Elation ELAR EXTQW BAR HP User manual

ELAR EXTQW BAR HP™
user manual 1.0! !
ELATION
|
ELAR EXTQW BAR HP
!™
|user manual 1.0

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!2!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
©2013 ELATION PROFESSIONAL all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without notice.
ELATION PROFESSIONAL logo and identifying product names and numbers herein
are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.
!
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a result of the improper,
unsafe, insufficient and negligent assembly, installation, rigging, and operation of
this product.
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, Netherlands
[phone] | [phone]
fax
|
www.elationlighting.eu | [e-mail]
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 |323-832-9142 fax | www.elationlighting.com | [e-mail]

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!3!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
CONTENTS
General Information
4
Warranty
6
Safety Instructions
7
General Guidelines
8
Fixture Control
9
DMX Channel Modes And Functions
11
Cleaning and Maintenance
14
Technical Specifications
15
Optional Accessories
17

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!4!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
GENERAL INFORMATION
INTRODUCTION
Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The ELAR EXTQW BAR HP™has been
designed to perform reliably for years when the guidelines in this booklet are
followed. Please read and understand the instructions in this manual carefully
and thoroughly before attempting to operate this unit. These instructions contain
important information regarding safety during use and maintenance.
IP65 RATED
An IP rated lighting fixture is one, which is commonly installed in outdoor
environments and has been designed with an enclosure that effectively protects
the ingress (entry) of external foreign objects such as dust and water. The
International Protection (IP) rating system is commonly expressed as "IP" (Ingress
Protection) followed by two numbers (i.e. IP65) where the numbers define the
degree of protection. The first digit (Foreign Bodies Protection) indicates the
extent of protection against particles entering the fixture and the second digit
(Water Protection) indicates the extent of protection against water entering the
fixture. An IP65 rated lighting fixture such as the LEVEL Q7 IP™ is one which has
been designed and tested to protect against the ingress of dust (6) and high
pressure water jets from any direction (5).
UNPACKING
Thank you for purchasing the ELAR EXTQW BAR HP™by Elation Professional®. Every
ELAR EXTQW BAR HP™has been thoroughly tested and has been shipped in
perfect operating condition. Carefully check the shipping carton for damage
that may have occurred during shipping. If the carton appears to be damaged,
carefully inspect your unit for damage and be sure all accessories necessary to
operate the unit have arrived intact. In the event damage has been found or
parts are missing, please contact our customer support team for further
instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below. Please do not discard the shipping
carton in the trash. Please recycle whenever possible.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!5!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
BOX CONTENTS
•(1) 7.9 ft. (201mm) 4pin Female to Edison Power Cable
•(1) 6.6 ft. 3pin Male XLR to 3pin Female DMX Cable
•(1) 6.6 ft. 3pin Female XLR to 3pin Male DMX Cable
•(1) Bag of DMX End Caps
•Manual & Warranty Card
MANUAL UPDATES
Please check www.elationlighting.com for the latest updated version of this manual.
CUSTOMER SUPPORT
Elation Professional®provides a customer support line, to provide set up help and
to answer any question should you encounter problems during your set up or
initial operation. You may also visit us on the web at www.elationlighting.com for
any comments or suggestions. For service related issue please contact Elation
Professional®. Service Hours are Monday through Friday 8:00 am to 5:00 pm PST.
Voice: 323-582-3322 Fax: [phone]
E-mail: [email protected] Forum: www.ElationLighting.com/forum
WARRANTY REGISTRATION
The ELAR EXTQW BAR HP™carries a two year (730 days) limited warranty. Please fill
out the enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and accompany
a return authorization (R.A.) number. The R.A. number must be clearly written on
the outside of the return package. A brief description of the problem as well as
the R.A. number must also be written down on a piece of paper and included in
the shipping container. If the unit is under warranty, you must provide a copy of
your proof of purchase invoice. Items returned without a R.A. number clearly
marked on the outside of the package will be refused and returned at
customer’s expense. You may obtain a R.A. number by contacting customer
support at 323-582-3322.
IMPORTANT NOTICE!
There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself; doing so will void your manufactures warranty. Damages resulting from
modifications to this fixture and/or the disregard of safety and general user
instructions found in this user manual void the manufactures warranty and are
not subject to any warranty claims and/or repairs.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!6!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
