Eldat RTS07 User manual

Press the OK button.
The weekday blinks on
the display.
Now select the respective day with the UP
and DOWN buttons.
Press the OK button
again. The settings are
saved and the Time
Switch returns to
Operating Mode.
The Time Switch RTS07 is a wall-mounted battery-
operated radio timer (surface-mounted). Radio
Time Switch switching Easywave radio
controls (function range: UP/STOP/DOWN)
ent
The Radio Time Switch has four individually coded
radio channels so that four different radiograms can be
sent to control four devices or groups individually
It is possible to transmit the four different radiograms
together (with a delay of approx. 0.5 seconds per
channel) and therefore activate all four devices or
groups simultaneously (group function).
The following four operating modes are available:
Radio Time Switch.
Time Switch
Time Switch
The
allows
depend on time and/or brightness. Brightness
control is only possible in connection with the Radio
Light Sensor SL01.
.
Time-Controlled:
Automatic Operation: Blinds are raised and lowered
either at the programmed switching times or manually.
Automatic Operation with Partially Manual
Operation: The programmed switching times as well
as the sun protection/twilight mode functions are
deactivated until 24:00 hrs. After 24:00 hrs, the timer
switches to automatic mode.
Brightness-Controlled:
(only in connection with Radio Light Sensor SL01)
Solar Protection Mode: If a set brightness value is
exceeded, the blinds lower to a desired shade
position.
Twilight mode: If a set brightness value is undercut,
the blinds are lowered completely.
Manual Mode: Raising and lowering of blinds only by
pushing the button on the
The offers the following additional
functions:
Holiday Mode: On holidays, you can activate the
switching times programmed for Sundays with only
one push of a button.
Switching from Normal to Daylight Savings Time:
You can switch the from normal to
daylight savings time with just one push of a button.
Vacation Mode: Shutters/blinds are raised or lowered
with a time delay of ± 15 minutes compared to the
programmed switching times in automatic mode. This
way you can make your house appear inhabited.
Display Overview
AUTO
MANU
W
AM
PM
S
MO TU WE TH FR SA SU
Weekday
(B1)
Battery capacity (E)
Move to
intermediate
position
(C2.2, C4.1)
Winter/daylight
saving time (D2)
Hour-
format (B1)
Radio channel (B2, C6)
Operating
mode (C5)
Direction (C2.2,
C4.1)
Setting current
time (B1)
Holiday
timer (D3)
Twilight-
mode (C3)
Solar protection
mode (C2)
Time/Radio chan-
nell/Numerical value
Function
Model
B1 Setting the Time and Weekday
B Basic Settings
If you do not press a button within 5 minutes during
programming, the t s automatically returns to
operating mode.
With ESC you can
cancel all programming
steps at any time and
return to operating
mode.
In this case the settings are not saved.
ime witch
Operating the Radio Time Switch
The following settings have to be made to put the
control into operation and for later modifications:
Seite
A Mounting the Radio Time Switch. . . . . . . . . . . 1
B Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 1
B1 Setting the Time/Weekday. . . . . . . . . . . . . 1
B2 1
B3 Measuring and Saving the Runtimes. . . . . 2
B4 Putting the Light Sensor into Operation. . . 2
C Operating Shutters/Blinds . . . . . . . . . . . . . . . . 2
C1 Factory Settings. . . . . . . . . . . . . . . . . . . . . 2
C2 Solar Protection Mode. . . . . . . . . . . . . . . . 2
C2.1 Setting the Brightness Value...........2
C2.2 Setting the Intermediate Position........2
C2.3 Activating Solar Protection Mode .......2
C3 Twilight Mode.......................2
C3.1 Setting the Twilight Value . . . . . . . . . . . . . 2
C3.2 Activating Twilight Mode . . . . . . . . . . . . . . 3
C4 Automatic Mode. . . . . . . . . . . . . . . . . . . . . 3
C4.1 Programming new Switching Times
and Intermediate Positions ............3
C4.2 Deleting Switching Times . . . . . . . . . . . . . 3
C4.3 Changing Switching Times ............3
C5 Changing the Operating Mode .........4
C6 Manual Mode. . . . . . . . . . . . . . . . . . . . . . . 4
DAdditional Functions ....................4
D1 Activating Holiday Mode . . . . . . . . . . . . . . 4
D2 Switching Between Normal Time
and Daylight Savings Time ............4
D3 Vacation Mode
D4 Deleting all Data (Reset) . . . . . . . . . . . . . . 4
E ....................4
FTroubleshooting.........................4
GGeneral Information .....................4
Memorizing Radio Channels
in the Controls . . . . . . . . . . . . . . . . . . . . . .
