Elcometer 319 S User manual

User Guide
Elcometer 319 Model S & T
Dewpoint Meter
www.elcometer.com
R

1
Gauge Overview
2
Box Contents
3
Using the Gauge
4
Getting Started
5
The Sensors
6
Setting Limits
7
Taking a Reading
8
Using External Temperature Probes
9
Statistics
10
Batching - Model T
11
Reviewing Batch Data - Model T
12
Menu Structure - Model S
13
Menu Structure - Model T
14
Downloading Data - Model T
15
Spares & Accessories
16
Warranty Statement
17
Technical Specification
18
Legal Notices & Regulatory Information
www.elcometer.com
For the avoidance of doubt, please refer to the original English language version.
Gauge Dimensions: 174 x 75 x 35mm (6.85 x 2.95 x 1.38")
Gauge Weight: 300g (10.5oz) - including batteries
© Elcometer Limited 2015 - 2016. All rights reserved. No part of this document may be reproduced, transmitted,
transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any
means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of
Elcometer Limited.
Hg
CONTENTS
Pb
R
en-1

1 GAUGE OVERVIEW
1 Surface Temperature Probe
2 Air Temperature & Humidity Probe
3 LED Indicators - Red (left), Green (right)
4 LCD Display
5 Softkeys
6 On/Off Key
7 Wrist Strap Connection
8 USB Data Output Socket (below cover)
9 Battery Compartment
10 Integrated Magnets
11 K-Type Probe Connector (below cover)
www.elcometer.com en-2
2 BOX CONTENTS

Elcometer 319 Dewpoint Meter

Protective Pouch with Belt Clip

2 x AA Batteries

Wrist Harness

®
ElcoMaster Software & USB Cable (Model T only)

Calibration Certificate

User Guide
R
3
1
2
4
5
6
87
9
11
10

3 USING THE GAUGE
www.elcometer.com
en-3
a
R
e
g
f
h
h
i
d
b
c
j
k
l
m
n
o
p
q
r
a
Measurement Units -°C, g/kg,°F, gr/lb
b
Power: USB
c
Bluetooth On
d
Menu Softkey
e
Stats Softkey
f
Batch Softkey (Model T)
g
Hold Current Reading; Start / Stop Logging (Model T)
h
Trend Indicators - Value increasing or decreasing
i
Climatic Parameters - Maximum of 5
j
Power: Batteries - including battery life indicator
k
Manual Logging
l
Batch Softkey - when in batching (Model T)
m
Batch Number / Batch Reading Number (Model T)
n
Alarm - reading outside set and enabled limits
o
Softkeys Locked (Model T)
p
Interval Logging - when in batching (Model T)
q
Thermometer Mode On
r
External Probe Temperature

4.1 FITTING THE BATTERIES
Each gauge is supplied with 2 x AA alkaline
batteries.
To insert or replace the batteries:
1 Remove the battery cover by rotating the
retaining screw anti-clockwise.
2 Insert 2 batteries taking care to ensure
correct polarity.
3 Refit the cover and rotate the retaining screw clockwise to
secure.
The battery condition is indicated by a symbol in the top right of the
displa e more segments displayed, the better the y ( ). Th
condition of the batteries.
When no segments are displayed, it is not advisable to use the
gauge for interval logging over long periods of time (Model T only;
see Section 4.6 - ‘Setting Manual or Interval Logging’ on page en-7).
If the batteries are replaced during interval logging, the gauge may
show ‘Please Wait’ whilst it re-calculates the batch statistics.
When the batteries are nearly depleted, the battery power supply
symbol will start flashing and the gauge emits short beeps every 10
seconds to indicate that the batteries should be changed.
The gauge can also be powered via USB using the USB cable
supplied (Model T) or available to purchase as an accessory
(Model S) - see Section 15 - ‘Spares & Accessories’ on page en-21.
Note: The USB cable can not be used to charge the batteries.
4.2 SELECTING YOUR LANGUAGE
1 Press and hold the ON/OFF button until the Elcometer logo is
displayed.
2 Press Menu/Setup/Languages and select your language using

the softkeys.

