Eizo FlexScan T965 User manual

ENGLISH

2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please
read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result
in moderate injury and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2001 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, or otherwise, without the prior written
permission of Eizo Nanao Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information. Although every effort has been made to
ensure that this manual provides up-to-date information, please note that EIZO
monitor specifications are subject to change without notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics
Standards Association.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager, PowerManager, QuickSet and i·Sound are trademarks of
Eizo Nanao Corporation.
FlexScan, SuperErgoCoat and EIZO are registered trademarks of Eizo Nanao
Corporation.
As an ENERGY STAR® Partner, Eizo Nanao Corporation has determined
that this product meets the ENERGY STAR guidelines for energy efficiency.

CONTENTS 3
ENGLISH
CONTENTS
PRECAUTIONS ............................................................................. 4
1. INTRODUCTION ............................................................................ 8
1-1. Features ....................................................................................................... 8
1-2. Package Contents ........................................................................................ 8
1-3. Controls & Connectors ................................................................................ 9
2. INSTALLATION ............................................................................ 10
2-1. Connecting the monitor to the PC.............................................................. 10
2-2. Getting Ready for Operation ...................................................................... 12
3. SCREEN ADJUSTMENT .............................................................. 13
3-1. How to use the ScreenManager ................................................................ 13
3-2. Color .......................................................................................................... 15
3-3. Fine Contrast ............................................................................................. 17
3-4. Power Save ................................................................................................ 18
3-5. Adjustment Lock ........................................................................................ 19
3-6. Connecting Two PCs to The Monitor .......................................................... 19
4. MAKING USE OF USB (Universal Serial Bus) .......................... 20
5. TROUBLESHOOTING .................................................................. 22
6. CLEANING ................................................................................... 27
7. SPECIFICATIONS ........................................................................ 28
8. GLOSSARY .................................................................................. 30

4PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance. Please read this section and the
caution statements on the monitor (refer to the figure below).
[Location of the Caution Statements]
The equipment must be connected to a grounded main outlet.
Jordet stikkontakt skal benyttes når apparatet tilkobles datanett.
PRECAUTIONS
• If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit can be dangerous.
• Do not dismantle the cabinet or modify the unit.
Dismantling the cabinet or modifying the unit may result in electric shock or
burn.
• Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards.
• Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage. If an object or liquid falls/spills into the cabinet, unplug the unit
immediately. Have the unit checked by a qualified service engineer before
using it again.
WARNING

ENGLISH
PRECAUTIONS 5
OK
OK
• Place the unit on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in injury or
equipment damage. If the unit falls, disconnect the power immediately and
have the unit checked by a qualified service engineer before using it again.
Using a unit after it has been dropped may result in fire or electric shock.
• Set the unit in an appropriate location.
Not doing so may cause damage and could result in fire or electric shock.
* Do not place in outdoors.
* Do not place in the transportation system (ship, aircraft, trains,
automobiles, etc.)
* Do not install in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
• To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
• Use the enclosed power cord and connect to the standard power outlet
of your country. Be sure to remain within the rated voltage of the power
cord.
Not doing so may cause fire or electric shock.
• To disconnect the power cord, grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and
could result in fire or electric shock.
• The equipment must be connected to a grounded main outlet.
Not doing so may cause fire or electric shock.
WARNING

6PRECAUTIONS
• Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire,
electric shock, or other damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* For proper connections of the power cord, be certain to plug the power cord
to the provided unit connector and directly to a wall outlet. Not doing so may
result in fire or electric shock.
• Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it.
Use of a damaged cord may result in fire or electric shock.
• Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
WARNING

ENGLISH
PRECAUTIONS 7
OK
• Handle with care when carrying the unit.
Disconnect the power cord and signal cables and remove the optional unit.
Moving the unit with the cord or the option attached is dangerous. It may result
in injury or equipment damage.
• Do not move it alone. Always work with another person.
Moving it alone may cause lower back pain. Also note that the unit is heavier
at the front than at the rear.
• Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laying down or upside down.
* Do not remove the tilt-swivel stand.
Using the unit in this way block the ventilation slots and prevents proper
airflow, leading to fire or other damage.
• Do not sit on the cabinet or place any heavy objects on the cabinet.
A unit with heavy objects on it may fall or be damaged and result in injury.
• Do not touch the plug with wet hands.
Touching the plug with wet hands is dangerous and can cause electrical
shock.
• Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
• Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
• Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
• If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch for
the safety and the power conservation.
CAUTION

