Eizo ColorEdge CG247X User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
•Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.
•The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
Color Management LCD Monitor
User’s Manual
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Eizo ColorEdge
CG247X o cerca il tuo prodotto tra le migliori offerte di Monitor

2
Location of Caution Statement
AVERTISSEMENT
WARNING
WARNUNG
This product has been adjusted specically for use in the region to which it was originally shipped.
If operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for this monitor
Notice for this monitor
Aside from general purposes like creating documents and viewing multimedia content, this product is also
suited to applications such as creating images and graphics, and digital photo processing, where accurate
color reproduction is a priority.
This product has been adjusted specically for use in the region to which it was originally shipped.
If the product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 3 minutes (under our measurement conditions) for the performance of electrical parts to
stabilize. Please wait 3 minutes or more after the monitor power has been turned on, and then adjust the
monitor. It is necessary to wait at least 30 minutes after turning on the power, in order to obtain correct
measurement results.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image
for extended periods of time.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear.
To maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime
(refer to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as
interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your
panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen.
The symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel.
Do not attempt to brush with tissues as this may scratch the panel.

4Notice for this monitor
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to
the monitor.
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
The stains on the cabinet and panel surface can be removed by using the provided ScreenCleaner.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
Contents
Contents
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably............................. 4
Contents................................................................. 5
Chapter 1 Introduction....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 9
●Front ................................................................ 9
●Rear ................................................................10
1-3. EIZO LCD Utility Disk...................................11
●Disk contents ..................................................11
●To use ColorNavigator 6 ................................11
1-4. Basic Operations and Functions ...............12
●Basic Adjustment menu operations ...............12
●Functions ........................................................13
Chapter 2 Adjusting Screens .......................... 15
2-1. Setting Resolution.......................................15
●Compatible Resolutions/Formats ...................15
●To switch signal formats (Only for
DisplayPort or HDMI signal input) ..................16
●To set the display resolution for the OS .........16
●To select screen size ......................................17
2-2. Selecting the display mode
(color mode)..................................................19
2-3. Adjusting the Color..................................... 20
●To adjust brightness ...................................... 20
●To adjust the temperature ..............................21
●To adjust gamma ........................................... 22
●To set color gamut ......................................... 22
●To perform advanced adjustments ............... 23
2-4. Specifying Color Space ............................. 26
2-5. Expanding Signal Output Range .............. 27
2-6. Setting HDMI................................................ 28
●To reduce noise ............................................. 28
●To select how to display interlace signal ....... 28
●To set safe area ............................................. 29
Chapter 3 Setting the Monitor......................... 30
3-1. Setting Adjustment Menu .......................... 30
●Selecting the Language ................................ 30
●Setting Orientation ........................................ 30
●To change adjustment menu display
position ...........................................................31
3-2. Skipping Unused Display Modes...............31
3-3. Showing and Hiding the EIZO Logo ..........31
3-4. Locking Operation Buttons ....................... 32
3-5. Changing DUE (Digital Uniformity
Equalizer) Setting ....................................... 32
3-6. Reset to default ........................................... 33
●Resetting the color adjustments ................... 33
●Resetting all adjustments to defaults ............ 33
Chapter 4 SelfCalibration ................................ 34
4-1. Setting the Color Mode for Executing
SelfCalibration ............................................ 34
●CAL mode ..................................................... 34
●Standard Mode .............................................. 35
4-2. Setting Monitor Date and Time.................. 35
4-3. Setting Calibration Schedule .................... 36
4-4. Setting the calibration targets .................. 38
4-5. Executing SelfCalibration.......................... 39
4-6. Checking Adjustment Results................... 40
●To check adjustment results with
CAL mode ..................................................... 40
●To check adjustment results with
Standard Mode .............................................. 40
Chapter 5 Connecting Multiple
External Devices............................. 41
5-1. Switching among Input Signals ................ 42
5-2. Setting Input Signal Switching
Procedure .................................................... 42
5-3. Skipping Unused Input Signals................. 42
5-4. Switching USB Port Automatically........... 43
Chapter 6 Power Saving Functions ................ 44
6-1. Setting Power Save..................................... 44
6-2. Adjusting Brightness of Front Button...... 45
6-3. Setting DisplayPort Power Save ............... 45
Chapter 7 Troubleshooting.............................. 46
7-1. No picture .................................................... 46
7-2. Imaging problems........................................47
7-3. Other problems ........................................... 48
7-4. Built-in calibration sensor and
SelfCalibration problems........................... 49
Chapter 8 Reference ........................................ 50
8-1. Attaching the Optional Arm....................... 50
8-2. Making Use of USB
(Universal Serial Bus)..................................51
●System Requirements ....................................51
●How to connect ..............................................51
8-3. Showing Monitor Information.................... 52
●Displaying signal information .........................52
●Displaying Monitor Information ......................52