3 Follow the on screen menus.
www.elcometer.com en-4
4 GETTING STARTED
R
+-
-+

To access the language menu when in a foreign language:
1 Switch the gauge OFF.
2 Press and hold the left softkey and switch the gauge ON.

3 Select your language using the softkeys.

4.3 SCREEN SETTINGS
A number of screen settings can be defined by the user via
Menu/Setup/Setup Backlight including:
 Backlight Brightness; This can be set to ‘Low’, ‘Medium’ or
‘High’.
 Backlight Timeout; The display will dim if inactive for the
period defined by the user. To adjust the backlight timeout use

the softkeys to highlight ‘Backlight Timeout’ and press

‘Sel’. Use the softkeys to set the required value - between

0 (off) and 60 seconds - and press ‘Ok’ to set or ‘Esc’ to
cancel.
The gauge can also be set to switch off automatically after a user
defined period of inactivity - between 1 and 10 minutes - via
Menu/Setup/Auto Switch Off.
Note: ‘Auto Switch Off’ is disabled when the gauge is powered by the USB
connection.
4.4 SETTING UP THE READING DISPLAY
The user can select up to five climatic parameters to be displayed
on screen. Measurements are taken for all climatic parameters but
only those selected are displayed. Users can select from:
 RH; % Relative Humidity
 Ts; Surface Temperature
 Ta; Air Temperature
 Td; Dewpoint Temperature - calculated from Ta and RH
 TΔ; Delta Temperature - the difference between surface
temperature and dewpoint
 Tdb; Dry Bulb Temperature - equal to Ta
4 GETTING STARTED (continued)
www.elcometer.com
en-5
R

 Twb; Wet Bulb Temperature - calculated from Ta and RH
 SH; Specific Humidity - calculated from Ta and RH
Note: The formula used for calculation of Twb and SH uses a fixed value of air
pressure set at 1.0 atmosphere (1013mbar). The accuracy of Twb and
SH will vary at other values of atmospheric pressure. This variation may
be greater than ±1°C for Twb and ±1% / 10 mbar for SH.
To setup the display:
1 Press Menu/Setup/Display/Select
Readings.
2 Use the softkeys to highlight the

required option and press ‘Sel’.
Pressing ‘Sel’ again will de-select the
option.
 The gauge will beep if the user attempts to
select a parameter when five are already
selected in which case, a parameter must
be de-selected before another is chosen.
3 To select which parameter is shown in
the largest digits at the bottom of the
display, press
Menu/Setup/Display/Main Reading.
4 Use the softkeys to highlight the

required option from the list displayed
and press ‘Sel’.
 Only those climatic parameters selected via Step 2 above will be available
for selection in the ‘Main Reading’ list.
 To increase the size of the main reading, reduce the number of
parameters displayed on the reading screen.
Note: If a reading exceeds any set limits during measurement, it will be shown
flashing on the display, even if it has not been selected for display via
Steps 1-2 above.
4.5 SELECTING THE MEASUREMENT UNITS
a
A choice of measurement units is available ; °C, °F, g/kg, gr/lb. To
select the measurement units, press Menu/Setup/Units.
www.elcometer.com en-6
4 GETTING STARTED (continued)
R
a g/kg and gr/lb relate to ‘Specific Humidity’ measurements only.

