Cisco MX200 G2 User manual

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 1
This installation guide covers MX200 G2 with a wheel base.
Dimensions
Height: 1480mm / 58.3in.
Width: 995 mm / 39.2 in.
Depth: 715 mm / 28.0in.
Weight total: 33 kg / 73 lb
Weight monitor: 24 kg / 53lb
Manpower
Two people working together are required to mount the
monitor to the base module.
Room setup
Explore the Cisco Project Workplace website to
find inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
Documentation
Cisco Spark: Visit the Cisco Spark help site to find
more information about Spark registered room
systems, http://help.ciscospark.com
Other services: Visit the Cisco web site to find user
guides and compliance and safety information for
the video system, http://www.cisco.com/go/mx-docs

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 2
C
D
A
B
E
• Wheel base
• Column
• Screws for
the base
• Screwdriver
Accessories:
• Microphone(s)
• Cables
• Screws for mounting the monitor
• Gloves
Monitor
Back cover
Touch controller

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 3
Optional
It is possible to replace the wheels with rubber pads.
The rubber pads are kept underneath the wheel
base, and must be moved to their correct position.
M5x8 (Allen key, 3 mm)
1Mount the wheel base
A
You may place the column on the empty
wheel base box as illustrated. Then it is
easier to enter the screws from below.
4 ×
1
4 × M6x20
2
3

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 4
2Mount the monitor
The monitor may be tilting slightly
forward. If you gently pull it to a vertical
position, the screws enter more easily.
Front
B C
Use gloves when
handling the monitor.
Remove the cable
channel lid for now.
You need it in step 4.
4 × M6x16

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 5
3Connect the cables
Thread the cables up
through the hole in the base.
C D
For maintenance only
Reset to factory
settings
Audio line output
Always use the provided
power cable.
The wall socket outlet must
be easily accessible after
installation.
Power switch Audio line input
LAN1
Video input2
(e.g. PC)
Video output2
(e.g. 2nd display)
Power (100-240 VAC, 50/60 Hz)
Touch
controller1
USB, for future use
HDMI
DVI-I
Microphone3
2nd microphone2, 3
1Use the cable that is labeled
with for the Touch controller;
use the cable that is labeled
with for the LAN
2Optional
3Always use the provided
Cisco TelePresence Table
Microphone 20

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 6
• Connect to power and LAN/Ethernet.
• Switch on the system. The power switch is
placed next to the power connector at the
rear side of the system.
Wait while the unit starts up. Normally this takes a few
minutes. It may include automatic software upgrade and
restart of the Touch controller.
• Follow the instructions on the Touch controller.
Cisco Spark: To find more information on how to
get started with Spark registered systems, visit
http://help.ciscospark.com and look for Getting Started
articles for room systems.
Other services: For further information on set-up and
configuration, download the Getting Started Guide from the
Cisco web site, http://www.cisco.com/go/mx-docs
Never move the camera manually when power is switched
on; always use the camera control function on the Touch
controller to change the camera position.
5Start up the system
Snap on the cable
channel lid for strain relief.
Lead the cables out at the
front or back as appropriate.
4Snap on the cable channel lid

Installing Cisco TelePresence MX200 G2 - Wheel Base
78-100248-02A0 | JUNE 2016 | © 2016 Cisco Systems, Inc. All rights reserved. 7
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
声明
此为
A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.
6Mount the back cover
E
Wind up the cables on the hook on the
back cover when rolling the unit. Also
hang the Touch controller on the hook.
Lift this handle to
lock/unlock the back
cover. Use both
hands if required.
Cisco has more than 200 offices worldwide.
Find an overview of the offices on the Cisco web site at
http://www.cisco.com/go/offices
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or
its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to
this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the
property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1110R)