6Contents
8-4. Specications ............................................. 53
Chapter 9 Glossary .......................................... 56
Appendix.............................................................. 59
Trademark ............................................................... 59
License / Copyright................................................ 59
FCC Declaration of Conformity ............................ 60
LIMITED WARRANTY..............................................61
Recycling Information ........................................... 62

7
Chapter 1 Introduction
Chapter 1 Introduction
1-1. Features
• 24.1″ widescreen
• Wide color gamut (Adobe® RGB coverage: 99%)
• Achieves contrast ratio of 1500:1*1
A high contrast ratio allows for display of crisper black with reduced whiteness.
*1 Standard value. When “DUE Priority” is set to “Brightness"
• Supports a resolution of 1920 × 1200
• IPS panel with 178˚ wide viewing angle in landscape and portrait mode.
• Frame synchronization mode supported (23.75–30.5 Hz, 47.5–61.0 Hz)
• 3 signal input terminals (DVI-D × 1, HDMI × 1, DisplayPort × 1)
- DisplayPort (supports 8 bit and 10 bit)*1
- HDMI (supports 8 bit, 10 bit, and 12 bit)*1, *2
Can handle PC signals in HDMI input
*1 Audio is not supported.
*2 The maximum screen display is 10 bits.
• Color mode function
Reproduces a color temperature, gamma, and gamut compliant with the following standards.
- Broadcasting standards “EBU/REC709/SMPTE-C”
- Digital cinema standard “DCI”
- Adobe® RGB / sRGB
See “2-2. Selecting the display mode (color mode)” (page 19)
• An Adjustment Certicate, which describes the factory measurement results of the grayscale and
uniformity characteristics is attached for each monitor.
• This product is equipped with a built-in calibration sensor, and supports SelfCalibration in which the
monitor executes calibration independently.
See “Chapter 4 SelfCalibration” (page 34)
• The provided Color Management Software “ColorNavigator 6” enables you to calibrate monitor
characteristics and generate color proles
See “1-3. EIZO LCD Utility Disk” (page 11)
• Monitor hood is included
Includes a monitor hood that can effectively shield the monitor from the reection of external lighting, such as
the reected glare of a uorescent light.
• Displays HDCP (High Bandwidth Digital Protection) protected content.

8Chapter 1 Introduction
Attention
Be careful of the following points when using the built-in calibration sensor.
Do not touch the built-in calibration sensor.
It may reduce the measurement accuracy of the built-in calibration sensor, or result in injury
or equipment damage.
Attention
• A high temperature or high humidity environment may affect the measurement accuracy of the built-in
calibration sensor. We suggest storing and using the monitor under the following conditions.
- Temperature 30 ºC or less
- Humidity 70% or less
Avoid storing or using the sensor where it may be exposed to direct sunlight.
• Since the measurement result for the built-in sensor may be affected, ensure that the level of ambient light
that enters the receiver part of the built-in sensor does not change signicantly during measuring.
- The use of a monitor hood is recommended.
- While measuring, do not bring your face or any objects close to the monitor, do not look into the sensor.
- Set the monitor in the environment so that external light does not enter the sensor directly.