Changing the Battery
Setting Daylight Savings Time:
Setting/Changing the Time:
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Press the S/W button to switch between
daylight savings and normal time.
The display switches
between Wand S.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
HOLI
S/W DEL
W
MO TU•WE• •FR SA SOTH
S
Setting the Hour Format (12-/24 hours):
Press the MODE button
for more than 3 seconds.
The hour format switches
between 12 hour display
(AM/PM) and 24 hour
display.
PM
MO TU•WE• •FR SA SOTH
AM
Setting the eekday:W
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
MO TU•WE• •FR SA SOTH
W
SA SO
MO Monday
TU Tuesday
WE Wednesday
TH Thursday
FR Friday
SA Saturday
SU Sunday
OK
ESC
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
Press the CLOCK button
for more than 3 seconds.
The time on the display
starts to blink.
Set the time with the UP or DOWN button.
Advancing
the minutes Resetting the minutes
W
MO TU•WE• •FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
MODE
PROG
A Mounting the Radio Time Switch
. Mount the wall mount with the enclosed screws
and dowels on the desired installation site
Avoid installing the time switch in one of
the following sites as this may impair
the range of the transmitter: in a
distribution box or a metal casing, in
direct proximity to large metal objects
and on the floor or close to it.
CR2032
+
The codes for each radio channel must be memorized
in the radio controls first, so that the radio controls can
receive the transmission code of the clock. Memorizing
the codes in the group function is not possible.
Set the control into programming mode. For this, read
the operating instructions of the radio controls.Select
the favoured radio channel of the control in the time
switch and transfer the Easywavecode to the radio
control:
B2 Memorizing Radio Channels
in the Controls
The following settings are available in automatic mode
and vacation mode:
-Day Function: Switching period 24 hours or
Week Function: Switching period one week
-Individual Switching Times: Different switching
times can be programmed for each weekday or
groups of weekdays.
-Intermediate Position: Lowering of blinds/
shutters to a desired shade position.
The Radio Time Switch RTS07 was exclusively
developed and manufactured for the brightness
time-controlled switching of devices with Easywave
radiocontrols.
and
The manufacturer will not be liable for damage caused
by improper or inappropriate use.
Intended Use
UP
DOWN
STOP
W
MO TU•WE• •FR SA SOTH
Insert the enclosed
battery.
Make sure the
Polarity is correct!
Replace the time switch in the wall mount. The
snap catches have to lock.
1/4
GB Radio Time Switch RTS07
RTS07E5004-01

Press OK again and the
weekday blinks on the
display.
Select a new weekday with UP or
DOWN.
Set the time switch to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time to be
deleted with UP or DOWN.
Press the DEL button for more than 3
seconds. The switching time is deleted
and the display shows the memory slots
again. Return to operating mode with
ESC.
Press OK briefly. The
direction of the shutter
motion blinks on the
display. With UP or DOWN you can select
which direction the changed
switching time is supposed to
apply to.
The intermediate position
blinks on the display.
Enter a new value in 5% steps
with UP or DOWN.
Set the t s into operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode ADJ.
Press the OK button.
The display shows the
last channel.
Press the CH button to select
the desired channel (shutter).
ime witch
Briefly press the OK
button. The saved
switching time is displayed.
Press ESC to return to
operatingmode.
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
C Operating Shutters/Blinds
B3 Measuring and Saving the Runtimes
B4 Putting the Light Sensor into Operation
C2.1 Setting the Brightness Value
Factory setting for channel CH1 is the automatic mode
without intermediate position. The following switching
times are pre-programmed:
-Shutter rises completely Monday through Sunday
at 7:00 hrs,
-Shutter closes completely Monday through Sunday
at 21:00 hrs.
Practical preset values are also programmed for
solarprotection and twilight mode.
The shutters can also be raisedor lowered manually in
all operating modes by pressing abutton on the
t s .