2 - YEAR LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free
of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of
purchase. This warranty shall be valid only if the product is purchased within the United States of America,
including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase
by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All shipping charges must
be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this
warranty, Elation Professional® will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be
shipped with the product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which Elation Professional® concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the Elation Professional® factory unless prior
written authorization was issued to purchaser by Elation Professional®; if the product is damaged because not
properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic
check-up. During the period specified above, Elation Professional® will replace defective parts at its expense,
and will absorb all expenses for warranty service and repair labor by reason of defects in material or
workmanship. The sole responsibility of Elation Professional® under this warranty shall be limited to the
repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional®. All
products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
effect.
E. Elation Professional® reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made by
Elation Professional® in connection with this product, including warranties of merchantability or fitness, are
limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied,
including warranties of merchantability or fitness, shall apply to this product after said period has expired. The
consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above;
and under no circumstances shall Elation Professional® be liable for any loss or damage, direct or
consequential, arising out of the use of, or inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® Products and supersedes all
prior warranties and written descriptions of warranty terms and conditions heretofore published.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!7!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
SAFETY INSTRUCTIONS
The ELAR EXTQW BAR HP™is an extremely sophisticated piece of electronic
equipment. To guarantee a smooth operation, it is important to follow the
guidelines in this manual. The manufacturer of this device will not accept
responsibility for damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
•For proper operation, follow the Installation guidelines described in this manual. Only qualified
and certified personnel should perform the installation and only the original rigging parts
(brackets, holders, clamps, safety cables) included with this fixture should be used for installation.
Any modifications will void the original manufactures warranty and increase the risk of damage
and/or personal injury.
•Never look directly into the light source to prevent risk of injury to your retina, which may induce
blindness. Those suffering from EPILEPSY should avoid looking directly into the light source of this
unit at all times.
•The fan and air inlets must remain clean and never blocked. Allow approx. 6” (15cm) between
this fixture and other devices or a wall for proper cooling.
•Always disconnect from main power source before performing any type of service and/or
cleaning procedure. Only handle the power cord by the plug end, never pull by tugging the wire
portion of the cord.
•Do NOT operate fixture if the power cord has become frayed, crimped and/or damaged. If the
power cord is damaged, replace it immediately with a new one of similar power rating.
•Do NOT operate fixture near any flammable materials.
This device falls under PROTECTION CLASS 1. It’s essential this device is
grounded properly, and only qualified personnel perform all electrical
connections.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!8!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
GENERAL GUIDELINES
•NEVER OPEN THIS FIXTURE WHILE IN USE!
•During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp and will
decrease gradually over time.
•Please make sure there are NO FLAMMABLE MATERIALS close to the fixture while
operating, to prevent any fire hazard.
•The fixture must be installed in a location with adequate ventilation, at least 1.5
feet (2.5m) from adjacent surfaces. Be sure no air ventilation slots are blocked.
•DO NOT attempt installation and/or operation without knowledge how to do so.
•DO NOT permit operation by persons who are not qualified to operate this type of
fixture. Most damages are the result of operations by nonprofessionals.
•Consistent operational breaks may ensure the fixture will function properly for
many years to come.
•DO NOT shake fixture, avoid brute force when installing and/or operating fixture.
•Always install the fixture with an appropriate safety cable. When installing the
fixture in a suspended environment, always use mounting hardware that is no less
than M10 x 25 mm, also be sure the hardware is insert in the pre-arranged screw
holes in the bracket of the fixture.
•Use the original packaging and materials to transport the fixture in for service.
