Eizo RadiForce RX320 User manual

Important
Please read this User’s Manual carefully to familiarize yourself with safe and effective
usage. Please retain this manual for future reference.
Wichtig
Bitte lesen Sie dieses Benutzerhandbuch sorgfältig durch, um sich mit der sicheren und
effizienten Bedienung vertraut zu machen. Bewahren Sie das vorliegende Handbuch
zu Referenzzwecken auf.
Important
Lisez attentivement le Manuel d’installation afin de vous familiariser avec la sécurité et
un usage effectif. Veuillez conserver ce manuel pour référence ultérieure.
重要
请仔细阅读用户指南，熟练掌握安全和有效的使用方法。
请妥善保存此手册，供日后参考。
重要
ご使用前には必ず取扱説明書をよくお読みになり、正しくお使いください。
この取扱説明書は大切に保管してください。

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: [phone]
declare that the product Trade name: EIZO
Model: RadiForce RX320
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Note
Use the attached specied cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (Enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

It shall be assured that the final system is in compliance to IEC60601-1-1
requirements.
English

2
SAFETY SYMBOLS
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate
injury and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or
result in malfunction of the monitor. Install the equipment in a controlled environment, where
such effects are avoided.
• This is a monitor intended for use in a medical image system. It does not support the display
of mammography images for diagnosis.
• Product specifications may vary depending on the region. Confirm the specifications in the
manual written in the language of the region of purchase.
Copyright© 2009 EIZO NANAO CORPORATION All rights reserved. No part of this manual
may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO
CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor specifications
are subject to change without notice.
Apple and Macintosh are registered trademarks of Apple Inc.
VGA is a registered trademark of International Business Machines Corporation.
VESA is a registered trademark or a trademark of Video Electronics Standards Association in
the United States and other countries.
Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United
States and other countries.
PowerManager, RadiCS and RadiNET are trademarks of EIZO NANAO CORPORATION.
ScreenManager, RadiForce and EIZO are registered trademarks of EIZO NANAO
CORPORATION in Japan and other countries.

TABLE OF CONTENTS
3
TABLE OF CONTENTS
APPENDIX ....................................................................................................................................i
TABLE OF CONTENTS............................................................................................................... 3
PRECAUTIONS ..................................................................................................................... 4
Notice for this monitor.................................................................................................................. 8
1. Introduction............................................................................................................................ 10
1-1. Features ................................................................................................................................... 10
1-2. Package Contents .................................................................................................................... 10
1-3. Controls and Connectors ......................................................................................................... 11
2. Cable Connection ................................................................................................................. 13
2-1. Before Connecting.................................................................................................................... 13
2-2. Single Link Cable Connection .................................................................................................. 14
2-3. Dual Link Cable Connection..................................................................................................... 17
2-4. 10bit Color Signal Input............................................................................................................ 20
3. Adjustment and Settings........................................................................................................ 21
3-1. How to use the ScreenManager............................................................................................... 21
3-2. ScreenManager menu.............................................................................................................. 22
3-3. Color Adjustment...................................................................................................................... 23
3-4. Mode Preset Function <Setup>-<Mode Preset>...................................................................... 26
3-5. Power Saving Function <PowerManager> ............................................................................... 26
3-6. Off Timer <Others>-<Off Timer> .............................................................................................. 27
3-7. Adjustment Lock Function........................................................................................................ 27
3-8. Power Indicator Function <Others>-<Power Indicator >........................................................... 28
3-9. Displaying Low Resolutions ..................................................................................................... 28
4. Making Use of USB (Universal Serial Bus) ........................................................................... 30
5. Attaching an Arm ................................................................................................................... 32
6. Troubleshooting...................................................................................................................... 33
7. Specifications......................................................................................................................... 35
8. Glossary ................................................................................................................................ 39
English

4
PRECAUTIONS
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was originally
shipped. If operated outside the region to which it was originally shipped, the product
may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
[Symbols on the unit]
Symbol This symbol indicates
Main Power Switch
Press to turn the monitor’s main power off.
Main Power Switch
Press to turn the monitor’s main power on.
Power Button
Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
Caution
Refer to SAFETY SYMBOLS section in this manual.

