Eizo RadiForce GX240-CL User manual

Important
Please read PRECAUTIONS, this User’s Manual, and Setup Manual
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Cover
Instructions for Use
■User’s Manual

2
This product has been adjusted specically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior
arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are
subject to change without notice.

3
Notice for this monitor
Notice for this monitor
GX240: This product is intended to be used in displaying and viewing digital images by trained medical practitioners.
It does not support the display of mammography images for diagnosis.
GX340: This product is intended to be used in displaying and viewing digital images for diagnosis of X-ray or MRI,
etc. by trained medical practitioners. The device is not specied for digital mammography system.
Caution: Federal law (USA) restricts this device to sale by or on the order of a physician.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on or the monitor has recovered from the power saving mode.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The screen may have defective pixels or a small number of light dots on the screen. This is due to the characteristics of
the panel itself, and is not a malfunction of the product.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference
patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure
marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.

4Noticeforthismonitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
1-2. EIZO LCD Utility Disk.................................... 7
●Diskcontentsandsoftwareoverview............. 7
●TouseRadiCSLE/ScreenManagerPro
forMedical....................................................... 7
1-3. Basic Operations and Functions ................ 8
●BasicAdjustmentmenuoperations................ 8
●Functions......................................................... 9
Chapter 2 Adjusting Screens .......................... 10
2-1. Compatible Resolutions .............................10
2-2. Setting the Resolution ................................10
●Windows8/Windows7.................................10
●WindowsVista................................................10
●WindowsXP...................................................10
●MacOSX.......................................................10
2-3. Adjusting Mode ............................................11
●Toselectthedisplaymode(CALSwitch
mode).............................................................11
●Adjustablesettingsineachmode..................11
●Toadjustbrightness.......................................12
●Tosetthemodeinthemonochrome
displayarea....................................................12
●Tosetthemodeinthebasedisplayarea......13
●Tosetthedetectiontypeintheimage
displayarea....................................................13
●Tosetthehighlightareaintheimage
displayarea....................................................13
Chapter 3 Setting Monitor ............................... 14
3-1. Setting Orientation ......................................14
3-2. Enabling/Disabling Mode Selection ..........14
3-3. Setting Language .........................................15
3-4. Setting Adjustment Menu Display .............15
●ChangingAdjustmentMenuDisplayPosition15
3-5. Setting the EIZO Logo Display ...................15
3-6. Locking Buttons ...........................................16
3-7. Enabling/Disabling DDC Communication .16
3-8. Enabling/Disabling DC5V Output...............16
3-9. Return To Default Setting............................17
●Toresetthemodeadjustments......................17
●Toresetallsettings........................................17
Chapter 4 Controlling Monitor Quality ........... 18
4-1. Executing Calibration ..................................18
●ExecutingSelfCalibration...............................18
●ViewingSelfCalibrationresult........................18
4-2. Checking Grayscale .....................................19
●ExecutingGrayscaleCheck...........................19
●ViewingGrayscaleCheckresult....................19
4-3. Acquiring Life Prediction Data ...................19
4-4. Setting On/Off for Warning and QC
History .......................................................... 20
Chapter 5 Power Saving Functions ................ 21
5-1. Setting Power Save ......................................21
5-2. Setting Power Indicator ...............................21
5-3. Setting the power saving mode when a
person leaves the monitor ......................... 22
Chapter 6 Troubleshooting .............................. 23
6-1. No picture .................................................... 23
6-2. Imaging problems ....................................... 24
6-3. Other problems ........................................... 25
●ErrorCodeTable........................................... 26
Chapter 7 Reference ........................................ 27
7-1. How to Attach the Arm ............................... 27
7-2. Connecting Multiple PCs ........................... 28
●Toswitchamonginputsignals...................... 28
●Tosetinputsignalselection.......................... 29
7-3. Making Use of USB (Universal Serial
Bus) ............................................................... 30
●Requiredsystemenvironment...................... 30
●Connectionprocedure(SetupofUSB
function)......................................................... 30
7-4. Displaying Monitor Information .................31
●Displayingsignalinformation.........................31
●DisplayingMonitorInformation......................31
7-5. Specications ............................................. 32
7-6. Glossary ....................................................... 36
Appendix .............................................................. 37
Trademark ................................................................37
License .....................................................................37
Medical Standard ................................................... 38
FCC Declaration of Conformity ............................ 39
EMC Information .................................................... 40
LIMITED WARRANTY ............................................. 43
Recycling Information ........................................... 50
China Measures for RoHS Compliance in
ChinaRoHS .............................................................. 54