9
Chapter 1 Introduction
1-2. Controls and Functions
●Front
7 8 92 4 53
6
1
Adjustment menu*1
1. Built-in calibration
sensor
Executes calibration for independent monitors. SelfCalibration function
(page 34)
Attention
• Do not touch the sensor as this will affect the measurement accuracy.
2. Ambient Light Sensor Measures ambient light.
3. button Switches input signals for display (page 42).
4. button Changes Color Mode (page 19).
5. button Cancels the setting/adjustment and displays the Adjustment menu.
6. /button • Provides the menu selection as well as the adjustment and setting of a
function.
• Displays the Brightness menu (page 20).
7. button Displays the Adjustment menu, determines adjustment items on the menus, and
saves values adjusted.
8. button Turns the power on or off.
9. Power indicator Indicates the monitor’s operation status.
Blue : Operating
Flashing blue
(2 quick ashes
at a time)
: Indicates that recalibration is required if the SelfCalibration
schedule (page 36) is set.
Orange : Power saving mode
OFF : Main power/Power off
*1 See “1-4. Basic Operations and Functions” (page 12) for instructions on how to use.

10 Chapter 1 Introduction
●Rear
16
17
15
10 11 12 13 14
10. Main power switch Turns the main power on or off.
: On : Off
11. Power connector Connects the power cord.
12. Input signal connectors Left: DVI-D connector
Middle: HDMI connector
Right: DisplayPort connector
13. USB upstream port Connects to the USB cable when using software that requires a USB
connection, or when using the USB Hub function. (page 51)
14. USB downstream port Connects to a peripheral USB device.
15. Stand*2 Used to adjust the height and angle of the monitor screen.
Attention
• Do not hold the sensor section on the front side of the monitor when
adjusting the height or angle.
16. Security lock slot Complies with Kensington’s MicroSaver security system.
17. Cable holder Covers the monitor cables.
*2 An optional arm (or an optional stand) can be attached by removing the stand section (see “1-4. Basic
Operations and Functions” (page 12)).

11
Chapter 1 Introduction
1-3. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The disk contents are shown below:
●Disk contents
The disk includes application software programs for calibration, and the User's Manual. Refer to
“Readme.txt” or the “read me” le on the disk for software startup procedures or le reference
procedures.
Contents Windows Macintosh
• A “Readme.txt” or “read me” le √ √
• ColorNavigator 6
√ √
- An application software for measuring and calibrating monitor characteristics
and generating ICC proles (for Windows) and Apple ColorSync proles (for
Macintosh).
(The monitor and PC must be connected using the USB cable.)
• Screen adjustment pattern les*1
√ -
- Used when adjusting the image for analog signal input manually.
• User’s Manual of this monitor (PDF le) √ √
*1 This monitor does not support analog signal input, so these les are not used.
●To use ColorNavigator 6
Refer to the User’s Manual on the CD-ROM disk for details on how to install and use the software. When
using this software, you will need to connect a PC to the monitor with the supplied USB cable. For
details of the USB cable connection, see “8-2. Making Use of USB (Universal Serial Bus)” (page 51).

12 Chapter 1 Introduction
1-4. Basic Operations and Functions
●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press any button (except ).
A guide indicating the button functions is displayed.
Buttons
Guide
2. Press . The Adjustment menu appears.
Current mode
Menu title
Setting
Menu
Item
2.
Adjusting/setting
1. Using / , select the menu you want to adjust/set and press .
2. Using / , select the item you want to adjust/set and press .