PRECAUTIONS
5
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange
noises, disconnect all power connections immediately and contact your dealer for
advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment
damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock,
or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in
fire, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the
cabinet or spillage into the cabinet may result in fire, electric shock, or
equipment damage. If an object or liquid falls/spills into the cabinet, unplug
the unit immediately. Have the unit checked by a qualified service engineer
before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or
equipment damage. If the unit falls, disconnect the power immediately and
ask your dealer for advice. Do not continue using a damaged unit. Using a
damaged unit may result in fire or electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
• Do not place outdoors.
• Do not place in the transportation system (ship, aircraft, trains,
automobiles, etc.)
• Do not place in a dusty or humid environment.
• Do not place in a location where water is splashed on the screen
(bathroom, kitchen, etc.).
• Do not place in a location where the steam comes directly on the screen.
• Do not place near heat generating devices or a humidifier.
• Do not place in an inflammable gas environment.
To avoid danger of suffocation, keep the plastic packing bags away from babies and
children.
English

6
PRECAUTIONS
WARNING
Use the enclosed power cord and connect to the standard power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
Power supply: 100-120/200-240 Vac 50/60Hz
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Use the correct voltage.
• The unit is designed for use with a specific voltage only. Connection to another voltage than
specified in this Use’s Manual may cause fire, electric shock, or equipment damage.
Power supply: 100-120/200-240 Vac 50/60Hz
• Do not overload your power circuit, as this may result in fire or electric shock.
Handle the power cord with care.
• Do not place the cord underneath the unit or other heavy objects.
• Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock
For the electrical safety, do not connect or disconnect the power cord in the presence
of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user's manual of the arm stand and
install the unit securely.
Not doing so may cause the unit to come unattached, which may result in injury or equipment
damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a
damaged unit. Using a damaged unit may result in fire or electric shock. When reattaching the
tilt stand, please use the same screws and tighten them securely.

PRECAUTIONS
7
WARNING
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the
eyes or mouth.
If any part of the skin or body comes in direct contact with the panel,
please wash thoroughly. If some physical symptoms result, please consult
your doctor.
Fluorescent backlight lamps contain mercury (the products that have LED backlight
lamps contain no mercury), dispose according to local, state or federal laws.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the cord
attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
• Do not place any objects on the ventilation slots.
• Do not install the unit in a closed space.
• Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period, disconnect the power cord
from the wall socket after turning off the power switch for the safety and the power
conservation.
English

8
Notice for this monitor
Notice for this monitor
• This product is suited to display medical images of such modalities as MRI and CT. It does
not support the display of mammography images for diagnosis.
• This product has been adjusted specifically for use in the region to which it was originally
shipped. If the product is used outside the region, it may not operate as specified in the
specifications.
• This product may not be covered by warranty for uses other than those described in this
manual.
• The specifications noted in this manual are only applicable for power cords and signal cables
specified by us.
• Use optional products manufactured or specified by us with this product.
• As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the
monitor 30 minutes or more after the monitor power has been turned on.
• When the screen image is changed after displaying the same image for extended periods of
time, an afterimage may appear. Use the screen saver or timer to avoid displaying the same
image for extended periods of time.
• Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime. (Refer to "Cleaning" on the next page.)
• The screen may have defective pixels. These pixels may appear as slightly light or dark area
on the screen. This is due to the characteristics of the panel itself, and not the product.
• The backlight of the LCD panel has a fixed life span. When the screen becomes dark or
begins to flicker, please contact your dealer.
• Do not press on the panel or edge of the frame strongly, as this may result in the display
malfunction, such as the interference patterns, etc. If pressure is continually applied to the
LCD panel, it may deteriorate or damage your LCD panel. (If the pressure marks remain on
the LCD panel, leave the monitor with a white or black screen. The symptom may disappear.)
• Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this
may result in damage to the panel. Do not attempt to brush with tissues as this may scratch
the LCD panel.
• When the monitor is cold and brought into a room or the room temperature goes up quickly,
dew condensation may occur inside and outside the monitor. In that case, do not turn the
monitor on and wait until dew condensation disappears, otherwise it may cause some
damages to the monitor.