The sensors for (a) humidity (RH) and air
temperature (Ta); and (b) surface
temperature (Ts) are located at the top of
the gauge.
Note: The surface temperature sensor is serialised
for calibration traceability purposes.
FOR ACCURATE READINGS
 Do not obstruct airflow through the holes in the casing around
the humidity and air temperature sensors.
 Keep fingers away from the holes - body heat can affect
readings.
 Allow the gauge some time, approximately 20 minutes, to
acclimatise once it is brought from a cold environment into a
warm place and vice versa.
www.elcometer.com
en-7
R
4.6 SETTING MANUAL OR INTERVAL LOGGING
Users can choose to manually log readings - ‘Manual Logging’
(Model S & T) or program the gauge to take readings at set time
intervals and save the readings into the batch memory automatically
- ‘Interval Logging’ (Model T only).
To select ‘Manual Logging’ in immediate mode (Model S & T):
1 Press Menu/Setup/Manual Logging.
2 To select immediate saving of a reading, use the softkeys

to highlight ‘Save only’ and press ‘Sel’.
3 To select holding of a reading followed by an option to save,
use the softkeys to highlight ‘Hold & Save’ and press ‘Sel’.

 The default setting is ‘Hold & Save’.
‘Manual Logging’ is also available when in batching (Model T).
‘Interval Logging’ is only available when in batching (Model T).
For information on creating a new batch with ‘Manual Logging’ or
‘Interval Logging’, see Section 10.1 ‘Creating a New Batch’ on
page en-15.
4 GETTING STARTED (continued)
5 THE SENSORS
a
b

www.elcometer.com en-8
R
TO AVOID DAMAGE
Do not use excessive force when measuring surface
temperature. Light contact between the probe and the surface is
sufficient. Using force does not increase the measuring speed
or improve the accuracy of the measurement, but it does
increase wear and/or damage to the sensor tip.
Do not drag the surface temperature probe over the surface to
avoid excessive wear.
The humidity sensor is fragile and should never be touched. Do
not use compressed air to clean the sensors or the gauge.
If the surface of the humidity sensor becomes saturated with
moisture, allow the moisture to evaporate fully in a dry
environment before using the gauge to take measurements.
Protect the gauge from paint dust and dirt as much as possible
as these can affect the long term accuracy of the humidity
sensor. Always keep the gauge in its protective pouch when not
in use.
Do not wash the sensors in water or with solvents.
5 THE SENSORS (continued)
6 SETTING LIMITS
A lower and/or upper limit can be set by the user for any or all the
climatic parameters.
Limits can be set for individual readings (when not in Batching) or
limits can be set for each batch (when in Batching).
To set limits for individual readings (Model S & T):
1 Press Menu/Set Limits.
2 Use the softkeys to highlight the required parameter and

press ‘Sel’.
3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’

to enable the limit.
4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.


www.elcometer.com
en-9
R
5 Use the softkeys to set the required value and press ‘Ok’

to set or ‘Esc’ to cancel.
6 If required, repeat Steps 3-5 to set and enable a low limit value.
7 Repeat Steps 2-6 for each climatic parameter as required.
To set limits for a batch (Model T):
Limits can be set when a new batch is created. Once a reading is
saved into the batch, limits cannot be amended and limits cannot be
added.
1 Press Batch/New Batch/Limits.
2 Use the softkeys to highlight the required parameter and

press ‘Sel’.
3 Use the softkeys to highlight ‘High Limit on’ and press ‘Sel’

to enable the limit.
4 Use the softkeys to highlight ‘High Limit’ and press ‘Sel’.

5 Use the softkeys to set the required value and press ‘Ok’

to set or ‘Esc’ to cancel.
6 If required, repeat Steps 3-5 to set and enable a low limit value.
7 Repeat Steps 2-6 for each climatic parameter as required.
 Batch limits can be viewed at any time via Batch/Review Batches.
When the value of a parameter falls outside set and enabled limits;
 the appropriate parameter icon flashes;
 If a reading exceeds any set limits during measurement, it will be shown
flashing on the display, even if it has not been selected for display via
Menu/Setup/Display/Select Readings.
 the alarm symbol is displayed next to the parameter;
 the red LED flashes; b
 an audible alarm sounds ;
 when in batching (Model T); a reading which exceeds a high
limit is marked and a reading which exceeds a low limit is
marked .
Note: When the value of the parameter returns within limits, the alarm status is
cleared automatically.
6 SETTING LIMITS (continued)
b The volume of the alarm is determined by the beep volume set via Menu/Setup/Beep Volume