81. INTRODUCTION
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Display Monitor.
1-1. Features
• Fully flat screen CRT
• Horizontal scanning frequency of 30-130 kHz
Vertical scanning frequency of 50-160 Hz
• Support to sRGB standard
•The color restoration circuit that can keep stable brightness and color-tone
for a long period supported
• Fine contrast modes, to adjust the most suitable brightness and contrast of the
screen (See page 17)
• Power saving system and off timer system (See page 18)
• Adjustment lock function, to prevent any accidental changes (See page 19)
• Dual inputs with individual color configuration (See page 19)
• The utility software “ScreenManager Pro for USB” (for Windows) which can
control the monitor from a PC with a mouse or keyboard, is included
(See readme.txt in the CD-ROM).
• USB(Universal Serial Bus) hub supported
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing
or damaged.
• Monitor
• Power Cord
• Signal Cable (MD-C87 or MD-C100)
• User’s Manual
• EIZO Utility Disk
• EIZO USB Cable (MD-C93)
• Quick Reference
• LIMITED WARRANTY
• Please retain the packing materials for future transference.

1. INTRODUCTION 9
ENGLISH
(2)
(7)
(6)(5)
(4)
(3)
1-3. Controls & Connectors
Front
(1) ScreenManager™
(2) USB Port*1with a drop down access lid
Downstream port x 1
(3) BNC/D-SUB Selection Button
(4) AUTO/FINE MODE Button
Push the button lightly: Fine Contrast Mode
Selection button
Push the button for more than 2 seconds:
AUTO-SIZING button
(5) QuickSet™ Control Pad
(Hereinafter “Control Pad”)
(6) Power Indicator
Indicated color Power-on status
Green Power is on (Normal mode)
Flashing Green Power save mode 1
Advance notice of
monitor’s off Timer*2
Yellow Power save mode 2
Flashing Yellow Power save mode with
monitor’s off Timer*2
(7) Power Switch
(8) Power Terminal*3 (with a cover)
Rear
(9) Power Connector
(10) D-Sub Mini 15 Pin Input Connector
(11) BNC Input Connector
(12) USB Port*1
Downstream port x 3
Upstream port x 1
*1See page 20-21 for further details.
*2Regarding the “Off Timer”, see page 18.
*3Power Terminal can be used with an optional
i·Sound Sound Unit.

10 2. INSTALLATION
2. INSTALLATION
2-1. Connecting the monitor to the PC
• Be sure that the power switches of both of the PC and the monitor are OFF.
1. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
• Standard graphics board
• Macintosh
Signal Cable (Enclosed)
Macintosh Adapter (Optional)
Please consult EIZO dealer.
Signal Cable (Enclosed)
Standard graphics board
Video Output Connector
D-Sub mini 15 pin
Macintosh (Blue & White)
Video Output Connector
D-Sub mini 15 pin
Macintosh
Video Output Connector
D-Sub 15 pin

2. INSTALLATION 11
ENGLISH
2. Plug the power cord into the power connector at the rear of the
monitor. Then, plug the other end of the cord into a power outlet.
3. Turn on the monitor first, then the PC.
The monitor’s power indicator will light up (green). The monitor will warm up
briefly, then display an image. Whenever finishing your operation, turn off the
PC and the monitor.
(If an image does not appear, make sure that all connections have been made
properly. Refer to the “TROUBLESHOOTING” (See page 22) for additional
advice).
• Generally, for maximum viewing comfort, position the
monitor slightly below eye level. Staring at the monitor
for prolonged periods can cause eyestrain. Be sure to
take adequate rests.
(A 10-minute rest period each hour is suggested).
• Use the enclosed power cord and connect to the standard
power outlet of your country. Be sure to remain within
the rated voltage of the power cord.
Not doing so may cause in fire or electric shock.
• The equipment must be connected to a grounded main
outlet.
Not doing so may cause in fire or electric shock.
WARNING
WARNING