6Chapter1Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO monochrome LCD monitor.
1-1. Features
• 21.3 inches
• Applicable to the resolution of 2M pixels (Portrait : 1200 × 1600 dots (H × V))(GX240-CL)
• Applicable to the resolution of 3M pixels (Portrait : 1536 × 2048 dots (H × V))(GX340-CL)
• Uses high-contrast panel
Enables the display of sharp images.
- 1400 : 1
• Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals)
• The Hybrid Gamma function automatically identies the display area for the medical and other images on
the same screen, and displays each set status.
*1 The identication may fail depending on the displayed image. The software to be used needs to be veried. For
validation, see “To set the highlight area in the image display area” (page 13).
• The RadiCS SelfQC function and the built-in Integrated Front Sensor allow the user to perform the
calibration and Grayscale Check for the monitor independently.
See “Chapter 4 Controlling Monitor Quality” (page 18)
*2 When a panel protector (RP-903) is installed, the Integrated Front Sensor cannot be used.
• The quality control software “RadiCS LE (for Windows)” used to calibrate the monitor and to manage the
history is included
See “1-2. EIZO LCD Utility Disk” (page 7)
• The software “ScreenManager Pro for Medical” to adjust the screen using the mouse and keyboard is
included
See “1-2. EIZO LCD Utility Disk” (page 7)
• CAL Switch function for selecting an optimal calibration mode
See “To select the display mode (CAL Switch mode)” (page 11)
• Selectable DICOM (page 36) Part 14 complied screen.
• Frame Synchronous mode supported (29.5 to 30.5 Hz (GX340-CL), 59 to 61 Hz)
• Power saving function
This product is equipped with power saving function.
- Power Consumption when main power switch is Off: 0 W
Equipped with main power switch.
Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not used.
- Presence Sensor
The sensor on the front side of the monitor detects the movement of a person. When a person moves away from the
monitor, it shifts to the power saving mode automatically and does not display the images on the screen. Therefore,
the function reduces the power consumption.
See “5-3. Setting the power saving mode when a person leaves the monitor” (page 22)

7
Chapter1Introduction
• Long service life LED backlight LCD panel
• Built-in ambient light sensor
Built-in ambient light sensor measures the environmental illuminance in lux. Depending on the environment, the sensor
sometimes indicates different values from those measured by a stand-alone illuminance meter.
The usage of this sensor requires the quality control software “RadiCS/RadiCS LE” and the measurement is always
triggered by the user’s operation in the corresponding menu.
For further details about the measured value and how to execute the measurement, refer to the RadiCS/RadiCS LE
User’s Manual (on the CD-ROM).
• HDCP (High-bandwidth Digital Content Protection) (DisplayPort only)
Attention
• Storing or using the monitor at a temperature of under 30˚C and a humidity of under 70% is recommended, or it may
affect the measurement accuracy of the built-in sensor. Avoid storing or using the sensor where it may be exposed to
direct sunlight.
1-2. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents
and the overview of the software programs.
●Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to Readme.txt le
on the disk for software startup procedures or le access procedures.
Contents Overview
Readme.txtle
RadiCSLE(forWindows) Qualitycontrolsoftwareforcalibratingthemonitorandmanagingthe
calibrationhistory.
ScreenManagerProforMedical(for
Windows)
Softwareforadjustingthescreenusingthemouseandkeyboard.
User’sManualofthismonitor(PDFle)
●To use RadiCS LE/ScreenManager Pro for Medical
For the installation and use of “RadiCS LE/ScreenManager Pro for Medical”, refer to the respective User’s
Manual on the disk.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable. For more
information, see “7-3. Making Use of USB (Universal Serial Bus)” (page 30).

8Chapter1Introduction
1-3. Basic Operations and Functions
●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The Adjustment menu appears.
Currentmode
Menutitle
Setting
Menu
Item
2.
Adjusting/Setting
1. Choose a menu to adjust/set with , , and then press .
2. Choose an item to adjust/set with , , and then press .
3. Adjust/set the selected item with , , and then press .
3.
Quit
1. Press a few times. The Adjustment menu nishes.

