
Power Indicator Make non-light for blue lighting when the screen is
displayed (Power Indicator Setting).
Reset Return to the factory Default settings.
Information Information Review the ScreenManager's settings, model name,
serial number and usage time.*2
Language English, German, French,
Spanish, Italian, Swedish,
Chinese(Simplified),
Chinese(Traditional) and Japanese
Select the ScreenManager's language.
*1The adjustable functions on the <Color> menu depend on the selected CAL Switch mode. The above table shows the sub
menus when the "Custom" mode is selected (See " 3-2. Color Adjustment ").
*2Due to the inspection on the factory, the usage time may not "0 hour" at shipping.

3. Screen Adjustment and Settings
15
3-2. Color Adjustment
Simple Adjustment [CAL Switch mode]
This function allows you to select the best display mode for monitor brightness, etc.
To select CAL Switch mode
Directly pressing
-/$%
allows you to select the best suited mode for screen display from 4 CAL Switch
modes; DICOM, Custom, CAL, and Text.
Press to exit the menu.
Tips
•The Adjustment menu and the CAL Switch mode name cannot be displayed at the same time.
CAL Switch Mode
Selectable CAL Switch modes are as follows.
Mode Purpose
DICOM Select this option to display images in the DICOM mode.
Custom Available for making desired setting.
CAL Used for monitor calibration
Text Suitable for displaying texts for word processing or spreadsheets.
Color Adjustment of the Mode Settings
<Brightness>, <Temperature> and <Gamma> settings can be adjusted on the CAL Switch menu. Select
the desired function icon with and adjust with . (Setting(s) of <Temperature> and/or
<Gamma> is defined as standard default in some modes.
NOTE
•"DICOM" mode and "CAL" mode can be adjusted only by Calibration Software.
->DICOM -> Custom ->CAL ->Text
Current Mode
Mode button
Power button
CAL Switch Menu
[EX.]Custom
Settings status
of Brightness,
Temperature and
Gamma
Enter button
Control buttons

16
3. Screen Adjustment and Settings
Advanced Adjustments[Adjustment menu]
Color settings of each CAL Switch mode can be adjusted and saved by using the <Color> menu of the
Adjustment menu.
Adjustment Items
The adjustable items and displayed icons on the <Color> menu depend on the selected CAL Switch
mode.
" √": Settable/Adjustable " - ": Fixed at the factory
Icons Functions CAL Switch Mode
DICOM Custom CAL Text
Brightness*√ √ √ √
Temperature*ー√ ー√
Gamma*ー√ ー√
Saturation ー√ ー√
Hue ー√ ー√
Gain ー√ ー ー
6 colors ー√ ー ー
Reset √ √ ー√
*These settings can be also adjusted on the CAL Switch menu. (See CAL Switch.)
NOTE
•Allow the LCD monitor to stabilize for at least 30 minutes before making image adjustments. (Allow
the monitor to warm up for at least 30 minutes before making adjustments.)
•The values shown in percentages represent the current level within the specific adjustment. They
areavailable only as a reference tool. (To create a uniform white or black screen, the percentages for
each will probably not be the same.)

3. Screen Adjustment and Settings
17
Adjustment Contents
Menu Function Descriptions Adjustable range
Brightness To set the brightness of the screen 0~100%
Tips
• The values shown in the “%” are available only as reference.
Temperature To set the color temperature 6000K~15000K
in 500 K increments (including 9300 K)
Tips
• The values shown in the Kelvin are available only as a reference tool.
• While color temperature is adjusted, <Gain> is adjusted automatically according to the
color temperature.
• Setting the temperature under 6000 K or over 15000 K invalidates the color
temperature setting. (The color temperature's setting turns "OFF".)
• Setting the <Gain> invalidates the <Temperature> adjustment.
Gamma To set the gamma value 1.8~2.6
Saturation To change the saturation -100~100
Setting the minimum level (-100) turns the
image to the monochrome.
NOTE
• The <Saturation> adjustment may cause undisplayable color tone.
Hue To change the flesh color, etc. -100~100
NOTE
• Using <Hue> adjustment may not obtain proper tone reproduction.
Gain To change each color
(red, green and blue)
0~100%
By adjusting the red, green and blue color
tones for each mode, custom colors can be
defined. Display a white or gray background
image and adjust the <Gain>.
Tips
• The values shown in the “%” are available only as reference.
• The <Temperature> setting invalidates this setting. The <Gain> setting varies with
color temperature.
6 colors To adjust <Saturation> and <Hue> in
each color (Red, Yellow, Green, Cyan,
Blue and Magenta)
Hue: -100 ~ 100
Saturation: -100 ~ 100
Reset To reset the color settings of the selected CAL Switch mode to the default settings.