Notice for this monitor
9
Cleaning
NOTE
•
Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, disinfectant,
and abrasive cleaner, which may damage the cabinet or LCD panel.
[LCD Panel]
•The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
•Remove persistent stains gently with a cloth dampened with little water, and then
clean the LCD panel again with a dry cloth for better finishing.
Tips
•Optional ScreenCleaner is recommended for cleaning the panel surface.
[Cabinet]
•To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to
the manual of the PC.)
To use the monitor comfortably
•An excessively dark or bright screen may affect your eyes. Adjust the brightness of the
monitor according to the environmental conditions.
•Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every
hour.
English

10
1. Introduction
1. Introduction
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
•DVI (p.39) digital input (TMDS (p.40)) compliant
•Horizontal scan frequency 31 - 127 kHz
•Vertical scan frequency 59 - 61 Hz
(VGA text: 69 - 71 Hz , QXGA: 29– 61 Hz)
•Frame synchronous mode 59 - 61 Hz supported
•Resolution 3M pixels (Portrait: 1536 × 2048 dots (H × V))
•CAL Switch function for selecting an optimal calibration mode (p. 23)
•Selectable DICOM (p. 39) Part 14 complied screen
•USB (Universal Serial Bus) hub support (p. 30)
•The quality control software “RadiCS LE” (for Windows) used to calibrate the
monitor is included (refer to the EIZO LCD Utility Disk).
•The utility software “ScreenManager Pro for Medical” (for Windows) to control the
monitor from a PC with mouse/keyboard is included (refer to the EIZO LCD Utility
Disk).
•The height adjustable stand incorporated
•Slim bezel
•Dual Link connection support (p.17)
•Signal cable for Dual Link connection supplied
•10bit color signal input support (p.20)
NOTE
•Only designated frequencies are supported for horizontal and vertical scanning.
•Before a 10bit color signal can be input, your graphics board must configured. For
details, refer to the user's manual for the graphics board.
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
•LCD Monitor*1•EIZO LCD Utility Disk
•Power Cord •User’s Manual
•Signal Cable (DD200DL-BK) •LIMITED WARRANTY
•EIZO USB Cable (MD-C93) •Recycling Information
*1 The landscape position is the default monitor orientation. For the portrait position, rotate the monitor ninety
degrees clockwise before installing it.
Tips
•Please retain the packing materials for future transport of the monitor.

1. Introduction
11
1-3. Controls and Connectors
Front
(1) Mode Switch Displays the CAL Switch menu (p. 23).
(2) Enter Switch Displays the ScreenManager menu, determines an item on the
menu screen, and saves values adjusted.
(3) Directing Switches*1
(Left, Down, Up, Right)
Chooses an adjustment item or increases/decreases adjusted
values for advanced adjustments using the ScreenManager menu.
(p. 21)
(4) Power Switch Turns the power on or off.
(5) Power indicator*2Indicates monitor’s operation status
Green:
Orange:
Flashing orange slowly:
Off:
Operational
Power saving
Power off (Main Power is on)
Main Power off
*1 When the monitor is oriented in the landscape position, these switches can be changed to Down, Right,
Left, and Up.
*2 To disable the power indicator while the monitor is operational, see p. 28. For power indicator status
when using the “Off Timer,” see p.27.
ScreenManager ®
main menu
CAL Switch menu Control Panel
English

12
1. Introduction
Rear
(6) Stand*3 Used to adjust the height and angle of the monitor screen.
(7) Security lock slot Allows for connection of a security cable.
This lock supports Kensington’s MicroSavere security system.
(8) USB port (Down) Connects a peripheral USB device.
(9) USB port (Up) Connects the USB cable in order to use the provided software.
(10) Input signal connector DVI-D Connector
*3 The LCD monitor can be oriented in the landscape position. (It can rotate counter-clockwise ninety degrees.)
The LCD monitor can be used with an optional arm stand by removing the stand. (p. 32)
Power connector
Main Power Switch

2. Cable Connection
13
2. Cable Connection
2-1. Before Connecting
• The procedure for connecting the monitor differs depending on the connection method
chosen (Single Link or Dual Link). Verify the graphics board and connection method,
and then perform the appropriate connection steps. Refer to Web site of EIZO NANAO
CORPORATION for the latest information about supported graphics card
(http://www.eizo.com).
• Before connecting your monitor to the PC, change the display screen settings (resolution
(p.39) and frequency) in accordance with the charts below.
Tips
•When your computer and monitor support VESA DDC, the appropriate resolution and
the refresh rate are set just by plugging your display into the computer without any
manual settings.
Single Link Connection
“ √”: Supported
Resolution Frequency Dot Clock Display Mode
Portrait Landscape
640 x 480 Industry Standard 60 Hz 165 MHz
(Max.)
√ √
720 x 400 VGA TEXT 70 Hz √ √
800 x 600 VESA Standard 60 Hz √ √
1024 x 768 VESA Guidelines 60 Hz √ √
1280 x 1024 VESA Standard 60 Hz √ √
1536 x 2048 VESA CVT 30 Hz √ -
1536 x 2048 VESA CVT RB 46 Hz √ -
1600 x 1200 VESA Standard 60 Hz - √
2048 x 1536 VESA CVT 30 Hz - √
2048 x 1536 VESA CVT RB 47 Hz - √
Dual Link Connection
“ √”: Supported
Resolution Frequency Dot Clock Display Mode
Portrait Landscape
640 x 480 Industry Standard 60 Hz 215 MHz
(Max.)
√ √
720 x 400 VGA TEXT 70 Hz √ √
800 x 600 VESA Standard 60 Hz √ √
1024 x 768 VESA Guidelines 60 Hz √ √
1280 x 1024 VESA Standard 60 Hz √ √
1536 x 2048 VESA CVT 30 Hz √ -
1536 x 2048 VESA CVT RB ~60 Hz √ -
1600 x 1200 VESA Standard 60 Hz - √
2048 x 1536 VESA CVT 30 Hz - √
2048 x 1536 VESA CVT RB ~60 Hz - √
English