12 2. INSTALLATION
2-2. Getting Ready for Operation
Try each setting procedure if necessary in the following cases.
1. The display image size and/or position is incorrect
ÆÆ
ÆÆ
ÆPress the AUTO/FINE MODE button on the front panel for
more than 2 seconds.
The AUTO-SIZING function centers the displayed image, aligning the image’s
borders with respect to the monitor frame. In general, press the AUTO/FINE
MODE button whenever changing the graphics card or the resolution p.31), or
when image size and/or position is incorrect.
•Pushing the AUTO/FINE MODE button lightly allows changing of the Fine
Contrast modes.
2. The display area is too large or too small
ÆÆ
ÆÆ
ÆReadjust the refresh rates.
Readjust the preferred refresh rates in accordance with the following look-up-
table. Refer to the PC or graphics card manuals on how to change the refresh
rates.
[The maximum (non-interlaced) vertical refresh rates for the model]
•About Plug & Play of the monitor
When your computer and display support VESA DDC, the suitable resolution
and the refresh rate are set by just plugging your display into the computer
without any manual settings.
When your computer system supports Plug & Play, the Display Information
File is not required except for installing the Color Profile.
3. Further adjustment is required
ÆÆ
ÆÆ
ÆAdjust the screen using the ScreenManager (See page 14).
)zH(etarhserfeRlacitreVmumixaM
084x046006x008867x42014201x08210021x00610821x00610441x02916351x8402
061061061121401796808

3. SCREEN ADJUSTMENT 13
ENGLISH
3. SCREEN ADJUSTMENT
• Allow the monitor to stabilize for at least 30 minutes before making image
adjustments.
3-1. How to use the ScreenManager
Use the control pad on the front panel. The control pad can
be pressed in 5 directions, “Enter”, “Up”, “Down”, “Left”
and “Right”.
1. Entering the ScreenManager
Display the ScreenManager “Main menu” by pressing the “Enter” of the
control pad. Main menu displays the current connector type and frequency of
the input signal.
Up
Down
Left Right
Enter
2. Making Adjustments and Settings
(1) Select the desired icon by using “Up”, “Down”, “Left” and “Right” keys.
(2) Press the “Enter” key to display each adjustment/setting menu or “Sub
menu”.
(3) Make the required adjustments/settings by using the control pad.
(4) To save the adjustments/settings and return to the Main menu, press the
“Enter” key.
3. Exiting the ScreenManager
To exit the ScreenManager, select the “Exit from the “Main menu” and press
the Enter key. Pushing the down arrow key twice goes to the “Exit”
position instantly.
• Leaving the ScreenManager idle for 45 seconds or more will turn the adjustment off
automatically without saving.
• The brightness and contrast can be adjusted by pressing the Up, Down, Left and
Right keys of the control pad directly. Press the center of the control pad to save
and exit the settings after the adjustment.
Main menu
Æ

14 3. SCREEN ADJUSTMENT
Main menu Sub menu Adjustments and Settings See page
Contrast — Screen contrast and brightness —
Size — Screen size —
Position — Screen position —
Screen Side Pin Side pin balance —
Trapezoidal Distortion —
Tilt Inclination —
Uniformity Uniformity p.31) p. 24
Convergence Convergence p.30) p. 24
Moiré Reduction Moiré p.30) p. 23
Fine Contrast To select Movie Mode Settings (1~4) p. 17
Signal Filter 1 To decrease the slightly shadowed
images or characters p. 23
Signal Filter 2 To decrease the vertical bars p. 23
Color Color Mode To select the adjustment mode from
standard, custom or sRGB p. 15
•Standard p. 15
Temperature To set the color temperature p.30) p. 15
Color Correction To eliminate disparities in color
temperature and brightness due to
an irregular video signal output p. 15
Color Restoration To restore the changed brightness and
the color caused by long use to close
to those original ones p. 16
•Custom To adjust each color,
(Red, Green and Blue) p. 16
•sRGB To select sRGB Mode p.31) p. 16
Others PowerManager To set the power save
(with PC’s power saving system) p. 18
Off Timer To set the power save
(with Monitor’s off timer) p. 18
Degauss To degauss P.31) p. 24
Beep To set beeper on/off. —
Menu Position To adjust the menu position of
the ScreenManager —
Language To select the preferred language to use —
Input Priority To select the priority input signal p. 19
Reset To return to the factory default setting p. 28
Information — To know the total usage time and
the signal frequency —
Adjustments and Settings