www.elcometer.com en-10
R
7 TAKING A READING
7.1 BEFORE YOU START
1 Press the On/Off button to switch the gauge on - the gauge will
start measuring.
2 Set up the reading display - see Section 4.4 on page en-5.
3 Select the measurement units - see Section 4.5 on page en-6.
4 Set any required limits - see Section 6 on page en-8.
7.2 TAKING A READING IN IMMEDIATE MODE
Follow this procedure to take readings manually (’Manual Logging’)
with the option to save reading data into the rolling memory of the
gauge.
1 Place the rubber tip of the surface temperature sensor against the
surface, preferably at an angle of 90°, and keep it in this position.
 The trend indicator next to the parameter indicates if the value is
increasing ( ) or decreasing ( ). The absence of a trend indicator  
indicates that the value is stable.
2 Press ‘Hold’ followed by ‘Save’ to save the reading data into the
gauge memory.
 If the ‘Manual Logging’ setting is “Save only’, ‘Hold’ is not displayed.
Simply press ‘Save’ to save the reading data into the gauge memory.
To view the statistical analysis of the reading data, press the ‘Stats’
softkey - see Section 9 ‘Statistics’ on page en-14 for further
information.
7.3 TAKING A READING IN BATCH MODE (MODEL T)
Follow this procedure to take readings manually (’Manual Logging’)
or automatically at set time intervals (’Interval Logging’) and save
the reading data into a batch.
Using ‘Manual Logging’:
1 Create a new ‘Manual Logging’ batch - see Section 10.1 on
page en-15.
2 Place the rubber tip of the surface temperature sensor against
the surface, preferably at an angle of 90°, and keep it in this
position.
 The trend indicator next to the parameter indicates if the value is
increasi The absence of a trend indicator ng () or decreasing ().
indicates that the value is stable.

7 TAKING A READING (continued)
www.elcometer.com
en-11
R
3 Press ‘Hold’ followed by ‘Save’ to save the reading data into the
batch memory.
 If the ‘Manual Logging’ setting is “Save only’, ‘Hold’ is not displayed.
Simply press ‘Save’ to save the reading data into the batch memory.
4 To exit batching, press the softkey followed by ‘Exit
Batching’.
Using ‘Interval Logging’:
Before you start, if you intend to take readings over a long period of
time check that the batteries are in good condition; if in doubt, insert
new batteries - .see Section 4.1 ‘Fitting the Batteries’ on page en-4
Consider the use of an external temperature probe; holding the
surface temperature probe integrated into your gauge against a
surface over an extended period of time may not be practical - see
Section 8 ‘Using External Temperature Probes’ on page en-12.
1 Create a new ‘Interval Logging’ batch and set the required
logging time interval - see Section 10.1 on page en-15.
2 Place the rubber tip of the surface temperature sensor against
the surface, preferably at an angle of 90°, and keep it in this
position.
 The trend indicator next to the parameter indicates if the value is
increasi The absence of a trend indicator ng () or decreasing ().
indicates that the value is stable.
3 Press ‘Start’ to start logging, the reading data is saved
automatically at the set interval.
 A delayed start time can be set when creating an ‘Interval Logging’ batch.
The gauge will automatically start once the set time has elapsed.
 If an ‘Auto Switch Off’ time is set, the gauge will appear to switch off after
the set time delay but whilst you are logging, it will remain on in a reduced
power state. In this state, during interval logging, the gauge will continue
reading data into batch memory at the set logging interval. When the
gauge is next switched on, the batch will reopen.
4 Press ‘Stop’ to stop logging data, followed by ‘Yes to confirm or
‘No’ to escape and continue logging.
5 To exit batching, press the softkey followed by ‘Exit
Batching’.