If the shutter raises or lowers
automatically, you can stop it by briefly
pressing the STOP button.
ime witch
For moving the shutter/blind into a desired shade
position, the has to measure and save
the runtime for raising and lowering the shutters
once.
time switch
Keep the UP button
depressed until the
shutter is completely
open.
The raising time is
measured and saved.
Press ESC twice to
return to operating
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
W
MO TU•WE• •FR SA SOTH
Press the DOWN button
to change back to the
Setup Mode. You can
either make further
adjustments
or
press ESC to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ESC
Here you can define how far the shutters are to be
lowered for solar protection.
If an intermediate position is programmed, the shutter
first moves to the top end position and then into the
desired intermediate position.
When making your setting, make sure
that the shutter does not obscure the light
sensor in the shade position.
The twilight mode is now active. The shutter lowers
completely when the measured brightness is less than
the set value for approx. 6 minutes. However,
beforehand the brightness level must have been
higher than the set value for more than one hour .
The shutter is not raised again automatically in twilight
mode. Open the shutter manually or use a switching
time programmed for automatic mode.
In case the radio reception between the time
switch and the light sensor is disrupted the
moon icon blinks (see also operating
instructions of the Light Sensor SL01).
If the disruption persists for more than 45
minutes, the Twilight Protection Mode is
automatically turned off.
To reactive this function, press the
SUN/MOON button.
Press the OK button. The
right value starts to blink
on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the twilight value on a time of day
at which the brightness has the value at
which you want to lower the shutters or
orient yourself on the currently measured
value. If you want to update the measured
value once again beforehand, briefly press
the connection button on the light sensor.
OK
If the timer is in operating mode, you can now activate
twilight mode.
Briefly press the
SUN/MOON button;
the display shows the
moon icon.
ADJ
Press the UP button to
change to the setup mode.
You can either make
further adjustments
or
press ESC to return to operating mode.
W
MO TU•WE• •FR SA SOTH
ESC
C3.2 T MActivating wilight ode
To be able to use the automatic operation modes, the
switching times and the intermediate positions for the
shade position have to be programmed.
To do so, change to programming mode. If you do not
press a button in programming mode within 5 minutes,
the time switch automatically returns to operating
mode.
The switching times programmed in automatic mode
take precedence over the settings for solar protection
or twilight mode. You can program 50 switching times
altogether.
If the timer is set to 12-hour display, the switching
times are also displayed in 12-hour format.
PROG
MODE
C4.2 S TDeleting witching imes
C4.3 S TChanging witching imes
HOLI
S/W DEL
AUTO
C4.1 S T
and Intermediate Positions
Programming witching imes
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
Set the time switch to operating mode (ESC).
Press the PROG button for
more than 3 seconds. The
display shows the free
memory slots.
Select the switching time you want
to change with UP or DOWN.
Briefly press the OK
button. The switching time
starts to blink on the
display.
Set a new switching time with UP
or DOWN.
Set the time switch to operating mode (ESC).
Press the PROG button
for more than 3 seconds
to change to Programming
Mode. The display shows
the free memory slots on
the right.
Briefly press the OK
button. The switching time
starts to blink on the
display.
If the display shows
FULL, the memory for the
switching times is full.
Delete a time setting
before programming.
Set a new switching time with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO Monday
TU Tuesday
WE Wednesay
TH Thursay
FR Friday
SA Saturday
SU Sunday
Press OK again and the
weekdays blink on the
display.
Select the weekday or a
combination of weekdays with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO-FR Monday to Friday
SA-SU Saturday and Sunday
MO-SU daily (day function)
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press the OK button
again. The channel no.
starts to blink on the
display.
Select a new channel or the
group function ALL with UP or
DOWN.
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Briefly press the OK
button. The channel
starts to blink on the
display. Select a new channel with
UP or DOWN.
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press OK again. The
direction of the shutter
motion blinks on the
display. With UP or DOWN you can
select which direction the
changed switching time is
supposed to apply to.
LOWER
RAISE
OK
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Briefly press the OK
button. The saved
switching time is
displayed.
Press ESC to return to operating
mode.
OK
OK
ESC
ESC
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Raise the shutter completely
with the UP button.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
OK CH
CLOCK
Keep the DOWN button
depressed until the
shutter is completely
closed.