3. SCREEN ADJUSTMENT 15
ENGLISH
3-2. Color
By using the <Color Mode> in the <Color> menu, the adjustment mode can be
selected from standard mode (to set the color temperature, the color correction and
the color restration), custom mode (to adjust each color tone, (Red, Green and Blue))
and sRGB mode. These modes allow you to adjust the color settings according to
your preference.
<Standard> mode to set the color temperature, the color correction
and the color restration
(1) To set the color temperature
ÆÆ
ÆÆ
ÆSet the <Temperature>.
Temperature can be set from 4,000 K to 10,000 K, in 500 K increments.
(Including the 9,300 K default setting.)
(2) To eliminate disparities in color temperature and brightness due
to an irregular video signal output
ÆÆ
ÆÆ
ÆExecute the <Color Correction>.
Color Correction corrects irregular video signal output levels to eliminate
disparities in color temperature and brightness. Every time the PC
(graphics board) and input signal change, execute color correction.
(1) Open a www browser and the Pattern.html in the EIZO Utility Disk.
Then, maximize the window.
(2) Execute the <Color Correction>. All other adjustments are off during
the correction. (The operation takes about 20 to 30 seconds. Do not
change the “Pattern” during the correction.) When color correction is
complete, the result is displayed.

16 3. SCREEN ADJUSTMENT
(3) To restore the changed brightness and the color caused by long
use to close to those original ones.
ÆÆ
ÆÆ
ÆExecute the <Color Restoration>.
The changed brightness and the color caused by long use can be corrected
and restored to close to those factory default settings. Execute this function
in every fixed time (ex. 2000 hours usage), so that you can keep stable
brightness and color-tone for a long period.
(1) Execute the <Color Restoration>. All other adjustments are off during
the correction. (The operation takes about one minute. Do not change
the “Pattern” during the correction.) When color restoration is complete,
the result is displayed.
• Allow the monitor to stabilize for at least 75 minutes before executing this
function. Otherwise, the warning message “Warming Up!” will appear on
the screen.
• The total usage time (in hour) can be checked as the <Information> in the
main menu. Every time the “Enter” of the control pad is pressed, the total
usage time and the signal frequency will be displayed by turns.
<Custom> mode to adjust each color tone (Red, Green and Blue)
ÆÆ
ÆÆ
ÆAdjust the <Gain>p.30) and <Cut off>p.30).
Change the <Color Mode> to <Custom>. The values shown in percentages (%)
for both the Cutoff and Gain are available only as a reference tool.
[Adjustment Procedure]
(1) First, set the monitor to maximum contrast and brightness.
(2) <Temperature> Set the color temperature that is close to the desired color.
(3) Adjust each color to become a uniform black level by using the <Cutoff>
function.
(4) Adjust each color to the desired white level by using the <Gain> function.
(5) Select <Save> and then press the Enter key.
(The adjustment data will be lost, if the monitor is turned off without saving
changes).
<sRGB> mode to select sRGB mode
During selecting the <sRGB>, color, brightness and contrast can not be adjusted.
Likewise, Fine Contrast Mode can not be changed by the AUTO/FINE MODE
button.

3. SCREEN ADJUSTMENT 17
ENGLISH
3-3. Fine Contrast
The fine contrast modes differ in brightness and contrast settings. Select the mode
that is the best suited to the application in use. The mode can be changed with the
AUTO/FINE MODE button that is on the front of the monitor.
To select the most suitable brightness mode
ÆÆ
ÆÆ
ÆPush AUTO/FINE MODE button lightly.
Select from the following modes to adjust the most suitable brightness of the
screen. Pushing this button displays the fine contrast modes in the following
order. (TextÆBrowserÆPictureÆGraphicÆMovieÆText...)
Mode Suitable for
Text • Text on word processor or spreadsheet software
Browser • Text and picture image (ex. home page)
Picture • Photo or picture image (Contrast is enhanced.)
Graphic • Animation or illustration (Contrast is not enhanced.)
Movie*1 • Animated images (games, DVDs)
• Still images that are dark
• When changing the mode or adjusting the contrast, the brightness of the screen
might change for a split second.
• The color temperature and the brightness can be set in the each mode.
•*1There are 4 kinds of movie mode settings. Set the mode by using the <Fine
Contrast> in the <Screen> menu (Refer to the following section for details).
To change the movie mode settings
ÆÆ
ÆÆ
ÆSet the <Movie Mode> of the <Fine Contrast>
Select a mode from the following 4 options when adjusting the contrast or the
sharpness settings.
Set the mode by using the <Fine Contrast> in the <Screen> menu.
Movie Enhanced Enhanced Suitable for
Mode contrast*2 sharpness
1 ON ON DVDs and TV with full-screen
2 ON OFF DVDs and TV with default screen
3 OFF ON When the brightness or sharpness of the
4 OFF OFF input images has been already compensated
*2To display clear images, the monitor checks the input signal then corrects the
mid-range color tone and futher adjusts contrast.