•DO NOT TOUCH the housing bare-hand during its operation. Turn OFF the power
and allow approximately 15 minutes for the fixture to cool down before replacing
or serving.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!9!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
FIXTURE CONTROL
The ELAR WR II IR Remote (pictured below) is required to make menu changes to this fixture.
(Optional accessory SKU# ELAR WR II)
NOTE:
The Remote must be aimed towards the front of the fixture and within a distance of 32 ft. (10m).
Select Program Mode
Press PROG button to cycle among static color select mode, color-jumping mode, COLOR FADE
mode and auto run mode. Each press of this button will change to the next mode.
1. When the red color glow and then automatically off indicates that the LED par goes into the
static color select mode. You can press “+” and “-” or put in two numbers 00-15 to choose the 16
static colors in this mode. You can also press FLASH to turn on/off flash and press “+”and “-” or
put in two numbers 00-15 to adjust the flash speed, 00 is flash off, 01 is the slowest speed, 15 is the
fastest speed.
2. When the green color glow and then automatically off indicates that the LED par goes into
auto run mode. You can also press SPEED to enter speed set mode and press “+”and “-” or put in
two numbers 01-16 to adjust the auto run speed, 01 is the slowest speed, 16 is the fastest speed.
3. When the blue color glow and then automatically off indicates that the LED par goes into
COLOR FADE mode. You can press “+” and “-” or put in two numbers 01-16 to choose the 16
COLOR FADE mode. You can also press SPEED to enter speed set mode and press “+”and “-” or
put in two numbers 01-16 to adjust the COLOR FADE speed, 01 is the slowest speed, 16 is the
fastest speed.
4. When the white color glow and then automatically off indicates that the LED par goes into
color change mode. You can press “+” and “-” or put in two numbers 01-16 to choose the 16
color change mode. You can also press SPEED to enter speed set mode and press “+”and “-” or
put in two numbers 01-16 to adjust the color change speed, 01 is the slowest speed, 16 is the
fastest speed.
M/S mode
Press SL/SA button to select slave mode. The unit will be controlled by the master unit now.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!10!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
Select light program mode
Press R/G/B/W to choose R/G/B/W colors and pressing “+” and “-” or put in three number
000-255 to adjust the intensity of the light. You can also press FLASH to turn on flash and press
“+”and “-” or put in two numbers 00-15 to adjust the flash speed, 00 is flash off, 01 is the slowest
speed, 15 is the fastest speed.
DMX MODE
There are 3 DMX modes; 7 Channel Mode, 11 Chanel Mode, and 51 Channel Mode. You must
set the DMX Channel mode before you address the fixture. To select your desired DMX Channel
mode press the DMX mode button, and then press the “+” or “-” buttons to scroll through the
DMX Channel modes. Once you find your desired DMX Channel mode, set your desired DMX
address:
• If the RED LED’s glow you are in DMX Mode 1: 7 DMX Channels
• If the GREEN LED’s glow you are in DMX Mode 2: 11 DMX Channels
• If the BLUE LED’s glow you are in DMX Mode 3: 51 DMX Channels
Set ADDR
Press this button to set the DMX address or initialize the program, then the red, green, blue and
white lights will flash 2~3 times. Please put in 3 number, for example, 1 2 3. After the red light is on,
please put in the first number. After the first number is accessed the green light will be on, then
put in the second number. When the blue light will be on, please put in the third number. After all
the three number are put in, the red, green, blue and white lights will flash 2~3 times, which
indicate that the DMX address is right and it go in to the DMX MODE automatically. If the address
is wrong the red light will be on. New DMX address should be put in.
If the 951 are put in, red and green lights will be on. Press “0” to initialize the program. If the
wrong address is put in, the red light will be on, indicating new address should be put in. Then the
system will run in the first color-jumping mode.
Black Out mode
Press “BLACK OUT” to set the LED lights power on or power off by pressing this button.
Now you may connect the fixture via XLR connections to the Outdoor LED rectangle light 4in1,
please read the corresponding fixture in this manual to find out about the DMX modes, values
and straits.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!11!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
DMX CHANNEL MODES AND FUNCTIONS
DMX MODE 1: 7 CHANNEL MODE
CH1
CH2
CH3
CH4
CH5
CH6
CH7
MODE
DMX
VALUE
FUNCTION
1
0-20
No Function
Dimming
Dim
Bright
Flash
1-255
Slowest
To
Fastest
Red
(Pixels
1-12)
Green
(Pixels
1-12)
Blue
(Pixels
1-12)
White
(Pixels
1-12)
2
21-41
15 Color
Slow Dream
Speed
0-255
Slow
To
Quick
No
Function
No
Function
No
Function
3
42-62
15 Color
Fade Change
4
63-83
15 Color Chase
5
84-104
15 Color Signal
Direction Flow
6
105-125
15 Color Double
Direction Flow
7
126-146
15 Color Signal
Direction Flow +
Dream 1
8
147-167
15 Color Signal
Direction Flow +
Dream 2
9
168-188
Signal Direction
Section Flow 1
10
189-209
Signal Direction
Section Flow 2
11
210-230
Double Direction
Section Flow
12
231-251
15 Color Mixing
13
252-255
Auto-Run