9
Chapter1Introduction
●Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main Menu Item Reference
Mode Brightness “2-3.AdjustingMode”(page11)
GrayArea
BaseArea
HybridAssignment
HighlightArea
ModeReset “3-9.ReturnToDefaultSetting”(page17)
RadiCSSelfQC SelfCalibration “4-1.ExecutingCalibration”(page18)
GrayscaleCheck “4-2.CheckingGrayscale”(page19)
LEA “4-3.AcquiringLifePredictionData”(page19)
Settings “4-4.SettingOn/OffforWarningandQC
History”(page20)
Power
Manager PowerSave “5-1.SettingPowerSave”(page21)
PresenceSensor “5-3.Settingthepowersavingmodewhena
personleavesthemonitor”(page22)
PowerIndicator “5-2.SettingPowerIndicator”(page21)
MenuSettings Language “3-3.SettingLanguage”(page15)
MenuPosition “3-4.SettingAdjustmentMenuDisplay”(page15)
Tools Input “Toswitchamonginputsignals”(page28)
InputSelection “Tosetinputsignalselection”(page29)
ModePreset “3-2.Enabling/DisablingModeSelection”(page
14)
SignalInfo “7-4.DisplayingMonitorInformation”(page31)
MonitorInfo
AllReset “3-9.ReturnToDefaultSetting”(page17)

10 Chapter2AdjustingScreens
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions
For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual.
2-2. Setting the Resolution
●Windows 8 / Windows 7
1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a conrmation dialog box is displayed, click “Keep changes”.
●Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
●Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution
for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
●Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close the
window.

11
Chapter2AdjustingScreens
2-3. Adjusting Mode
●To select the display mode (CAL Switch mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
1-DICOM AvailabletodisplayinDICOMmode.
2-CAL1 Displaysthescreenadjustedbycalibrationsoftware.
3-CAL2
4-Hybrid-γ Automaticallyidentiesthedisplayareaforthemedicalandotherimagesonthesame
screen,anddisplayseachsetstatus.
Themodemenu
appears.
Procedure
1. Press .
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the mode with or while the mode menu is displayed.
→ 1-DICOM←→2-CAL1←→3-CAL2←→4-Hybrid-γ←
Note
• The Adjustment menu and the Mode menu cannot be displayed at the same time.
●Adjustable settings in each mode
The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)
√: Adjustable -: Not adjustable
Icon Function
CAL Switch mode
1-DICOM 2-CAL1
3-CAL2 4-Hybrid-γ
Brightness √ √ -
GrayArea - - √
BaseArea - - √
HybridAssignment - - √
HighlightArea - - √
ModeReset √√√

12 Chapter2AdjustingScreens
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back
panel).
Setting Range
0 to 100%
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Brightness” from “Mode”, and press .
3. Use or for adjustment.
4. Press to exit.
●To set the mode in the monochrome display area
The mode suitable for the monochrome image display area can be set (see “To select the display mode (CAL
Switch mode)” (page 11)).
Setting Range
DICOM, CAL1, CAL2
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Gray Area” from “Mode”, and press .
3. Use or for adjustment.
4. Press to exit.
Attention
• After the conguration in the display area, you cannot select any mode for which Mode Preset is “Off” (see “3-2.
Enabling/Disabling Mode Selection” (page 14)).
Note
• The Brightness is the same as the value for the mode selected. To change the brightness, use the mode selected for
adjustment.

13
Chapter2AdjustingScreens
●To set the mode in the base display area
The mode suitable for the base display area can be set.
Setting Range
Base-L, Base-H
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Base Area” from “Mode”, and press .
3. Select “Base-L” or “Base-H” with or .
Mode Purpose
Base-L Speciesthetargetbrightnessat100cd/m2.
Base-H Speciesthetargetbrightnessto170cd/m2.
4. Press to exit.
Attention
• After the conguration in the display area, you cannot select any mode for which Mode Preset is “Off” (see “3-2.
Enabling/Disabling Mode Selection” (page 14)).
Note
• If the brightness value in the base display area is higher than the target brightness, the target brightness is applied for
Base-L and Base-H.
●To set the detection type in the image display area
You can set the detection type in the display area.
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Hybrid Assignment” from “Mode”, and press .
3. Select “Full Scan”, “Partial Scan”, or “Custom” with or .
Detection
Type
Purpose
FullScan Identiesthedisplayareaautomatically.
PartialScan Identiestheselectionareausingsoftware(HybridGammaManager)automatically.
Custom Allowsyoutosetthedisplayareamanuallyusingsoftware(HybridGammaManager).
4. Press to exit.
Note
• For Hybrid Gamma Manager, contact your local dealer.
●To set the highlight area in the image display area
You can set On/Off for the highlight area in the image display area.
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Highlight Area” from “Mode”, and press .
3. Select “On” or “Off” with or .
4. Press to exit.
Note
• You can set On/Off for the highlight area with .