The lowering time is
measured and saved.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
To be able to use solar protection and
twilight mode, you have to establish the
radio connection between the light sensor
and the t s .
For this,read the operating instructions of
the Radio Light Sensor SL01.
ime witch
C2 P MSolar rotection ode
Solar protection mode can only be activated when the
shutter was completely raised with theTime Switch
either manually or automatically. Do not interrupt the
raising procedure with the STOP button.
The radio connection between the light sensor and the
time switch must be established.
If you want to move the shutter to a certain shade
position, please program the intermediate position.
Here you can program the value for the brightness at
which your shutter is to move to the desired shade
position.
We recommend initially using the factory settings.
Press the UP button.
The display shows two
brightness values.
The left figure is the currently measured
value, the right one the default value or an
already programmed value.
With the CH button you
can check, which channel
is selected.
Press the CH button again to show the
brightness value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Press the OK button.
The right value starts to
blink on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the brightness value on a time of
day at which the sun is so intense that you
want to lower the shutters or orient yourself
on the currently measured value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
OK
Set the time switch to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
Press the OK button
again. The selected
channel starts to blink on
the display.
Select a new channel with UP or
DOWN.
To confirm the setting
press the OK button again.
The display shows the
programmed value.
Press the OK button
again. The selected
channel starts to blink
on the display.
Select a new channel with UP
or DOWN
To confirm the setting
press the OK button again.
The display shows the
programmed value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
OK
OK
OK
OK
Set the Time Switch to Operating Mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Press the UP button
twice. The display shows
the current value for the
intermediate position as
well as the symbols for
the direction and the
intermediate position.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ADJ
2x
Press the OK button. The
value starts to blink on the
display.
Select a new value in 5% steps
with UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
100%
25% 75%
0%
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
If the Time Switch is in Operating Mode, you can
activate the Solar Protection Mode.
Briefly press the
SUN/MOON button;
the display shows
the sun icon.
ADJ
W
AUTO
MO TU WE FR SA SOTH
Now the solar protection mode is activated.If the
measured brightness value is equal or larger than the
set value for approx. 12 minutes, the shutter lowers to
the shade position. (see C2.2, "Setting the
Intermediate Position"). If the measured value falls
below half of the set value for approx. 30 minutes, the
shutter opens completely again.
The sun icon blinks if the radio reception
between the time switch and the light sensor
is disrupted (see also the operating
instructions of the Light Sensor SL01).
If the disruption persists for more than 45
minutes, the Solar Protection Mode is
automatically turned off.
To reactive this function, press the
SUN/MOON button.
ESC
To confirm the setting
press the OK button.The
display shows the
programmed value.
Press the UP button twice
to change to the setup
mode. You can either
make further adjustments
or
press ESC to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
2x
2x
AUTO
MO TU WE TH FR SA SU• • •
Press the UP button three
times. The display shows
two brightness values and
the moon icon. The left
figure is the currently
measured value, the right one the default
value or an already programmed value.
With the CH button you
can check, which channel
is selected.
Press the CH button
again. The display shows the twilight value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
3x
C3.1 T VSetting the wilight alue
Here you can program the value for the brightness at
which your shutter is to be closed.
We recommend initially using the factory settings.
C3 MTwilight ode
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter C2.2)
The intermediate position is
programmed and indicated with the
two direction arrows.
AUTO
MO TU WE TH FR SA SU
+
C1 Factory Settings C2.2 Setting the Intermediate Position
C2.3 Activating Solar Protection Mode
2/4 3/4
Press the CH button
shortly. The display
shows channel CH1. By
pressing the CH button
repeatedly the desired
channel can be selected.
Keep the UP button
depressed shortly.
The code is transferred to
the control.
Repeat the procedure for each channel
(shutter or other devices).
W
MANU
MO TU WE FR SA SOTH
MO•TU WE• •FR SA SO•TH
MANU
W
MANU
W
W
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MANU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
CR2032
+
CR2032
+
Set the t s to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the Setup
Mode.
ime witch
C4 Automatic Mode

Press OK again and the
weekday blinks on the
display.
Select a new weekday with UP or
DOWN.
Set the time switch to operating mode (ESC).