13
Chapter 1 Introduction
3. Using / , adjust/set the selected item and press .
3.
Exiting
1. Press a few times to exit the Adjustment menu.
●Functions
The following table shows the menus for adjustment and setting items of each menu.
Main Menu Item Reference
Color
(Standard Mode)*1
Brightness “2-3. Adjusting the Color” (page 20)
Temperature
Gamma
Color Gamut
Advanced
Settings
Hue
Saturation
Clipping
Gain
Black Level
6 Colors
Color Reset “3-6. Reset to default” (page 33)
Color
(CAL Mode)*2 Target SelfCalibration “4-1. Setting the Color Mode for Executing
SelfCalibration” (page 34)
Brightness “4-4. Setting the calibration targets” (page 38)
White Point
Color Gamut
Gamut Settings
Gamma
Results Calibration
Result
“4-6. Checking Adjustment Results” (page 40)
Ambient Light
Color Reset “3-6. Reset to default” (page 33)

14 Chapter 1 Introduction
SelfCalibration Execute “4-5. Executing SelfCalibration” (page 39)
Standard Mode SelfCalibration “4-1. Setting the Color Mode for Executing
SelfCalibration” (page 34)
Results “4-6. Checking Adjustment Results” (page 40)
Settings Schedule “4-3. Setting Calibration Schedule” (page 36)
Clock
Adjustment
“4-2. Setting Monitor Date and Time” (page 35)
Screen Screen Size “To select screen size” (page 17)
Color Space “2-4. Specifying Color Space” (page 26)
Input Range “2-5. Expanding Signal Output Range” (page 27)
HDMI
Settings*3
Noise Reduction
“2-6. Setting HDMI” (page 28)
Film detection
Safe Area Marker
Safe Area Size
Border Color
Power
Manager
Power Save “6-1. Setting Power Save” (page 44)
Indicator brightness “6-2. Adjusting Brightness of Front Button” (page
45)
Menu Settings Language “Selecting the Language” (page 30)
Orientation “Setting Orientation” (page 30)
Menu Position “To change adjustment menu display position”
(page 31)
Tools Input Selection “5-2. Setting Input Signal Switching Procedure”
(page 42)
Input Skip “5-3. Skipping Unused Input Signals” (page 42)
Mode Skip
“3-2. Skipping Unused Display Modes” (page 31)
USB Selection
“5-4. Switching USB Port Automatically” (page 43)
Signal Info “8-3. Showing Monitor Information” (page 52)
Monitor info
All Reset “3-6. Reset to default” (page 33)
*1 Functions available for adjustment and setting in Standard Mode (page 19) are displayed.
*2 Functions available for adjustment and setting in CAL Mode are displayed.
*3 This function is available with HDMI signal input.

15
Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Setting Resolution
●Compatible Resolutions/Formats
The monitor supports the following resolutions.
When using PC signal input (DVI-D, DisplayPort, HDMI: PC)
Resolution Vertical scan
frequency
640 × 480 60 Hz
720 × 400 70 Hz
800 × 600 60 Hz
1024 × 768 60 Hz
1280 × 960 60 Hz
1280 × 1024 60 Hz
1600 × 1200 60 Hz
1680 × 1050 60 Hz
1920 × 1080 60 Hz
1920 × 1200 *1 60 Hz
*1 Recommended resolution
When using Video signal input
Formats Vertical scan
frequency Resolution Scan Type DVI*3 Display Port*3
HDMI
Video*1,2 PC*3
640 × 480 60 Hz 640 × 480 Progressive √ √ √ √
480i 60 Hz 720 × 480 Interlace - - √ -
480p 60 Hz 720 × 480 Progressive - √ √ -
576i 50 Hz 720 × 576 Interlace - - √ -
576p 50 Hz 720 × 576 Progressive - - √ -
720p 50 Hz / 60 Hz 1280 × 720 Progressive √ √ √ √
1080i 50 Hz / 60 Hz 1920 × 1080 Interlace - - √ -
1080p
24 Hz / 25 Hz /
30 Hz / 50 Hz /
60 Hz
1920 × 1080 Progressive √ √ √ √
*1 YUV data input is supported.
*2 To display video signals by HDMI signal input, you must change the monitor settings beforehand
(see “To switch signal formats (Only for DisplayPort or HDMI signal input)” (page 16)).
*3 The output device must be dened. Refer to the User’s Manual of the output device for further details.