14 Chapter3SettingMonitor
Chapter 3 Setting Monitor
3-1. Setting Orientation
This function changes the display orientation of the image based on the operating environment.
Attention
• Refer to the User’s Manual of the graphics board.
• Setting is available even when the PC is not started up.
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Orientation” from “Optional Settings”, and press .
4. Choose “Landscape”, “Portrait (SW)”, or “Portrait (HW)” with or , and press .
Monitor Orientation Display Example
Landscape
SelectthisoptionwhenusingtheLandscapeorientation.
A
A
Portrait(SW)
SelectthisoptionwhenusingthePortraitorientation.Graphicsboardutility
softwareisusedtorotatethedisplayimage90degrees.
A
A
Portrait(HW)
SelectthisoptionwhenusingthePortraitorientation.Graphicsboardutility
softwareisusedtorotatethedisplayimage90degrees.
A
A
5. Select “Finish” with or .
6. Press .
The “Optional Settings” menu is closed.
3-2. Enabling/Disabling Mode Selection
Allows you to select the specied modes only.
Use this function when all the display modes are not available or when keeping the display mode unchanged.
Procedure
1. Choose “Tools” from the Adjustment menu, and press .
2. Choose “Mode Preset” from “Tools”, and press .
3. Use or to select the mode to change, and press .
4. Select “On” or “Off” with or .
5. Press to exit.
Attention
• You cannot set all the modes disable. Set at least one mode to “On”.

15
Chapter3SettingMonitor
3-3. Setting Language
This function allows you to select a language for the Adjustment menu and messages.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Japanese/Simplied Chinese/Traditional Chinese
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press .
2. Choose “Language” from “Menu Settings”, and press .
3. Select a language with or .
4. Press to exit.
3-4. Setting Adjustment Menu Display
●Changing Adjustment Menu Display Position
You can change the display position of the Adjustment menu.
Procedure
1. Choose “Menu Settings” from the Adjustment menu, and press .
2. Choose “Menu Position” from “Menu Settings”, and press .
3. Choose the position with or .
4. Press to exit.
3-5. Setting the EIZO Logo Display
This function allows you to display, or not, the EIZO logo.
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Logo” from “Optional Settings”, and press .
4. Select “On” or “Off” with or , and press .
5. Select “Finish” with or .
6. Press .
The “Optional Settings” menu is closed.

16 Chapter3SettingMonitor
3-6. Locking Buttons
This function allows you to lock the adjusted/set status to prevent changing them.
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Key Lock” from “Optional Settings”, and press .
4. Choose “Off”, “Menu”, or “All” with or , and press .
Settings Buttons that can be locked
Off
(Defaultsetting)
None(Allbuttonsareenabled)
Menu button
All Allbuttonsexcluding
5. Select “Finish” with or .
6. Press .
The “Optional Settings” menu is closed.
3-7. Enabling/Disabling DDC Communication
This function allows you to enable/disable the DDC communication. Normally, turn it on during use. (This is
different from the DDC/CI communication.)
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “DDC” from “Optional Settings”, and press .
4. Select “On” or “Off” with or , and press .
5. Select “Finish” with or .
6. Press .
The “Optional Settings” menu is closed.
3-8. Enabling/Disabling DC5V Output
This function allows you to enable/disable the DC5V output. Normally, turn it off during use.
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “DC5V Output” from “Optional Settings”, and press .
4. Select “On” or “Off” with or , and press .
5. Select “Finish” with or .
6. Press .
The “Optional Settings” menu is closed.

17
Chapter3SettingMonitor
3-9. Return To Default Setting
There are two different Resets: Mode Reset for only resetting the mode adjustments to the default settings and All
Reset for resetting all settings to the defaults.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 34).
●To reset the mode adjustments
This function only resets the mode adjustment value for the currently selected mode to the default settings.
Procedure
1. Choose “Mode” from the Adjustment menu, and press .
2. Choose “Mode Reset” from “Mode”, and press .
3. Select “Execute” with or .
4. Press .
The mode adjustments revert to the default settings.
●To reset all settings
This function resets all adjustments to the default settings (except the “Input” and “Optional Settings” menus).
Procedure
1. Choose “Tools” from the Adjustment menu, and press .
2. Choose “All Reset” from “Tools”, and press .
3. Select “Execute” with or .
4. Press .
All settings excluding the “Input” and “Optional Settings” menus are reset to the default settings.