18
3. Screen Adjustment and Settings
3-3. Power-save Setup
The <PowerManager> menu in the ScreenManager enables to set the power-save setup.
NOTE
•Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting
the monitor from the power supply is recommended to save energy completely.
•Even if the monitor is in a power saving mode, USB compliant devices function when they are
connected to the monitor's USB (both the upstream and the downstream ports). Therefore, power
consumption of the monitor will change according to the connected devices even if the monitor is in a
power saving mode.
This monitor complies with the "DVI DMPM"
[Procedure]
1. Set the PC's power saving settings.
2. Select "DVI DMPM" from the <PowerManager> menu.
[Power Saving System]
The monitor enters the power saving mode in five seconds in connection with the PC setting.
PC Monitor Power Indicator
Operation Operation Blue
Power saving Power saving Orange
[Power Resumption Procedure]
Operate the mouse or keyboard to return to a normal screen.

3. Screen Adjustment and Settings
19
3-4. Off Timer
The off timer function causes the monitor to automatically enter a power off state after a predetermined
amount of time has lapsed. This function was created to reduce Afterimage characteristics that are
particular to LCD monitors when the monitor screen is left on for a long period without use.
[Procedure]
1. Select <Off Timer> in the ScreenManager <Others> menu.
2. Select "Enable" and touch the Right and Left directing switches to adjust the operating time (1 to 23
hours).
[Off Timer System]
PC Monitor Power Indicator
Operating time (1H - 23H) Operation Blue
Last 15 min. in operating time Advance Notice *1Blue Flashing
Operating time expired Power Off Off
*1 When is pressed during the advance notice period, the monitor continues to operate for additional 90 minutes. Extension
of operation time can be set without limitation.
[Power Resumption Procedure]
Press to return a normal screen.
NOTE
•The off timer function works while the PowerManager is active, but there is no advance notice before
the monitor's power is turned off.
3-5. Locking the Settings
Use the "Adjustment Lock" function to prevent any accidental changes.
Buttons that can be locked • (Enter button) / Adjustments/settings using Adjustment menu
Buttons that cannot be locked • (Input Signal Selection button)
•
-/$%
(Mode button)
•(Power button)
[How to lock]
1. Press to turn off the unit.
2. Press again while pressing
-/$%
.
The screen is displayed with the adjustment lock.
[How to unlock]
1. Press to turn off the unit.
2. Press again while pressing
-/$%
.
The screen is displayed with the adjustment lock released.
NOTE
•The adjustment lock function may activate when calibration is performed with the calibration kit. The
monitor can be unlocked using the same unlocking procedure described above.

20
3. Screen Adjustment and Settings
3-6. Power Indicator Setting
Light off the power indicator. This function is available for the multiple panels settings.
[Procedure]
1. Select <Power Indicator> in the ScreenManager <Others> menu.
2. Select "Disable".
3-7. Displaying Lower Resolutions
The lower resolutions are enlarged to full screen automatically. Using the <Screen Size> function in the
<Others> menu enables to change the screen size.
1
Enlarge the screen size when displaying a low resolution.
Select the <Screen Size>.
Select the <Screen Size> in the <Others> menu and select the screen size by using and .
Mode Function
Full Displays the picture on the screen in full, irrespective of the picture's resolution.
Since the verticalresolution and the horizontal resolution are enlarged at different
rates, some images may appeardistorted.
Enlarged Displays the picture on the screen in full, irrespective of the picture's resolution.
Since the vertical resolution and horizontal resolution are enlarged at same rates,
some horizontal or vertical image maydisappear.
Normal Displays the picture at the actual Screen resolution.
Example: Displaying Image size 1280 × 1024 when setting <Single Display> in <Display Setup>.
2
Smooth the blurred texts of the enlarged screen.
Switch the <Smoothing> setting.
Select the suitable level from 1 - 5 (Soft - Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the right and left switches.
NOTE
•Smoothing setting may not be required depending on the display resolution. (You cannot
choose the smoothing icon.
(2560× 1600) (2000 × 1600) (1280 × 1024)
Full (Default Setting) Enlarged Normal