Press the PROG button
for more than 3 seconds.
The display shows the
free memory slots.
Select the switching time to be
deleted with UP or DOWN.
Press the DEL button for more than 3
seconds. The switching time is deleted
and the display shows the memory slots
again. Return to operating mode with
ESC.
Press OK briefly. The
direction of the shutter
motion blinks on the
display. With UP or DOWN you can select
which direction the changed
switching time is supposed to
apply to.
The intermediate position
blinks on the display.
Enter a new value in 5% steps
with UP or DOWN.
Set the t s into operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode ADJ.
Press the OK button.
The display shows the
last channel.
Press the CH button to select
the desired channel (shutter).
ime witch
Briefly press the OK
button. The saved
switching time is displayed.
Press ESC to return to
operatingmode.
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
C Operating Shutters/Blinds
B3 Measuring and Saving the Runtimes
B4 Putting the Light Sensor into Operation
C2.1 Setting the Brightness Value
Factory setting for channel CH1 is the automatic mode
without intermediate position. The following switching
times are pre-programmed:
-Shutter rises completely Monday through Sunday
at 7:00 hrs,
-Shutter closes completely Monday through Sunday
at 21:00 hrs.
Practical preset values are also programmed for
solarprotection and twilight mode.
The shutters can also be raisedor lowered manually in
all operating modes by pressing abutton on the
t s .
If the shutter raises or lowers
automatically, you can stop it by briefly
pressing the STOP button.
ime witch
For moving the shutter/blind into a desired shade
position, the has to measure and save
the runtime for raising and lowering the shutters
once.
time switch
Keep the UP button
depressed until the
shutter is completely
open.
The raising time is
measured and saved.
Press ESC twice to
return to operating
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ESC
W
MO TU•WE• •FR SA SOTH
Press the DOWN button
to change back to the
Setup Mode. You can
either make further
adjustments
or
press ESC to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ESC
Here you can define how far the shutters are to be
lowered for solar protection.
If an intermediate position is programmed, the shutter
first moves to the top end position and then into the
desired intermediate position.
When making your setting, make sure
that the shutter does not obscure the light
sensor in the shade position.
The twilight mode is now active. The shutter lowers
completely when the measured brightness is less than
the set value for approx. 6 minutes. However,
beforehand the brightness level must have been
higher than the set value for more than one hour .
The shutter is not raised again automatically in twilight
mode. Open the shutter manually or use a switching
time programmed for automatic mode.
In case the radio reception between the time
switch and the light sensor is disrupted the
moon icon blinks (see also operating
instructions of the Light Sensor SL01).
If the disruption persists for more than 45
minutes, the Twilight Protection Mode is
automatically turned off.
To reactive this function, press the
SUN/MOON button.
Press the OK button. The
right value starts to blink
on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the twilight value on a time of day
at which the brightness has the value at
which you want to lower the shutters or
orient yourself on the currently measured
value. If you want to update the measured
value once again beforehand, briefly press
the connection button on the light sensor.
OK
If the timer is in operating mode, you can now activate
twilight mode.
Briefly press the
SUN/MOON button;
the display shows the
moon icon.
ADJ
Press the UP button to
change to the setup mode.
You can either make
further adjustments
or
press ESC to return to operating mode.
W
MO TU•WE• •FR SA SOTH
ESC
C3.2 T MActivating wilight ode
To be able to use the automatic operation modes, the
switching times and the intermediate positions for the
shade position have to be programmed.
To do so, change to programming mode. If you do not
press a button in programming mode within 5 minutes,
the time switch automatically returns to operating
mode.
The switching times programmed in automatic mode
take precedence over the settings for solar protection
or twilight mode. You can program 50 switching times
altogether.
If the timer is set to 12-hour display, the switching
times are also displayed in 12-hour format.
PROG
MODE
C4.2 S TDeleting witching imes
C4.3 S TChanging witching imes
HOLI
S/W DEL
AUTO
C4.1 S T
and Intermediate Positions
Programming witching imes
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
Set the time switch to operating mode (ESC).
Press the PROG button for
more than 3 seconds. The
display shows the free
memory slots.
Select the switching time you want
to change with UP or DOWN.
Briefly press the OK
button. The switching time
starts to blink on the
display.
