Elastix ELX5000 User manual




Elastix Appliance
Assembly Process Guide
ELX-5000
PaloSanto Solutions
January, 2012




I. INDIVIDUAL PARTS
Hardware
Brand
Model
Type
Notes:
Mainboard
Intel
S5500BCR
N/A
Hardware included:
- SATA drive data cable
Processor
Intel
Intel Xeon
E5502
Up to 2 Processors
Memory
Kingston / Corsair
240 Pin
DDR3 1333
4 GB
2x 2GB (Up to 32 GB)
Hard Drive
Seagate / Samsung
/ Toshiba
Laptop Size SATA
drive
500 GB
2 discs for Hardware RAID 1
Power Cord
Cable
N/A
110V or 220 V
N/A
Model depends on region it is
shipped to
2U customized
case
EMKO
EM-165B
N/A
No Power Supply Unit preinstalled
Plate for hard disks mounting in
vertical location
LCD
Crystalfontz
CFA635-TFE-KU1
LCD
USB LCD 20x4 +Keypad, White Edge
LED Backlight
LCD USB Cable
Crystalfontz
WRUSBY11
Cable
USB Cable for LCD Panel
Redundant
Power Supply
Unit (PSU)
Zippy
R2W-6500P
N/A
N/A
Case Fan
Cooling
Dynatron
DF128015PH
80mm Fan
Hardware included:
80mm Fan Grill
Screws




II. ASSEMBLY
1. Unscrew the mounting plate on the left side of the Zippy power supply unit. Keep the screws for later use
2. Place de PSU inside the case
3. Fix the PSU to the right side plate using the screws removed in step 1 and to the extra plate so it gets fixed to
the base of the case using the additional screws available
4. Match the faceplate on the back of the case to each port on the back of the motherboard
5. Remove the protective plastic sticker off the LCD screen
6. Screw the LCD screen to the case
7. Screw the motherboard to the bottom of the case
8. Insert the memory module in the motherboard’s memory slot
9. Connect the 24-pin ATX power connector coming from the PSU to the motherboard’s power connector (2 x 12)
10. Screw the fan to the left side of the case and connect its power cord to the PSU
11. Connect the POWER SWITCH cable (orange-white) to the motherboard
12. Connect the HDD LED and Power cables (green-white and red-white , respectively) to the motherboard
13. Screw the SATA disk to the bottom of the case
14. Connect the data cable of the SATA disk to the motherboard
15. Connect the power cable of the SATA disk to the PSU
16. Connect the provided USB cable (WRUSBY11) from the LCD panel (CFA635-TFE-KU1) to an internal USB port of
the motherboard
17. Secure cables conveniently using nylon cable ties
NOTE: the assembly process will be completed in the VII. PACKAGING section of this document, once the installation of
Elastix has been finished and tested
III. PRE-INSTALLATION
1. Connect the data and power cables of a SATA CD or DVD drive to the motherboard (skip this step if installing
Elastix from an external optical drive instead)
2. If instead an external optical drive is used for the installation (not recommended), connect it to the
corresponding port on the back of the ELX-5000
3. Connect the Power Cord Cable to the PSU connector on the back of the ELX-5000 and then to a nearby outlet
4. Press the power button to turn on the appliance
Green
(empty)
White
Red
White
White
Orange




5. Place in the optical drive a CD or DVD containing the latest Elastix stable 64 bits version found in
http://sourceforge.net/projects/elastix/files/Elastix%20PBX%20Appliance%20Software/
(this guide was written using Elastix 2.2)
6. Reboot the appliance if necessary until the following screen is displayed:
IV. ELASTIX INSTALLATION
1. Press ENTER to begin the installation
2. Select English as the language for the installation:




3. Select 'us' as the type of keyboard:
4. Choose “Create custom layout.”:




5. Hard Disk Drive distribution:
Partition Type Size
RAID (swap) 4096 MB
/boot RAID (ext3) 200 MB
/ RAID (ext3) 450 GB
software RAID 4096 MB
software RAID 200 MB
software RAID 450 GB
Leave the remaining space free for posible High Availability implementations in the future
6. Select to configure the Network Interface:




7. Select to activate on boot and to enable IPv4 support:
8. Manually assign the IP address 192.168.1.251 / 24:




9. Enter 192.168.1.1 as the Gateway and Primary DNS addresses:
10. Type 'elx.palosanto.com'as the hostname:




11. Select the time zone according to the city where the appliance is going to be used in:
12. Type 'palosanto'as the password for root:




13. Wait until the package installation finishes:
14. After the automatic reboot, type 'palosanto'as the password for the MySQL root user:




15. Reenter the MySQL root user password just typed:
16. Type 'palosanto'as the password for the admin user:




17. Reenter the password for the admin user just typed:
V. POST INSTALLATION TESTS
1. Confirm the installation was completed successfully:
a. Log into the console (Login: root - Password: palosanto)
b. Execute the following line:
md5sum /root/install.log
c. The following output should be displayed (for Elastix 2.2 64 bits):
6fdb48a138023e6fd0aa2700b3adc6e3
2. Confirm correct access to Elastix’s web UI is possible:
a. Connect the Ethernet port on the ELX-5000 to a free Ethernet port on a computer nearby (using a
normal Ethernet straight-thru patch cord)
b. Configure that NIC on the computer with IP address 192.168.1.1 (mask 255.255.255.0)
c. From a web browser on the computer go to the URL: https://192.168.1.251
d. Username: admin
e. Password: palosanto
f. Elastix’s Dashboard should be displayed
3. Confirm correct access to Elastix’s shell via ssh is possible:
a. Open a terminal software on the computer used on the previous test and execute:
ssh [email protected]
b. As the password type: palosanto
c. Access into Elastix’s shell should have been granted
4. Confirm correct access to MySQL is possible:
a. Using the same ssh session opened in the previous test execute the following line:
mysql -uroot –ppalosanto
b. Access into the MySQL monitor should have been granted




VI. LCD SCREEN CONFIGURATION
1. Execute the following command in Elastix’s linux shell:
crystalfontz.pl
2. This will open a cli session with the LCD controller where the following commands need to be executed:
_lcd_> clear
_lcd_> pos_data 2 2 Booting Elastix…
_lcd_> store_state
_lcd_> quit
3. Back in Elastix’s linux shell, execute the following commands:
chown asterisk:asterisk –R /opt/lcdelastix
service LCDd start
service lcdelastix start
chkconfig LCDd on
chkconfig lcdelastix on
4. Navigate through the LCD screen menus to confirm the configuration was successful
VII. PACKAGING
1. Before turning off the ELX-5000 to begin packing it, run the following console command:
history -c
2. Press the ELX-5000’s Power button and wait for the shutdown process to complete
3. Disconnect and tidily tie the power cord
4. Disconnect the data and power cables of the SATA CD or DVD drive from the motherboard (skip this step if you
installed Elastix from an external optical drive instead)
5. If instead an external optical drive was used for the installation (not recommended), disconnect it from the
corresponding port on the back of the ELX-5000
6. Place the warranty seals on the telephony cards inside the appliance (if applicable)
7. Place and screw both covers to the top of the case
8. Place the warranty seals on all three outside edges on the case’s top cover (the cover with the Elastix logo)
9. Generate and place the label with the Serial Number on the right side of the case (when the power button is
facing you)
10. Wrap the ELX-5000 inside the plastic bag
11. Place the two pieces of sponge on the case’s lateral ends
12. Place the appliance, with the sponges on its sides, inside the box
13. Ensure that the following parts and documents are properly placed inside the ELX-5000’s box:
Power cord (either American or European model depending on the region it will operate in)
Two rack-mounting ears and 6 screws for attaching them to the case
Two “L” shaped metallic supports for rack mounting
“Please Read First” sheet
Service Letter
Invoice / Delivery Note
Original telephony PCI card’s box (if applicable)
14. Close the box and secure it with packing tape