18 3. SCREEN ADJUSTMENT
3-4. Power Save
There are two power save settings. Choose the setting which matches your
environment.
Set the power saving setting by using <Others> menu.
• Do your part to conserve energy, turn off the monitor when you are finished using
it. Complete energy use can only be accomplished by disconnecting the monitor’s
power supply cord from the plug receptacle.
To use the PC’s power saving system (VESA DPMSp.31))
ÆÆ
ÆÆ
ÆSelect “ON” in the <PowerManager> menu.
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “ON” in the <PowerManager> menu.
[Power saving system]
PC Signal Screen LED
ON Operation Green
STAND-BY Blank screen Green
SUSPEND Power save (Mode 1) Flashing green
OFF Power save (Mode 2) Yellow
To use the Monitor’s off timer system
ÆÆ
ÆÆ
ÆSelect “ON” in the <Off Timer> menu.
Without the PC’s power saving system, the off timer allows the monitor to enter
a powersave mode after a predetermined amount of time has lapsed.
[Procedure]
Select “ON” and press the left/right keys on the control pad to set the “On
period”. (1 to 23 hours)
Press any direction of the control pad or to turn the power off then on again to
return to a normal screen.
[Power saving system]
Time Screen LED
On period (1-23H) Operation Green
Last 15 min. in“On period” Advance notice* Flashing green
“On period” expired Power save mode Flashing yellow
* To delay entering the power save mode, press any direction of the control pad
during the advance notice mode. The monitor will continue to operate for an
additional 90 minutes.

3. SCREEN ADJUSTMENT 19
ENGLISH
MD-C53A (Optional)
Apple Macintosh
(Blue & White)
Standard graphics board
Æ
3-5. Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function • Adjustments and settings in the ScreenManager.
• AUTO/FINE MODE button.
Unlocked function • Adjustment of contrast and brightness by the shortcut keys.
• BNC/D-Sub Selection button.
[To lock]
Press on the AUTO/FINE MODE button while switching on the monitor’s power.
[To unlock]
Switch off the monitor’s power, then hold down the AUTO/FINE MODE button
once again and turn the power back on.
3-6. Connecting two PCs to the Monitor
Two PCs can be connected to the monitor through the BNC/D-Sub input connections
on the back of the monitor.
(Example)
Selecting the active input
Every time the BNC/D-Sub selection button is pressed, the input changes in
order.
[Automatically selecting the priority input signal for screen]
The monitor will automatically detect the inputted signal of either the BNC or
D-SUB connection for display. In the following cases, the signal given
preference will be displayed automatically.
• When the monitor is turned on.
• Once a priority is selected in the <Input Priority> function, whenever a
change of signal is detected at the selected input, the monitor will switch the
input to that signal.
(How to give priority to the input)
(1) Select <Input Priority> in the <Others> menu.
(2) Select <Auto> and set BNC or D-SUB input.
Saving the adjustment data
The adjustment data can be saved for both signals. However, the following
adjustment and setting data can be saved for each input signal (BNC/D-Sub).
<Contrast>, <Fine Contrast>, <Temperature>, <Custom>, <sRGB>,
<Signal Filter 1>, <Signal Filter 2> and <Color Correction>

20 4. MAKING USE OF USB (Universal Serial Bus)
4. MAKING USE OF USB
(Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to
a USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
As an added advantage, the monitor can be controlled from a PC with a mouse or
keyboard when utilizing the enclosed utility software “ScreenManager Pro for USB”.
Required system environment
• PC equipped with USB ports or another USB hub connected to the USB compliant
PC
• Windows 98/Me/2000 // Mac OS 8.5.1 or later
• USB cable
• The USB hub function may not work properly depending on the PC, OS or
peripherals. Please consult the manufacturer of each device about the USB
support.
• When the monitor is not on, the peripherals connected to the downstream ports
will not operate.
• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.
Connecting to the USB HUB (Setting up the USB function)
• Do not connect the downstream port of the monitor to any peripherals until
finishing the USB function.
• The followings are procedures for the Windows 98/Me/2000 and Mac OS.
1. Connect the monitor to the PC with the signal cable (See page 10) first, then
turn on the PC.
2. Connect the upstream port of the monitor to the downstream port of the USB
compliant PC or another hub by using the USB cable .
After connecting the USB cable, the USB function can be set up automatically.
Upstream port:
Connect the USB
compliant PC or another
hub using the USB
cable.