www.elcometer.com en-12
R
7 TAKING A READING (continued)
The Elcometer 319 Model T has a ‘Softkeys Locked’ feature which
provides an additional level of security to prevent accidental
stopping of interval logging. When ‘ Softkeys Locked’ is enabled, an
extra key press is required to stop interval logging.
To enable ‘Softkeys Locked’; press Menu/Setup/Softkeys Locked
followed by ‘Sel’.
To view the statistical analysis of the reading data, press the ‘Batch’
softkey - see Section 11.2 ‘Batch Statistics’ on page en-17 for further
information.
8 USING EXTERNAL TEMPERATURE PROBES
The Elcometer 319 can be fitted with an external, k-type
temperature probe for taking measurements over an extended
period of time - ‘Interval Logging’ (Model T) - or at locations remote
from the gauge.
For details of the external probes available from Elcometer, see
Section 15 ‘Spares & Accessories’ on page en-21.
8.1 FITTING AND EXTERNAL TEMPERATURE PROBE
1 Open the rubber cover (a) which covers
the k-type probe connector at the top of
the gauge.
 There is no need to switch off the gauge before
fitting an external temperature probe.
2 Push the external probe connector into the
socket; never force the connector into the
socket.
 One side of the socket is wider than the other therefore, the external
probe connector will only fit into the socket one way.
Note: When an external probe is fitted, the in-built surface temperature probe is
deactivated.
a

www.elcometer.com
en-13
8 USING EXTERNAL TEMPERATURE PROBES (continued)
R
The Elcometer 319 has a ‘Thermometer Mode’ feature and when
enabled, the gauge only measures and displays the external probe
temperature (Te) - all other functions are disabled.
If ‘Thermometer Mode’ is enabled and an external temperature
probe is not fitted, the gauge will display an error reading ‘---’.
To enable ‘Thermometer Mode’; press Menu/Temperature Mode,
followed by ‘Sel’.
The connection of an external probe is indicated on the display:
 If ‘Thermometer Mode’ is enabled, the display shows and
Te;
 If ‘Thermometer Mode’ is not enabled, the display shows
and Ts.
8.2 PREPARING THE GAUGE FOR USE WITH AN EXTERNAL
PROBE
The Elcometer 319 supports external temperature
measurements with a suitable probe from -40° to 200°C
(-40°F to 392°F) however, the gauge is only rated between
-20° to 80°C (-4°F to 176°F) and should not be exposed to
temperatures outside this range.
 If a magnetic surface is available, attach the gauge to
the surface using the magnets built into the back of the gauge.
Ensure the gauge is attached securely before use.
 If the external temperature probe is magnetic, attach the probe
to the magnetic surface.
 If the external temperature probe is for measuring liquids, place
the probe tip in the liquid.
Note: If the temperature of the external temperature probe exceeds the range of
the gauge, there is no error message or warning but the reading value will
be saved as ‘---’.

www.elcometer.com en-14
R
9 STATISTICS
The Elcometer 319 can display statistics for readings saved in the
10 reading rolling memory (Model S & T) or batch memory
(Model T).
Press the ‘Stats’ softkey to view the statistics for readings saved in
rolling memory.
The following statistical values are displayed. Press the right hand
softkey to view the statistics for the next parameter. Press ‘Clear’ to
delete the statistics.
 Number of readings (n:)
 Average reading (X:)
 Lowest reading (Lo:)
 Highest reading (Hi:)
 Standard Deviation (σ:)
 Coefficient of Variation (COV:)
When in the statistics review screen, pressing the ‘Rdgs’ softkey
displays the reading value and date and time of each reading saved
in rolling memory. Press the right hand softkey to view the readings
for the next parameter.
The appropriate limit icon is displayed next to readings outside any
enabled limits, if the reading is below the low limit and if above
the high limit.
To view the readings and statistics for a batch (Model T) - see
Section 11 ‘ Reviewing Batch Data’ on page en-17.