16 Chapter 2 Adjusting Screens
●
To switch signal formats (Only for DisplayPort or HDMI signal input)
The monitor’s displayable resolution can be changed. To display video signals when using HDMI
signal input, set to “Video”.
Setting Range
- DisplayPort: “RGB” / “RGB/YUV"
- HDMI: “Video” / “PC"
Procedure
1. Press to turn off the monitor.
2. Holding down, press for at least two seconds to turn on the monitor.
The “Optional Settings” menu appears.
3. Choose “Signal Selection” from “Optional Settings”, and press .
4. Choose the input signal to set with or , and press .
5. Select “Signal Format” with the selected input signal and press .
6. Switch the signal format with or .
7. Select “Finish” with or .
8. Press .
●To set the display resolution for the OS
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 10
1. Right-click the mouse anywhere on the desktop except on icons.
2. From the displayed menu, click “Display settings”.
3. In the “Customize Display” dialog box, click “Advanced Settings”.
4. Select the monitor, and select the resolution from the “Resolution” pull-down menu.
5. Click “Apply”.
6. When a conrmation dialog box appears, click “Keep changes”.
Windows 8.1 / Windows 7
1. For Windows 8.1, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click anywhere on the desktop except for on icons.
3. From the displayed menu, click “Screen resolution”.
4. Select a monitor, then choose a resolution from the “Resolution” pull-down menu.
5. Click “OK”.
6. When a conrmation dialog box is displayed, click “Keep changes”.
Note
• If you want to change the size of displayed characters and other items, select “Display” from Control Panel
and change the zoom percentage.

17
Chapter 2 Adjusting Screens
OS X Mountain Lion (10.8) or later
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays”. (For OS X Mountain Lion
(10.8), click “Displays” for “Hardware”.)
3. In the displayed dialog box, select the “Display” tab and select “Change” in the “Resolutions” eld.
4. Select the desired resolution from the list of possible resolution settings. If the desired resolution is
not displayed in the list, hold down the Option key and select “Change”.
5. Your selection will be reected immediately.When you are satised with the selected resolution,
close the window.
Mac OS X 10.7
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. In the displayed dialog box, select the “Display” tab and select the resolution in the “Resolutions”
eld.
4. Your selection will be reected immediately.When you are satised with the selected resolution,
close the window.
●To select screen size
The image with the resolution other than the recommended resolution is displayed in full screen
automatically. You can change the screen size by using the “Screen Size” function from “Screen”.
When using PC signal input
Setting Function
Full Displays an image in full screen. Images are distorted in some cases because the vertical
rate is not equal to the horizontal rate.
Enlarged As far as possible, images are enlarged to full screen without changing the aspect ratio.
Blank horizontal or vertical borders may appear to maintain aspect ratio.
Normal Displays images with the specied resolution.
Example: Image size 1280 × 1024
Full Enlarged Normal
1920 × 1200 1500 × 1200 1280 × 1024
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Full”, “Enlarged”, or “Normal” with or .
4. Press after completing the setting.