14
2. Cable Connection
2-2. Single Link Cable Connection
NOTE
•Be sure that the power switches of both the PC and the monitor are OFF.
•Refer to the PC user's manual when connecting the monitor.
•Before a 10bit color signal can be input, your graphics board must configured. For
details, refer to the user's manual for the graphics board.
1
Rotate the monitor ninety degrees clockwise into the portrait position.
2
Connect the signal cable to the DVI-D input connector on the rear of
the monitor and to the video output connector on the PC.
After connecting, secure the cable connectors with the attached screw-in fasteners.
Signal Cable Connector on PC PC
Signal cable (DD200DL-BK) Video Output Connector / DVI Exclusive graphics board
3
Connect the power cord to the power connector on the rear of the
monitor.
Signal cable
DD200DL-BK
Power cord

2. Cable Connection
15
4
Thread the power cord and signal cable through the cable holder on
the rear of the monitor stand.
NOTE
•When threading the cables through the cable holder, lead them to the cable
entrance side and pinch the projection to open the cable entrance.
•It is recommended that some slack be left in the cables to allow for smooth
adjustment of the monitor stand and easy rotation between the portrait and
landscape positions.
5
Connect the other end of the power cord to a power outlet.
WARNING
Use the enclosed power cord and connect to the standard power
outlet of your country.
Be sure to remain within the rated voltage of the power cord. Not do-
ing so may result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
6
Turn on the monitor's power by touching the power switch.
The monitor’s power indicator will light up green.
Cable holder
English

16
2. Cable Connection
7
Turn on the PC’s power.
The image will appear.
If an image does not appear, refer to “6. Troubleshooting” (p. 33) for additional
advice.
When finished, turn off the PC and the monitor.
Tips
•Adjust the brightness of the screen depending on the brightness of your
environment.
•Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
8
When using the software “RadiCS LE” (for Windows) or
“ScreenManager Pro for Medical” (for Windows) connect the monitor
to a USB compliant Windows computer (or other USB hub) with a
USB cable.
Refer to “4. Making Use of USB (Universal Serial Bus)” (p. 30).

2. Cable Connection
17
2-3. Dual Link Cable Connection
NOTE
•Be sure that the power switches of both the PC and the monitor are OFF.
•Refer also to the PC user's manual when connecting the monitor.
1
Rotate the monitor ninety degrees clockwise into the portrait position.
2
Connect the signal cable to the DVI-D input connector on the rear of
the monitor and to the video output connector on the PC.
After connecting, secure the cable connectors with the attached screw-in fasteners.
Signal Cable Connector on PC PC
Signal cable (DD200DL-BK) Video Output Connector / DVI Exclusive graphics board
3
Connect the power cord to the power connector on the rear of the
monitor.
Signal cable
DD200DL-BK
Power cord
English

18
2. Cable Connection
4
Thread the power cord and signal cable through the cable holder on
the rear of the monitor stand.
NOTE
•When threading the cables through the cable holder, lead them to the cable
entrance side and pinch the projection to open the cable entrance.
•It is recommended that some slack be left in the cables to allow for smooth
adjustment of the monitor stand and easy rotation between the portrait and
landscape positions.
5
Connect the other end of the power cord to a power outlet.
WARNING
Use the enclosed power cord and connect to the standard power
outlet of your country.
Be sure to remain within the rated voltage of the power cord. Not do-
ing so may result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Cable holder