www.elcometer.com
en-15
R
The Elcometer 319 Model S & T have a 10 reading rolling memory.
The Model T can also store up to 25,000 sets of readings in up to
999 batches. The following batch functions are available:
 Batch/New Batch; Creates a ‘Manual Logging’ or ‘Interval
Logging’ batch - see Section 10.1 ‘Creating a New Batch’ on
page en-15.
 Batch/Open Existing Batch; Open an existing batch.
 Batch/Review Batches; Review the batch information,
readings and statistics - see Section 11 ‘Reviewing Batch Data’
on page en-17.
 Batch/Copy Batch; Copy a batch including the batch header
information.
 Batch/Delete; Delete a single batch or all batches entirely from
the gauge.
10.1 CREATING A NEW BATCH
Users can create a ‘Manual Logging’ batch or an ‘Interval Logging’
batch:
 ‘Manual Logging; readings are manually saved into the batch
by the user.
 ‘Interval Logging’; the gauge is programmed to take readings
at set time intervals and readings are saved into the batch
memory automatically.
To create a ‘Manual Logging’ batch:
1 Press Menu/Batch/New Batch.
2 If ‘Manual Logging Batch’ is not displayed on screen, press the
softkey to select ‘Manual Logging’.
 The icon will be displayed on the main reading screen indicating that
‘Manual Logging’ is enabled.
3 Press ‘Limits’ to set any required limits for the batch - see
Section 6 ‘Setting Limits’ on page en-8.
4 Press ‘Ok’ to create the batch or ‘Esc’ to cancel.
 When a batch is open, the ‘Batch’ softkey is replaced by . Press
to return to the Batch Menu.
10 BATCHING - MODEL T

To create an ‘Interval Logging’ batch:
1 Press Menu/Batch/New Batch.
2 If ‘Interval Logging Batch’ is not
displayed on screen, press the
softkey to select ‘Interval Logging’
followed by ‘Ok’.
 The icon will be displayed on the main
reading screen indicating that ‘Interval
Logging’ is enabled.
3 Use the sofkeys to set the

required time interval, between
1 second and 24 hours, followed by
‘Ok’ to set.
 The approximate number of readings which
can be taken and saved in the batch
together with the approximate number of
days it will take to take those readings at the
time interval set is displayed.
4 If required, use the sofkeys to set

the required delayed start time,
between 1 and 60 minutes or ‘Off’,
followed by ‘Ok’ to set.
5 Press ‘Start’ to initiate logging.
 If a delayed start time has been set, the
countdown will begin when ‘Start’ is pressed.
The icon will be displayed on screen,
changing to when the set delay has
elapsed and the gauge starts logging
readings.
 When a batch is open, the ‘Batch’ softkey is replaced by . Press
to return to the Batch Menu.
www.elcometer.com en-16
R
10 BATCHING - MODEL T (continued)

11.1 BATCH READINGS
To view the batch readings:
1 Press Batch/Review Batches
 If already in a Batch, press
followed by ‘Review Batches’.
2 Use the sofkeys to select

the required batch, followed by
‘Sel’ to select.
3 Press ‘Rdgs’ the view the batch
readings.
4 Press ‘Back’ to return to the
batch menu.
The date and time of each reading
together with the reading value is
displayed. Press the softkeys to

scroll through the readings and the
right hand softkey to view the readings
for the next parameter.
The appropriate limit icon is displayed next to readings outside any
enabled limits, if the reading is below the low limit and if above
the high limit.
11.2 BATCH STATISTICS
To view the batch statistics:
1 Press Batch/Review Batches
 If already in a Batch, press
followed by ‘Review Batches’.
2 Use the sofkeys to select

the required batch, followed by
‘Sel’ to select.
3 Press ‘Stats’ the view the batch
statistics.
4 Press ‘Back’ to return to the
batch menu.
 If in an ‘Interval Logging’ batch,
logging is halted whilst statistics are
displayed. Logging recommences
when ‘Back’ is pressed.
www.elcometer.com
en-17
11 REVIEWING BATCH DATA - MODEL T
R