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!12!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
DMX MODE 2: 11 CHANNEL MODE
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
MODE
DMX
VALUE
FUNCTION
1
0-20
No Function
Dimming
0-255
Dim
Bright
Flash
1-255
Slowest
To
Fastest
Red
(Pixels
1-6)
Green
(Pixels
1-6)
Blue
(Pixels
1-6)
White
(Pixels
1-6)
Red
(Pixels
7-12)
Green
(Pixels
7-12)
Blue
(Pixels
7-12)
White
(Pixels
7-12)
2
21-41
15 Color Slow
Dream
Speed
0-255
Slow
To
Quick
No
Function
No
Function
No
Function
No
Function
No
Function
No
Function
No
Function
3
42-62
15 Color Fade
Change
4
63-83
15 Color
Chase
5
84-104
15 Color
Signal
Direction Flow
6
105-125
15 Color
Double
Direction Flow
7
126-146
15 Color
Signal
Direction Flow
+ Dream 1
8
147-167
15 Color
Signal
Direction Flow
+ Dream 2
9
168-188
Signal
Direction
Section Flow 1
10
189-209
Signal
Direction
Section Flow 2
11
210-230
Double
Direction
Section Flow
12
231-251
15 Color
Mixing
13
252-255
Auto-Run

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!13!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
DMX MODE 3: 51 CHANNEL MODE
CH1
CH2
CH3
CH4
CH5
CH6
CH7
.....
CH48
CH49
CH50
CH51
MODE
DMX
VALUE
FUNCTION
1
0-20
No Function
Dimming
0-255
Dim
To
Bright
Flash
1-255
Slow
To
Fast
Red
(Pixel
1)
Green
(Pixel
1)
Blue
(Pixel
1)
White
(Pixel
1)
.....
Red
(Pixel
12)
Green
(Pixel
12)
Blue
(Pixel
12)
White
(Pixel
12)
2
21-41
15 Color
Slow Dream
Speed
0-255
Slow
To
Fast
N/A
N/A
N/A
N/A
N/A
N/A
N/A
3
42-62
15 Color
Fade Change
4
63-83
15 Color
Chase
5
84-104
15 Color
Single
Direction
Flow
6
105-125
15 Color
Double
Direction
Flow
7
126-146
15 Color
Signal
Direction
Flow + Dream
1
8
147-167
15 Color
Signal
Direction
Flow+ Dream
2
9
168-188
Signal
Direction
Section Flow
1
10
189-209
Signal
Direction
Section Flow
2
11
210-230
Double
Direction
Section Flow
12
231-251
Fifteen Color
Mixing
13
252-255
Auto-Run

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!14!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
CLEANING AND MAINTENANCE
CLEANING
Frequent cleaning is recommended to insure proper function, optimized light output,
and an extended life. The frequency of cleaning depends on the environment in
which the fixture operates: damp, smoky or particularly dirty environments can
cause greater accumulation of dirt on the fixture’s optics.
•Clean the external lens surface at least every 20 days with a soft cloth to avoid
dirt/debris accumulation.
•Never use alcohol, solvents, or ammonia based cleaners.
MAINTENANCE
Regular inspections are recommended to insure proper function and extended life.
There are no user serviceable parts inside this fixture, please refer all other service
issues to an authorized Elation service technician. Should you need any spare parts,
please order genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:
•A detailed electric check by an approved electrical engineer every three
months, to make sure the circuit contacts are in good condition and prevent
overheating.
•Be sure all screws and fasteners are securely tightened at all times. Lose screws
may fall out during normal operation resulting in damage or injury as larger parts
could fall.
•Check for any deformations on the housing, color lenses, rigging hardware and
rigging points (ceiling, suspension, trussing). Deformations in the housing could
allow for dust to enter into the fixture. Damaged rigging points or unsecured
rigging could cause the fixture to fall and seriously injure a person(s).
•Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!15!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
TECHNICAL SPECIFICATIONS
FEATURES
25° Beam Angle
IP65 Rated
Die-Cast Aluminum Housing / Tempered Glass
IR Remote Programmable
Flicker Free Operation for TV and FILM
SOURCE
12 x 5W QUAD Color (RGBW) LEDs
50,000 Hour Average Life
PHOTOMETRIC DATA
1430 LUX (133 FC) @9.8 ft. (3m) 25° Full ON
EFFECTS
Color + Variable Strobe Macros
Electronic Dimming: 0% - 100%
COLOR
RGBW (Red, Green, Blue, White)
CONTROL / CONNECTIONS
3 DMX Channel Modes (7/11/51)
3pin DMX In/Out
4pin Power In/Out
Power Link Multiple Units - (7) at 120V (14) at 240V
SIZE / WEIGHT
Length: 39.4” (1000mm)
Width: 3.5” (90mm)
Vertical Height: 7.1” (181mm)
Weight: 11.5 lbs. (5.2kg)
ELECTRICAL
AC 100-240V - 50/60Hz
90W Max Power Consumption
APPROVALS / RATINGS
CE Pending
cETLus Pending
IP65 Rated
INSTALLATION
Rigging: Integrated Adjustable Mounting Brackets (x2)
Working Position: Any (360°)
INCLUDED ITEMS
(1) 6.5 ft. (2m) 4pin Female to Edison Power Cable
(1) 5.5 ft. (1.7m) 3pin Male to 3pin Female DMX Cable
(1) 5.5 ft. (1.7m) 3pin Female to 3pin Male DMX Cable
(1) Bag of DMX End Caps
(2) Mounting Brackets
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!16!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
PHOTOMETRIC DATA
DIMENSIONAL DRAWINGS

www.elationlighting.com!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!17!!!!!!!!!!!ELAR!EXTQW!BAR!HP™!User!Manual!1.0
OPTIONAL ACCESSORIES
ORDER CODE ITEM
TRIGGER CLAMP Heavy Duty Wrap Around Hook Style Clamp
ELA958/3MPEC 3m (4pin) Power Ext/Link Cable
ELAR 3C-1M 1m (3pin) Signal Ext Cable
ELAR 3C-5M 5m (3pin) Signal Ext Cable
ELAR WR II Infrared Wireless Remote Controller Required To Program Fixture
*Not Included Purchased Separately