Set a new switching time with UP
or DOWN.
Set the time switch to operating mode (ESC).
Press the PROG button
for more than 3 seconds
to change to Programming
Mode. The display shows
the free memory slots on
the right.
Briefly press the OK
button. The switching time
starts to blink on the
display.
If the display shows
FULL, the memory for the
switching times is full.
Delete a time setting
before programming.
Set a new switching time with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
PROG
MODE
AUTO
AUTO
MO TU WE TH FR SA SU
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO Monday
TU Tuesday
WE Wednesay
TH Thursay
FR Friday
SA Saturday
SU Sunday
Press OK again and the
weekdays blink on the
display.
Select the weekday or a
combination of weekdays with
UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
MO-FR Monday to Friday
SA-SU Saturday and Sunday
MO-SU daily (day function)
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press the OK button
again. The channel no.
starts to blink on the
display.
Select a new channel or the
group function ALL with UP or
DOWN.
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Briefly press the OK
button. The channel
starts to blink on the
display. Select a new channel with
UP or DOWN.
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press OK again. The
direction of the shutter
motion blinks on the
display. With UP or DOWN you can
select which direction the
changed switching time is
supposed to apply to.
LOWER
RAISE
OK
AUTO
MO TU WE TH FR SA SU
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Briefly press the OK
button. The saved
switching time is
displayed.
Press ESC to return to operating
mode.
OK
OK
ESC
ESC
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Raise the shutter completely
with the UP button.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
OK CH
CLOCK
Keep the DOWN button
depressed until the
shutter is completely
closed.
The lowering time is
measured and saved.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
To be able to use solar protection and
twilight mode, you have to establish the
radio connection between the light sensor
and the t s .
For this,read the operating instructions of
the Radio Light Sensor SL01.
ime witch
C2 P MSolar rotection ode
Solar protection mode can only be activated when the
shutter was completely raised with theTime Switch
either manually or automatically. Do not interrupt the
raising procedure with the STOP button.
The radio connection between the light sensor and the
time switch must be established.
If you want to move the shutter to a certain shade
position, please program the intermediate position.
Here you can program the value for the brightness at
which your shutter is to move to the desired shade
position.
We recommend initially using the factory settings.
Press the UP button.
The display shows two
brightness values.
The left figure is the currently measured
value, the right one the default value or an
already programmed value.
With the CH button you
can check, which channel
is selected.
Press the CH button again to show the
brightness value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI Press the OK button.
The right value starts to
blink on the display.
Select a new value with UP or
DOWN in a range between 0
and 29.
Program the brightness value on a time of
day at which the sun is so intense that you
want to lower the shutters or orient yourself
on the currently measured value.
If you want to update the measured value
once again beforehand, briefly press the
connection button on the light sensor.
OK
Set the time switch to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
Press the OK button
again. The selected
channel starts to blink on
the display.
Select a new channel with UP or
DOWN.
To confirm the setting
press the OK button again.
The display shows the
programmed value.
Press the OK button
again. The selected
channel starts to blink
on the display.
Select a new channel with UP
or DOWN
To confirm the setting
press the OK button again.
The display shows the
programmed value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
OK
OK
OK
OK
Set the Time Switch to Operating Mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the setup
mode.
Press the UP button
twice. The display shows
the current value for the
intermediate position as
well as the symbols for
the direction and the
intermediate position.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ADJ
2x
Press the OK button. The
value starts to blink on the
display.
Select a new value in 5% steps
with UP or DOWN.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
100%
25% 75%
0%
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
If the Time Switch is in Operating Mode, you can
activate the Solar Protection Mode.
Briefly press the
SUN/MOON button;
the display shows
the sun icon.
ADJ
W
AUTO
MO TU WE FR SA SOTH
Now the solar protection mode is activated.If the
measured brightness value is equal or larger than the
set value for approx. 12 minutes, the shutter lowers to
the shade position. (see C2.2, "Setting the
Intermediate Position"). If the measured value falls
below half of the set value for approx. 30 minutes, the
shutter opens completely again.
The sun icon blinks if the radio reception
between the time switch and the light sensor
is disrupted (see also the operating
instructions of the Light Sensor SL01).
If the disruption persists for more than 45
minutes, the Solar Protection Mode is
automatically turned off.