www.elcometer.com en-18
11 REVIEWING BATCH DATA - MODEL T (continued)
R
The following statistical values are displayed. Press the right hand
softkey to view the statistics for the next parameter.
 Number of readings in the batch (n:)
 Average reading for the batch (X:)
 Lowest reading in the batch (Lo:)
 Highest reading in the batch (Hi:)
 Standard Deviation (σ:)
 Coefficient of Variation (COV:)
12 MENU STRUCTURE - MODEL S
Menu
Delete Last Reading
Backlight
Thermometer Mode
Set Limits
View Time & Date
Setup
Reset
About
SET LIMITS
RH
Ts
Ta
Td
TΔ
SH
SETUP
Units
Languages
Auto Switch Off
Time & Date
Beep Volume
Display
Manual Logging
User Screen
Setup Backlight
○
○
High Limit on
High Limit
Low Limit on
Low Limit
○
○
UNITS
°C, g/kg
°F, gr/lb
○
○
DISPLAY
Select Readings
Main Reading
SELECT READINGS
RH
Ts
Ta
Td
TΔ
Tdb
Twb
SH
MANUAL LOGGING
Save Only
Hold & Save
○
○
○
ABOUT
Gauge Information
Contact
Help
Legal
Stats SETUP BACKLIGHT
Backlight
Backlight Timeout
Backlight Brightness
○BACKLIGHT BRIGHTNESS
Low
Medium
High
○
○
○
LEGAL
Legal Notices
Regulatory REGULATORY
xxxxx

www.elcometer.com
en-19
13 MENU STRUCTURE - MODEL T
R
Menu
Delete Last Reading
Backlight
Thermometer Mode
Set Limits
View Time & Date
Setup
Reset
Bluetooth
About
SET LIMITS
RH
Ts
Ta
Td
TΔ
SH
SETUP
Units
Languages
Auto Switch Off
Time & Date
Beep Volume
Display
Manual Logging
Softkeys Locked
User Screen
Setup Backlight
BLUETOOTH
Enable
Gauge ID xxxxxx-xxx
Authentication xxxxx
○
○
○
High Limit on
High Limit
Low Limit on
Low Limit
○
○
UNITS
°C, g/kg
°F, gr/lb
○
○
DISPLAY
Select Readings
Main Reading
SELECT READINGS
RH
Ts
Ta
Td
TΔ
Tdb
Twb
SH
MANUAL LOGGING
Save Only
Hold & Save
○
○
○
○
ABOUT
Gauge Information
Contact
Help
Legal
BATCH
Exit Batching
New Batch
Open Existing Batch
Review Batches
Copy Batch
Delete
Free Memory xx.x%
○
DELETE
Single Batch
All Batches
Stats SETUP BACKLIGHT
Backlight
Backlight Timeout
Backlight Brightness
○BACKLIGHT BRIGHTNESS
Low
Medium
High
○
○
○
14 DOWNLOADING DATA - MODEL T
14.1 DOWNLOADING DATA USING ELCOMASTER®
®
Using ElcoMaster - supplied with each gauge and available as a
free download at elcometer.com - gauges can transmit readings to a
PC for archiving and report generation. Data can be transferred via
® ®
USB or Bluetooth . For more information on ElcoMaster visit
www.elcometer.com
14.2 DOWNLOADING DATA USING ELCOMASTER MOBILE
®
APPS ®
Ideal when out in the field or on-site, using the ElcoMaster
Android™ or iOS Mobile App users can:
 Store live readings directly on to a mobile device and save
them into batches together with GPS coordinates.
 Add photographs of the test surface.
 Inspection data can be transferred from mobile to PC for further
analysis and reporting.
®
For more information on ElcoMaster Mobile Apps visit
www.elcometer.com
LEGAL
Legal Notices
Regulatory
REGULATORY
QDID xxxxx
xxxxx
xxxxx
xxxxx