18 Chapter4ControllingMonitorQuality
Chapter 4 Controlling Monitor Quality
This product has the built-in Integrated Front Sensor, which allows the user to perform periodic calibration and
Grayscale Check for the monitor independently.
Attention
• When a panel protector (RP-903) is installed, the Integrated Front Sensor cannot be used. Do not execute “SelfCalibration”
or “Grayscale Check” of “RadiCS SelfQC”. Be sure to set “Meas. Frequency” to “Off”.
• When a panel protector (RP-913) is installed, the Integrated Front Sensor can be used. After installation, be sure to execute
correlation using RadiCS/RadiCS LE.
Note
• To perform advanced quality control that conforms to medical standards, use the optional monitor quality control software
kit “RadiCS UX1”.
• Perform correlation using RadiCS/RadiCS LE to adjust the measurement result of the Integrated Front Sensor to the
measurement result of the UX1 sensor for reference. Periodical correlation enables the measurement accuracy of the
Integrated Front Sensor equivalent to that of the UX1 sensor. For details, refer to RadiCS/RadiCS LE User’s Manual.
• “RadiCS” allows you to set the adjustment target for the calibration and judgment value for Grayscale Check, and also the
schedule for the calibration and Grayscale Check.
• The supplied “RadiCS LE” software also allows you to set the adjustment target and schedule for the calibration. For details,
refer to “RadiCS LE User’s Manual” (on the CD-ROM).
4-1. Executing Calibration
This function allows you to execute SelfCalibration and view the latest result. In addition, when the schedule is set
using RadiCS/RadiCS LE, the next calibration schedule appears.
●Executing SelfCalibration
Attention
• Do not execute this function when a panel protector (RP-903) is installed.
• After SelfCalibration is executed, execute Grayscale Check under the actual temperature of the monitor usage
environment.
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “SelfCalibration” from the “RadiCS SelfQC” menu, and press .
3. Select “Execute” with or .
4. Press to exit.
SelfCalibration is executed.
●Viewing SelfCalibration result
Attention
• The result can be viewed when “QC History” is “On” (see “4-4. Setting On/Off for Warning and QC History” (page 20)).
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “SelfCalibration” from the “RadiCS SelfQC” menu, and press .
3. Select “Result” with or .
4. Select “DICOM”, “CAL1” or “CAL2” with or .
5. Press to exit.
The SelfCalibration result (Max. Error Rate, Last Time, and Error Code) appears.

19
Chapter4ControllingMonitorQuality
4-2. Checking Grayscale
This function allows you to execute Grayscale Check and view the latest result. In addition, when the schedule is
set using RadiCS, the next grayscale check schedule appears.
●Executing Grayscale Check
Attention
• Do not execute this function when a panel protector (RP-903) is installed.
• Execute Grayscale Check under the actual temperature of the monitor usage environment.
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “Grayscale Check” from the “RadiCS SelfQC” menu, and press .
3. Select “Execute” with or .
4. Press to exit.
Grayscale Check is executed.
●Viewing Grayscale Check result
Attention
• The result can be viewed when “QC History” is “On”.
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “Grayscale Check” from the “RadiCS SelfQC” menu, and press .
3. Select “Result” with or .
4. Select “DICOM”, “Custom”, “CAL1” or “CAL2” with or .
5. Press to exit.
Up to the ve latest Grayscale Check results (Passed/Failed/Canceled/ERR) appear.
4-3. Acquiring Life Prediction Data
This function allows you to acquire data necessary to predict the monitor life.
Attention
• When a panel protector (RP-903) is installed, be sure to set “Meas. Frequency” to “Off”.
Note
• Data are collected every 100 hours.
• When you select “Power Save”, data are collected when the mode switches to Power Save or the secondary power off after
the above timing is reached.
• When you select “Routine”, data are saved after the following times have elapsed.
- 500, 1000, 2000, 4000, 7000, 10000, 15000, 20000, 25000, 30000, 35000, 40000, 45000, 50000 hours
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “LEA” from the “RadiCS SelfQC” menu, and press .
3. Select “Meas. Frequency” with or .
4. Select “Power Save”, “Routine”, or “Off” with or .
5. Press to exit.

20 Chapter4ControllingMonitorQuality
4-4. Setting On/Off for Warning and QC History
This function allows you to set On/Off for Warning and QC History when the Grayscale Check result is Failed.
Procedure
1. Choose “RadiCS SelfQC” from the Adjustment menu, and press .
2. Choose “Settings” from the “RadiCS SelfQC” menu, and press .
3. Select “Warning” or “QC History” with or .
4. Select “On” or “Off” with or .
5. Press to exit.