To reactive this function, press the
SUN/MOON button.
ESC
To confirm the setting
press the OK button.The
display shows the
programmed value.
Press the UP button twice
to change to the setup
mode. You can either
make further adjustments
or
press ESC to return to operating mode.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
OK
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI
2x
2x
AUTO
MO TU WE TH FR SA SU• • •
Press the UP button three
times. The display shows
two brightness values and
the moon icon. The left
figure is the currently
measured value, the right one the default
value or an already programmed value.
With the CH button you
can check, which channel
is selected.
Press the CH button
again. The display shows the twilight value.
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
3x
C3.1 T VSetting the wilight alue
Here you can program the value for the brightness at
which your shutter is to be closed.
We recommend initially using the factory settings.
C3 MTwilight ode
AUTO
MO TU WE TH FR SA SU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/W DEL
HOLI Press UP and DOWN at
the same time. The
intermediate position
blinks on the display.
Select a new value in 5% steps
with UP or DOWN. (Also see
chapter C2.2)
The intermediate position is
programmed and indicated with the
two direction arrows.
AUTO
MO TU WE TH FR SA SU
+
C1 Factory Settings C2.2 Setting the Intermediate Position
C2.3 Activating Solar Protection Mode
2/4 3/4
Press the CH button
shortly. The display
shows channel CH1. By
pressing the CH button
repeatedly the desired
channel can be selected.
Keep the UP button
depressed shortly.
The code is transferred to
the control.
Repeat the procedure for each channel
(shutter or other devices).
W
MANU
MO TU WE FR SA SOTH
MO•TU WE• •FR SA SO•TH
MANU
W
MANU
W
W
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MANU
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
CLOCK
CR2032
+
CR2032
+
Set the t s to operating mode (ESC).
Press the ADJ button for
more than 3 seconds to
change to the Setup
Mode.
ime witch
C4 Automatic Mode

Set the time switch to operating mode (ESC).
Press the CH button
repeatedly until the
correct channel is
displayed.
Press the UP, DOWN or
STOP button; the shutter
moves in the desired
direction or stops.
Set the time switch to operating mode (ESC).
Press MODE until the
dice appears on the
display.
In vacation mode, the holiday mode is
deactivated with a random offset of ±15
minutes.
Set the time switch to operating mode (ESC).
Switch the holiday
mode ON or OFF by
pressing the HOLI
button.
The weekday SU
blinks on the display.
If you have activated the holiday mode
prior to 18:00 hrs, it is automatically
deactivated at 24:00 hrs ofthe same
day.
If you have activated the holiday mode
after 18:00 hrs, it is first automatically
deactivated at 24:00 hrs on the next
day.
.
In vacation mode, the holiday mode is
deactivated with a random difference of 15
minutes
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
Disposal
Conformity
Customer Service
Technical Details
E Exchanging the Battery
FTroubleshooting
Dispose of used batteries in a recycling bin
for batteries or via the specialist trade.
Put the packaging material into the recycling
bins for cardboard, paper and plastics.
If, despite correct handling, faults or malfunctions occur
or if the product was damaged, please contact your
retailerorthemanufacturer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: [email protected]
Dispose of the waste product via a collection
point for electronic scrap or via your specialist
dealer.
Waste electrical products and batteries should not
be disposed of with household waste!
Hereby, ELDAT GmbH declares that the radio
equipment type RTS07 is in compliance with
Directive 2014/53/EU.
The full text of the EU declaration of conformity
is available at the following internet address:
www.eldat.de
Frequency:
Radiated power: 0.43 mW
Modulation: FSK
Coding: Easywave
: 1x 3 V- , CR2032
:
- 13 µA
- for a long faulty radio re-
ception of the Light Sensor 510 µA
(max. 20 min)
- 14 mA
: 0°C bis 50°C
:
- 150 m
- 30 m
: 80 x 80 x 16 mm
: 50 g
868,30 MHz
Voltage supply battery
Power consumption
Static current approx.
approx.
Transmission current approx.
Operating temperature
Range
with good free field conditions approx.
in buildings approx.
Dimensions approx.
Weight approx.
- Blinking symbol: exchange the battery.
(see chapter E).