18 Chapter 2 Adjusting Screens
When using video signal input
●When displaying HD signals (720p, 1080i, 1080p)
Setting Function
Enlarged As far as possible, images are enlarged to full screen without changing the aspect ratio.
Blank borders may appear at the top and bottom of the screen to maintain the aspect
ratio.
Dot by Dot Displays images with the specied resolution.
Example: 720p
Enlarged Dot by Dot
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Enlarged”, or “Dot by Dot” with or .
4. Press after completing the setting.
●When displaying SD signals (640 × 480, 480i, 480p, 576i, 576p)
Setting Function
Auto The monitor automatically changes the screen size according to the aspect ratio sent
from the auto input signal.
4:3 Displays images in a 4:3 format screen. Black bars appear on both sides of the screen.
16:9 images are horizontally compressed.
Letter Box Displays 16:9 letterboxed images in full screen.
Images other than the letterboxed ones are partly cut on top and bottom.
16:9 Displays the entire 16:9 image in full screen. Black bars appear on the top and bottom of
the screen.
4:3 images are horizontally expanded.
Example: 480i/480p (16:9)
Auto 4:3 Letter Box 16:9
Procedure
1. Choose “Screen” from the Adjustment menu, and press .
2. Choose “Screen Size” from “Screen”, and press .
3. Select “Auto”, “4:3”, “Letter Box”, or “16:9” with or .
4. Press after completing the setting.

19
Chapter 2 Adjusting Screens
2-2. Selecting the display mode (color mode)
This function allows easy selection of a desired mode according to monitor application.
●Display Modes
Mode Purpose
Standard Mode Adjust color using the monitor’s Adjustment menu.
1-Custom Available for the color settings according to your preference.
2-Adobe®RGB Suitable for color matching with Adobe®RGB compatible peripherals.
3-sRGB Suitable for color matching with sRGB compatible peripherals.
4-EBU Suitable for reproducing the color gamut and gamma as dened in the EBU
(European Broadcasting Union) standards.
5-REC709 Suitable for reproducing the color gamut and gamma as dened in the
ITU-R Rec. 709 standard.
6-SMPTE-C Suitable for reproducing the color gamut and gamma as dened in the SMPTE-C standard.
7-DCI Suitable for reproducing the color gamut and gamma as dened in the DCI standard.
CAL Mode Adjust the monitor’s color using software.
8-CAL1
9-CAL2
10-CAL3
Displays the screen adjusted by the Color Management Software “ColorNavigator 6” and
SelfCalibration.
Attention
• Avoid adjusting the screen or color while using ColorNavigator 6.
Procedure
1. Press any button (except ).
The guide is displayed.
2. Press .
The mode menu appears at the bottom left of the screen.
1-Custom
↓↑
2-Adobe®RGB
↓↑
3-sRGB
↓↑
4-EBU
↓↑
5-REC709
↓↑
6-SMPTE-C
↓↑
7-DCI
↓↑
8- CAL1
↓↑
9-CAL2
↓↑
10-CAL3
Example
3. The mode among the list is highlighted in turn each time is pressed.
You can switch the mode with or while the mode menu is displayed.

20 Chapter 2 Adjusting Screens
Note
• The Adjustment menu and the Mode menu cannot be displayed at the same time.
• You can disable a specic mode to be selected. For more information, see “3-2. Skipping Unused Display
Modes” (page 31).
• The adjustment result of ColorNavigator 6 is reected in each of the following modes, depending on the
connector used for connecting the monitor and PC.
- CAL1: DVI
- CAL2: DisplayPort
- CAL3: HDMI
2-3. Adjusting the Color
When displaying in Standard Mode, the “Color” menu of the Adjustment menu allows you to set and save
independent color adjustments for each mode.
Attention
• It takes about 3 minutes (under our measurement conditions) for the performance of electrical parts to stabilize.
Please wait 3 minutes or more after the monitor has been turned on before adjusting the monitor.
• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.
Note
• Use the adjustment criteria shown in “cd/m2”, “K” and “%” as a guide.
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Setting Range
40 cd/m2 to 400 cd/m2
Procedure
1. Press any button (except ).
The guide is displayed.
2. Press or .
The Brightness menu appears.
3. Use or for adjustment.
4. Press after completing the setting.
Attention
• If the entered value cannot be set, the value will appear in magenta. In such a case, change the value.
Note
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.