-programmed
switching commands in Automatic Mode: check
whether the Time Switch is in "Automatic Mode" (see
chapter C5). Check the programmed switching times
(see chapter C4.1). If necessary, re-enter the radio
channels of the radio timer into the radio controls
(see chapter B2).
-Solar protection/twilight mode cannot be activated:
re-establish the connection between the light sensor
and the ttime switch (see the operating instructions
for the Light Sensor SL01).
-The radio control does not move the shutter into the
intermediate position: set the runtime again (see
chapter B3).
-After changing the sensor´s battery, the light sensor
reception is disrupted and the SUN/MOON icon
blinks: Wait approx. 35 minutes until reception is
restored automatically.
- If there is no visible display: check the batterie´s
polarity or exchange the battery
- If the control does not react to pressing buttons in
manual operation: re-enter the radio channels of the
Radio Time Switch into the radio controls (see
chapter B2).
If the radio control does not react to the
The battery capacity is shown in the display with the
symbol . If the complete battery symbol blinks the
battery needs to be exchanged.
The clock has a power reserve of some
minutes. If the radio time switch is without
voltage supply for a longer period, only the time
has to be reset
. All other settings remain as they
were.
If the bar of the battery icon blinks and the contur
shows permanently on the display of the time switch,
the battery of the light sensor needs to be exchanged.
Also see the operating instructions of the Light Sensor
SL01.
UM80508B 1017 GB
Warranty
Within the statutory warranty period we undertake to
rectify free of charge by repair or replacement any
product defects arising from material or production
faults.
Any unauthorized tampering with, or modifications to,
the product shall render this warranty null and void.
Replace the time switch in the wall mount. The
latches have to snap into place.
Exchange the battery.
Only use batteries of the
type CR2032.
Observe the correct
polarity!
Press the radio
timeswitch together in
the center on the top
and the bottom and pull
it out of the wall mount.
D1 Activating the Holiday Mode
DAdditional Functions
C6 Manual Mode
In manual mode you can only raise or lower the
shutters by pushing a button.
DOWN
STOP
UP
(raise) (lower)
D4 ng D RDeleti all ata ( eset)
D2 Activating Daylight Savings Time
CH
CLOCK
W
MO TU WE FR SATH SU
AUTO
HOLI
S/W DEL
S
AUTO
MO TU WE FR SA SOTH
Set the time switch to operating mode (ESC).
Press the S/W button for
more than 3 seconds.
The display changes
from W to S
and the clock is moved
forwards/backwards one hour.
HOLI
S/W DEL
D3 Activate Vacation Mode
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
S
AUTO
MO TU WE FR SA SOTH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
MANU
W
MO TU WE TH FR SA SO
Press ESC and the DEL button at the
same time for more than 3 seconds.
All saved data are
deleted and the
factory settings are
restored.
After a RESET the radio channels do not
have to be learned into the radio control
again.
PROG ADJ
MODE
ESC
S/W DEL
HOLI
ESC
HOLI
S/W DEL
MANU
W
MANU
W
MANU
W
MANU
W
MANU
W
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
MO TU WE FR SA SOTH
Scope of Delivery
Radio Time Switch RTS07, battery CR2032, -
ment frame, attachment set, operating instructions
attach
Please read these instructions carefully
before using the product
Also observe the operating instructions of the
devices to be controlled
The automatic control of systems or devices that
need to be supervised is not permitted.
Have faulty Radio Time Switches checked by the
manufacturer
!
Do not make any unauthorized modifications to the
device!
!
Safety Advice
C5 Changing the Operating Mode
Automatic Mode
Set the time switch to operating mode (ESC).
By briefly pressing the MODE button, select
the operating mode AUTO (automatic
mode) or AUTOMANU (automatic mode
with partial manual operation).
MANU
W
MO TU WE FR SA SOTH
AUTO
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
PROG
MODE
W
MO TU WE FR SA SOTH
AUTO
Solar Protection/Twilight Mode
Set the time switch to operating mode (ESC).
By briefly pressing the SUN/MOON button,
activate/deactivate solar protection, twilight
or both modes.
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
MO TU WE FR SA SOTH
W
AUTO
TH
W
AUTO
TH
CH
OK CLOCK
PROG ADJ
MODE
ESC
S/WDEL
HOLI
ADJ
4/4
G IGeneral nformation